A mixed-lubrication model considering the oil supply was developed. The elastoplastic model was applied in the asperity contact simulation. The oil-film thickness at the ring–cylinder liner interface was determined using a mass conservation algorithm. The modeling results were compared with experimental results for verification on a reciprocating wear tester. It is found that, under the fully flooded condition, the results of the Greenwood–Trip model and the current model in the middle of the stroke are in accordance with the experimental results, but the results of the current model at the ends of the stroke are closer to the experimental results than the Greenwood–Trip model results are. Under the starved-lubrication condition, the friction coefficient of the current method is closer to the experimental result than that of the Greenwood–Trip model in the entire stroke. Therefore, the model developed in this study is appropriate for mixed lubrication under the fully flooded condition and the starved-lubrication condition. Furthermore, the model was applied to the ring pack of a diesel engine to study the effect of the oil supply on the tribological performance. The results show that the frictional forces under the 1 μm oil supply condition are far larger than those under the sufficient oil supply condition in the middle of the stroke, and so the increase in the frictional force may be used to identify scuffing failure in future studies if the relationships between the frictional forces and the measured vibration signals of the engine are obtained.
AnderssonBS. Company’s perspective in vehicle tribology. In: Wear particles: from the cradle to the grave, 18th Leeds–Lyon symposium on tribology, Elevier Tribology Series, Vol 21, Lyon, France, 3–6 September 1991, pp. 503–506. Amsterdam: Elsevier.
2.
BakerCETheodossiadesSRahnejatH. Influence of in-plane dynamics of thin compression rings on friction in internal combustion engines. Trans ASME, J Engng Gas Turbines Power2012; 134: 092801.
3.
GoreMTheakerMHowell-SmithS. Direct measurement of piston friction of internal-combustion engines using the floating-liner principle. Proc IMechE Part D: J Automobile Engineering2014; 228(3): 344–354.
4.
NamazianMHeywoodJB. Flow in the piston-cylinder-ring crevices of a spark-ignition engine: effect on hydrocarbon emissions, efficiency and power. SAE paper 820088, 1982.
5.
DowsonDEconomouPNRuddyBL. Piston ring lubrication – Part I: theoretical analysis of a single ring and complete ring pack. In: Energy conservation through fluid film lubrication technology: frontiers in research and design, 1979, pp. 23–52. New York: ASME.
6.
RuddyBLDowsonDEconomouPNBakerAJS. Piston ring lubrication – Part II: the influence of ring dynamics and ring twist. In: Energy conservation through fluid film lubrication technology: frontiers in research and design, 1979, pp. 191–215. New York: ASME.
7.
RhodeSM. A mixed friction model for dynamically loaded contacts with application to piston ring lubrication. In: 7th Leeds–Lyon symposium on tribology, Leeds, UK, 9–12 September 1980, pp. 262–278. Guildford: Westbury House.
8.
PatirNChengHS. An average flow model for determining effects of three-dimensional roughness on partial hydrodynamic lubrication. Trans ASME, J Lubr Technol1978; 100: 12–17.
9.
PatirNChengHS. Application of average flow model to lubrication between rough sliding surfaces. Trans ASME, J Lubr Technol1979; 101: 220–230.
10.
GreenwoodIATrippJH. The contact of two nominally flat surfaces. Proc IMechE1970; 185(1): 625–633.
11.
JengYR. Theoretical analysis of piston-ring lubrication – Part I: fully flooded lubrication. Tribol Trans1992; 35: 696–706.
12.
JengYR. Theoretical analysis of piston-ring lubrication – Part II: starved lubrication and its application to a complete ring pack. Tribol Trans1992; 35: 707–714.
HanDCLeeJS. Analysis of the piston ring lubrication with a new boundary condition. Tribol Int1998; 31: 753–760.
15.
NakaiHInoNHashimotoH. Piston-ring lubrication problems for refrigeration compressors considering combined effects of supply oil quantity and surface roughness. Trans ASME, J Tribol1996; 118: 286–291.
16.
TianT. Modeling the performance of the piston ring-pack in internal combustion engines. PhD Thesis, Massachusetts Institute of Technology, Boston, Massachusetts, USA, 1997.
17.
LiuL. Modeling the performance of the piston ring-pack with consideration of non-axisymmetric characteristics of the power cylinder system in internal combustion engines. PhD Thesis, Massachusetts Institute of Technology, Boston, Massachusetts, USA, 2005.
18.
PriestMDowsonDTaylorCM. Theoretical modelling of cavitation in piston ring lubrication. Proc IMechE Part C: J Mechanical Engineering Science2000; 214(3): 435–447.
19.
MuftiRAPriestMChittendenRJ. Analysis of piston assembly friction using the indicated mean effective pressure experimental method to validate mathematical models. Proc IMechE Part D: J Automobile Engineering2008; 222(8): 1441–1457.
20.
NovotnyPPistekVDrapalL. Efficient approach for solution of the mechanical losses of the piston ring pack. Proc IMechE Part D: J Automobile Engineering2013; 227(10): 1377–1388.
21.
KeribarRDursunkayaZFlemmingMF. An integrated model of ring pack performance. Trans ASME, J Engng Gas Turbines Power1991; 113: 382–389.
22.
ShahmohamadiHRahmaniRRahnejatH. Thermo-mixed hydrodynamics of piston compression ring conjunction. Tribol Lett2013; 51: 323–340.
23.
RahmaniRTheodossiadesSRahnejatHFitzsimonsB. Transient elastohydrodynamic lubrication of rough new or worn piston compression ring conjunction with an out-of-round cylinder bore. Proc IMechE Part J: J Engineering Tribology2012; 226(4): 284–305.
24.
ChoSWChoiSMBaeCS. Friction modes of barrel shaped piston rings under flooded lubrication. Tribol Int2000; 33: 545–551.
25.
TruhanJJQuJBlauPJ. A rig test to measure friction and wear of heavy duty diesel engine piston rings and cylinder liners using realistic lubricants. Tribol Int2005; 38: 211–218.
26.
BolanderNWSteenwykBDSadeghiFGerberGR. Lubrication regime transitions at the piston ring–cylinder liner interface. Proc IMechE Part J: J Engineering Tribology2005; 219(1): 19–31.
27.
JacksonRLGreenI. A finite element study of elasto-plastic hemispherical contact against a rigid flat. Trans ASME, J Tribol2005; 127: 343–354.
28.
KogutLEtsionI. A static friction model for elastic–plastic contacting rough. Trans ASME, J Tribol2004; 126: 34–40.
29.
JacksonRLDuvvuruRSMeghaniHMahajanM. An analysis of elasto-plastic sliding spherical asperity interaction. Wear2007; 262: 210–219.
30.
MulvihillDMKartalMENowellDHillsDA. An elastic–plastic asperity interaction model for sliding friction. Tribol Int2011; 44: 1679–1694.
31.
LiLEtsionITalkeFE. Contact area and static friction of rough surfaces with high plasticity index. Trans ASME, J Tribol2010; 132.
32.
MasjediMKhonsariMM. Theoretical and experimental investigation of traction coefficient in line-contact EHL of rough surfaces. Tribol Int2014; 70: 179–189.
33.
LiuGLiuTXieQWangQJ. Two-dimensional steady-state thermal elasto-plastic contact of rough surfaces. Proc IMechE Part J: J Engineering Tribology2008; 222(7): 843–855.
34.
HaddadSDTianKT. An analytical study of offset piston and crankshaft designs and the effect of oil film on piston slap excitation in a diesel engine. Mech Mach Theory1995; 30: 271–284.
35.
YeXM. Numerical investigation and application of three-dimensional lubrication performance in piston ring pack. PhD Thesis, Huazhong University of Science and Technology, Wuhan, People's Republic of China, 2004.
36.
MorrisNRahmaniRRahnejatH. The influence of piston ring geometry and topography on friction. Proc IMechE Part J: J Engineering Tribology2013; 227(2): 141–153.
37.
ZhuDChengHSAraiTHamaiK. A numerical analysis for piston skirts in mixed lubrication – Part I: basic modeling. Trans ASME, J Tribol1992; 114: 553–562.
38.
JacksonRLGreenI. A statistical model of elasto-plastic asperity contact between rough surfaces. Tribol Int2006; 39: 906–914.
39.
ChengFQ. Analysis and research of piston ring-cylinder lubrication in internal combustion engine. MEng Thesis, Shandong University, Jinan, People's Republic of China, 2005.
40.
MorrisNRahmaniRRahnejatH. Tribology of piston compression ring conjunction under transient thermal mixed regime of lubrication. Tribol Int2013; 59: 248–258.
41.
HarigayaYSuzukiMTodaFTakiguchiM. Analysis of oil film thickness and heat transfer on a piston ring of a diesel engine: effect of lubricant viscosity. Trans ASME, J Engng Gas Turbines Power2006; 128: 685–693.
42.
PapadopoulosPPriestMRainforthWM. Investigation of fundamental wear mechanisms at the piston ring and cylinder wall interface in internal combustion engines. Proc IMechE Part J: J Engineering Tribology2007; 221(3): 333–343.
