More than one decade with development of common-rail diesel engine management systems: a literature review on modelling,control,estimation and calibration
Restricted accessReview articleFirst published online July, 2015
More than one decade with development of common-rail diesel engine management systems: a literature review on modelling,control,estimation and calibration
Diesel engines are becoming more popular owing to their low fuel consumption and low emissions. The performance and emissions of diesel engines are strictly influenced by the injection pattern and the induced air quality. Utilization of diesel engines with mechatronic systems together with the advent of common-rail injection systems, which promotes the flexibility of injection control, has further increased diesel engine favourability and decreased the level of relevant emissions and noise. Development of mechatronic systems is a hierarchical procedure; in particular, in the case of common-rail diesel engine control, the extent and diversity of involved topics lead to a complex multi-stage development procedure. Many research studies have been carried out, thereby providing much literature in this field, which addresses different aspects of the development procedure for diesel engine management systems. Investigation of the existing literature will help researchers in the field to obtain a better understanding of the whole development procedure of diesel engine management systems and to make them familiar with new trends, state-of-the-art technologies and research fields. In this article, the control strategy development of common-rail diesel engine management systems is considered using the existing literature, i.e. the related literature was collected and categorized into the five main categories of modelling, sensitivity analysis, controller design, estimation and calibration. A brief description of every category followed by the relevant literature is given in the paper, and the common methods as well as the state-of-the-art techniques are discussed in each section. Finally, the strengths and weaknesses of the existing methods and the potential for further advancement are mentioned for each stage of the development of the engine management system, and a road map for the development of a common-rail diesel engine management system is presented.
KienckeUNielsenL. Automotive Control Systems For Engine, Driveline, and Vehicle. Berlin: Springer, 2005.
6.
GrondinOStobartRChafoukHMaquetJ. Modelling the compression ignition engine for control: review and future trends. SAE paper 2004-01-0423, 2004.
7.
JensenJPKristensenAFSorensonSC. Mean value modeling of a small turbocharged diesel engine. SAE paper 910070, 1991.
8.
BenzMOnderCHGuzzellaL. Engine emission modeling using a mixed physics and regression approach. Trans ASME, J Engng Gas Turbines Power2010; 132(4): 042803.
9.
ZhangJLanH. Fuzzy modeling of diesel engine based on working position. In: International conference on system science and engineering, Dalian, Liaoning, People’s Republic of China, 30 June–2 July 2012, pp. 514–517. New York: IEEE.
10.
GiakoumisEGAlafouzosAI. Study of diesel engine performance and emissions during a transient cycle applying an engine mapping-based methodology. Appl Energy2010; 87: 1358–1365.
11.
KolmanovskyIMoraalPvan NieuwstadtMStefanopoulouA. Issues in modeling and control of intake flow in variable geometry turbocharged engines. In: 18th IFIP conference on system modelling and optimization, Detroit, Michigan, USA, 22–25 July 1997, pp. 436–445. Boca Raton, Florida: CRC Press, 1999.
12.
RakopoulosCDGiakoumisEG. Review of thermodynamic diesel engine simulations under transient operating conditions. SAE paper 2006-01-0884, 2006.
13.
DinescuDCTazeroutM. Mean value modeling of a variable nozzle turbocharger (VNT). Univ Politehn Bucharest Scient Bull, Ser D: Mech Engng2010; 72(1): 109–116.
14.
NikzadfarKShamekhiAH. Developing a state space model for a turbocharged diesel engine using the subspace identification method. Proc IMechE Part D: J Automobile Engineering2011; 225: 1692–1706.
15.
SalcedoJVMartinezM. LPV identification of a turbocharged diesel engine. Appl Numer Math2008; 58: 1553–1571.
16.
ZitoGLandauID. Narmax model identification of a variable geometry turbocharged diesel engine. In: American control conference, Portland, Oregon, USA, 8–10 June 2005, Vol 2, pp. 1021–1026. New York: IEEE.
17.
García-NietoSSalcedoJMartínezMLauríD. Air management in a diesel engine using fuzzy control techniques. Inf Sci2009; 179: 392–3409.
18.
HanQYangFZhouMOuyang MO. Study on modeling method for common rail diesel engine calibration and optimization. SAE paper 2004-01-0426, 2004.
19.
HafnerMSchuKMNellesOIsermannR. Fast neural networks for diesel engine control design. Control Engng Practice2000; 8: 1211–1221.
20.
OuladsineMBlochGDovifazzX. Neural modelling and control of a diesel engine with pollution constraints. J Intell Robotic Systems2004; 41: 157–171.
21.
AlbrechtAGrondinOBerrFLSolliecGL. Towards a stronger simulation support for engine control design. Oil Gas Sci Technol – Rev IFP2007; 62(4): 437–456.
22.
LiRHuangYLiGSongH. Control-oriented modeling and analysis for turbocharged diesel engine system. In: International conference on measurement, information and control, Harbin, People’s Republic of China, 16–18 August 2013, Vol 2, pp. 855–860. New York: IEEE.
23.
TorkzadehDDLäangstWKienckeU. Combustion and exhaust gas modeling of a common rail diesel engine – an approach. SAE paper 2001-01-1243, 2001.
24.
RakopoulosCDRakopoulosDCGiakoumisEGKyritsisDC. Validation and sensitivity analysis of a two zone diesel engine model for combustion and emissions prediction. Energy Conversion Managmt2004; 45: 1471–1495.
25.
ParkSWBangSHLeeKH. Atomization characteristics of common-rail diesel injector with multi-hole. SAE paper 2003-01-1833, 2003.
26.
AithalSM. Modeling of NOx formation in diesel engines using finite-rate chemical kinetics. Appl Energy2010; 87: 2256–2265.
27.
HiroyasuHMiaoHHiroyasuT. Genetic algorithms optimization of diesel engine emissions and fuel efficiency with air swirl, EGR, injection timing and multiple injections. SAE paper 2003-01-1853, 2003.
28.
AsprionJChinellatoOGuzzellaL. A fast and accurate physics-based model for the NOx emissions of diesel engines. Appl Energy2013; 103: 221–233.
29.
BarbaCBurkhardtCBoulouchosKBargendeM. A Phenomenological combustion model for heat release rate prediction in high-speed DI diesel engines with common rail injection. SAE paper 2000-01-2933, 2000.
30.
SeykensXLJBaertRSGSomersLMT. Experimental validation of extended NO and soot model for advanced HD diesel engine combustion. SAE paper 2009-01-0683, 2009.
31.
GalindoJLujanJMSerranoJRHernandezL. Combustion simulation of turbocharger HSDI diesel engines during transient operation using neural networks. Appl Thermal Engng2005; 25: 877–898.
32.
RakopoulosCDDimaratosAMGiakoumisEGRakopoulosDC. Exhaust emissions estimation during transient turbocharged diesel engine operation using a two-zone combustion model. Int J Veh Des2009; 49: 125–149.
33.
ShaylerPNgH. Simulation studies of the effect of fuel injection pattern on NO and soot formation in diesel engines. SAE paper 2004-01-0116, 2004.
34.
BirtasAChiriacR. A study of injection timing for a diesel engine operation with gasoil and HRG gas. Univ Politehn Bucharest Scient Bull, Ser D: Mech Engng2011; 73(4): 65–78.
35.
VoicuAIChiriacR. A numerical simulation of the influence of injection characteristics on performance and emissions of a tractor diesel engine. Univ Politehn Bucharest Scient Bull, Ser D: Mech Engng2012; 74(3): 43–54.
36.
JafariBGanjiDDMirsalimM. Experimental and numerical investigation of the effect of exhaust gas recirculation on performance and emissions of a dual fuel (diesel–gas) engine. Aust J Basic Appl Sci2013; 7(7): 668–678.
37.
BorettiAA. Numerical evaluation of the performance of a compression ignition CNG engine for heavy duty trucks with an optimum speed power turbine. Int J Engng Technol Innovation2011; 1(1): 12–26.
38.
BakarRAIsmailAR. Investigation of diesel engine performance based on simulation. Am J Appl Sci2008; 5(6): 610–617.
39.
PangKMNgHKGanS. Investigation of fuel injection pattern on soot formation and oxidation processes in a light-duty diesel engine using integrated CFD-reduced chemistry. Fuel2012; 96: 404–418.
40.
MorselliRCortiERizzoniG. Energy based model of a common rail injector. In: 2002 international conference on control applications, Glasgow, UK, 17–20 September 2002, pp. 1195–2000. New York: IEEE.
41.
BianchiGMFalfariSPelloniP. Numerical analysis of high-pressure fast-response common rail injector dynamics. SAE paper 2002-01-0213, 2002.
42.
BianchiGMFalfarSParottoMOsbatG. Advanced modeling of common rail injector dynamics and comparison with experiments. SAE paper 2003-01-0006, 2003.
43.
GanserMA. Common rail injector with injection rate control. SAE paper 981927, 1998.
44.
SeykensXLJSomersLMTBaertRSG. Modelling of common rail fuel injection system and influence of fluid properties on injection process. In: International conference on vehicle alternative fuel systems and environmental protection, Dublin, Ireland, 6–9 July 2004, pp. 72–77. Dublin: Dublin City University.
45.
LinoPMaioneBRizzoA. Nonlinear modelling and control of a common rail injection system for diesel engines. Appl Mathl Modelling2007; 31: 1770–1784.
46.
CatalanoLATondoloVADadoneA. Dynamic rise of pressure in the common-rail fuel injection system. SAE paper 2002-01-0210, 2002.
47.
KöhlSJegminatD. How to do hardware-in-the-loop simulation right. SAE paper 2005-01-1657, 2005.
48.
LeeWYoonMSunwooM. A cost and time effective hardware in the loop simulation platform for automotive engine control systems. Proc IMechE Part D: J Automobile Engineering2003; 217(1): 41–52.
49.
SchulzeTWiedemeierMSchuetteH. Crank angle-based diesel engine modeling for hardware-in-the-loop applications with in-cylinder pressure sensors. SAE paper 2007-01-1303, 2007.
50.
ShaylerPJAllenAJRobertsAL. Running real-time engine model simulation with hardware-in-the-loop for diesel engine development. SAE paper 2005-01-0056, 2005.
51.
CarlucciPFicarellaALaforgiaD. Study of the influence of the injection parameters on combustion noise in a common rail diesel engine using ANOVA and neural networks. SAE paper 2001-01-2011, 2001.
52.
AgarwalAKSrivastavaDKDharA. Effect of fuel injection timing and pressure oncombustion, emissions and performance characteristics of a single cylinder diesel engine. Fuel2013; 111: 374–383.
53.
KannanKUdayakumarM. Experimental study of the effect of fuel injection pressure on diesel engine performance and emission. ARPN J Engng Appl Sci2010; 5(5): 42–45.
54.
GomesPYatesD. The influence of some engine operating parameters on particulate emissions. SAE paper 922222, 1992.
55.
TaninKVWickmanDDMontgomeryDT. The influence of boost pressure on emissions and fuel consumption of a heavy-duty single-cylinder D.I. diesel engine. SAE paper 1999-01-0840, 1999.
56.
RakopoulosCDRakopoulosDCGiakoumisEGKyritsisDC. Validation and sensitivity analysis of a two zone diesel engine model for combustion and emissions prediction. Energy Conversion Managmt2004; 45: 1471–1495.
57.
LiuSHwangJWKimMH. Simulating the effects of fuel injection characteristics on DI diesel engine emissions. In: 2000 FISITA world automotive congress, Seoul, Republic of Korea, 12–15 June 2000, paper F2000A009, pp. 1–5. London: FISITA.
58.
WangXHuangZZhangW. Effects of ultra-high injection pressure and micro-hole nozzle on flame structure and soot formation of impinging diesel spray. Appl Energy2010; 88: 1620–1628.
59.
JayashankaraBGanesanV. Effect of fuel injection timing and intake pressure on the performance of a DI diesel engine – a parametric study using CFD. Energy Conversion Managmt2010; 51: 1835–1848.
60.
NgHKShaylerPJ. CFD investigation of the effects of split main fuel injection parameters on combustion and emissions in a light-duty diesel engine. In: 1st regional conference on vehicle engineering and technology, Kuala Lumpur, Malaysia, 3–5 July 2006.
61.
JeftícMYuSHanX. Zheng M. Effects of postinjection application with late partially premixed combustion on power production and diesel exhaust gas conditioning. J Combust2011; Article ID 891096: 9 pp.
62.
MitoYTanakaDLeeS. The effect of intake, injection parameters and fuel properties on diesel combustion and emissions. SAE paper 2003-01-1793, 2003.
63.
BianchiGPelloniPCorcioneFLuppinoF. Numerical analysis of passenger car HSDI diesel engines with the 2nd generation of common rail injection systems: the effect of multiple injections on emissions. SAE paper 2001-01-1068, 2001.
64.
Al-HintiISamhouriMAl-GhandoorASakhriehA. The effect of boost pressure on the performance characteristics of a diesel engine: a neuro-fuzzy approach. Appl Energy2008; 86: 113–121.
65.
UzunA. A parametric study for specific fuel consumption of an intercooled diesel engine using a neural network. Fuel2012; 93: 189–199.
66.
ParlakAIslamogluYYasarHEgrisogutA. Application of artificial neural network to predict specific fuel consumption and exhaust temperature for a diesel engine. Appl Thermal Engng2006; 26: 824–828.
67.
TennisonPJReitzR. An experimental investigation of the effects of common-rail injection system parameters on emissions and performance in a high-speed direct-injection diesel engine. Trans ASME, J Engng Gas Turbines Power2001; 163(1): 167–174.
68.
CarlucciPFicarellaALaforgiaD. Pilot injection behavior and its effects on combustion in a common rail diesel engine. In: International workshop on modeling, enissions and control in automotive engines, Fisciano, Salerno, Italy, 9–10 September 2001, paper MECA01-06.
69.
BadamiMMallamoFMilloFRossiEE. Influence of multiple injection strategies on emissions, combustion noise and BSFC of a DI common rail diesel engine. SAE paper 2002-01-0503, 2002.
70.
ZhengMKumarR. Implementation of multiple-pulse injection strategies to enhance the homogeneity for simultaneous low-NOx and -soot diesel combustion. Int J Thermal Sci2009; 48: 1829–1841.
71.
HillionMBuhlbuckHChauvinJPetitN. Combustion control of diesel engines using injection timing. SAE paper 2009-01-0367, 2009.
72.
PayriFBroatchASalavertJMMartínJ. Investigation of diesel combustion using multiple injection strategies for idling after cold start of passenger-car engines. Exptl Thermal Fluid Sci2010; 34: 857–865.
73.
AnSChangHXuH. Examinatal study on common rail diesel engine for multi-injection strategies. In: International conference on intelligent computation technology and automation, Changsha, Hunan, People’s Republic of China, 11–12 May 2010, Vol 2, pp. 258–261. New York: IEEE.
74.
NikzadfarKShamekhiAH. Investigating the relative contribution of operational parameters on performance and emissions of a common-rail diesel engine using neural network. Fuel2014; 125: 116–128.
75.
ParlakAYasarHHasimogluCKolipA. The effects of injection timing on NOx emissions of a low heat rejection indirect diesel injection engine. Appl Thermal Engng2005; 25: 3042–3052.
76.
van de WalMde JagerB. A review of methods for input/output selection. Automatica2001; 37: 487–510.
77.
DeignanPBKingGBMecklPHJenningsK. Confidence measure estimation in dynamical systems model input set selection. In: 2004 American control conference, Boston, Massachusetts, USA, 30 June–2 July 2004, Vol 3, pp. 2824–2829. New York: IEEE.
78.
NareidHGrimesMVerdejoJ. A Neural network based methodology for virtual sensor development. SAE paper 2005-01-0045, 2005.
79.
ZweiriYHSeneviratneLD. Diesel engine indicated and load torque estimation using a non-linear observer. Proc IMechE Part D: J Automobile Engineering2001; 220(6): 775–785.
80.
BrahmaAUpadhyayDSerraniARizzoniG. Modeling, identification and state estimation of diesel engine torque and NOx dynamics in response to fuel quantity and timing excitations. In: 2004 American control conference, Boston, Massachusetts, USA, 30 June–2 July 2004, Vol 3, pp. 2166–2171. New York: IEEE.
81.
BrahmaISharpMCFrazierTR. Estimation of engine torque from a first law based regression model. SAE paper 2008-01-1014, 2008.
82.
FrancoaJFranchekbMAGrigoriadisbK. Real-time brake torque estimation for internal combustion engines. Mech Systems Signal Processing2008; 22: 338–361.
83.
FalconePFiengoGGlielmoL. Non-linear net engine torque estimator for internal combustion engine. In: IFAC symposium on advances in automotive control, Salerno, Italy, 19–23 April 2004, Vol 1, pp. 125–130. Oxford: Elsevier.
84.
FalconePFiengoGGlielmoL. Nicely nonlinear engine torque estimator. In: 16th IFAC world congress, Prague, Czech Republic, 4–8 July 2005, p. 1923. Laxenburg: IFAC.
85.
ZweiriYH. Diesel engine indicated torque estimation based on artificial neural networks. In: International conference on computer systems and applications, Amman, Jordan, 13–16 May 2007, pp. 791–l798. New York: IEEE.
86.
CastilloFWitrantETalonVDugardL. Simultaneous air fraction and low-pressure EGR mass flow rate estimation for diesel engines. In: 5th IFAC symposium on system structure and control, Grenoble, France, 4–6 February 2013, pp. 731–736. Laxenburg: IFAC.
87.
StotskyAKolmanovskyI. Application of input estimation techniques to charge estimation and control in automotive engines. Control Engng Practice2002; 10: 1371–1383.
88.
DesantesJMGalindoJGuardiolaCDolzV. Air mass flow estimation in turbocharged diesel engines from in-cylinder pressure measurement. Expl Thermal Fluid Sci2009; 34: 37–47.
89.
StorsetOFStefanopoulouAGSmithR. Adaptive air charge estimation for turbocharged diesel engines without exhaust gas recirculation. Trans ASME, J Dynamic Systems, Measmt, Control2004; 126(3): 633–643.
90.
PoloniTRohal-IlkivBJohansenTA. Mass flow estimation with model bias correction for a turbocharged diesel engine. Control Engng Practice2014; 23: 22–31.
91.
Al-DurraAFiorentiniLCanovaMYurkovichS. A model-based estimator of engine cylinder pressure imbalance for combustion feedback control applications. In: 2011 American control conference, San Francisco, California, USA, 2011, pp. 991–996. New York: IEEE.
92.
HenningssonMTunestalPJohanssonR. A virtual sensor for predicting diesel engine emissions from cylinder pressure data. In: 2012 IFAC workshop on engine and powertrain control, simulation and modeling, Rueil-Malmaison, France, 23–25 October 2012, pp. 424–431. Laxenburg: IFAC.
93.
ChauvinJMoulinPCordeG. Real-time nonlinear individual cylinder air fuel ratio observer on a diesel engine test bench. In: 16th IFAC world congress, Prague, Czech Republic, 4–8 July 2005, p. 1919. Laxenburg: IFAC.
JankovicM. Nonlinear control in automotive engine applications. In: 15th international symposium on mathematical theory of networks and systems, Notre Dame, Indiana, USA, 12–16 August 2002, paper FA7, pp. 1–9.
96.
StewartGBorrelliF. A model predictive control framework for industrial turbodiesel engine control. In: 47th IEEE conference on decision and control, Cancun, Mexico, 9–11 Decemebre 2008, pp. 5704–5711. New York: IEEE.
97.
OmranRYounesRChampoussinJC. Genetic algorithm for dynamic calibration of engine’s actuators. SAE paper 2007-01-1079, 2007.
98.
LivshizMKaoMWillA. Engine torque control variation analysis. SAE paper 2008-01-1016, 2008.
99.
PetterssonMNielsenL. Diesel engine speed control with handling of driveline resonances. Control Engng Practice2002; 11: 319–328.
100.
OstmanFToivonenHT. Active torsional vibration control of reciprocating engines. Control Engng Practice2007; 16: 78–88.
101.
YeZ. Modeling, Identification, design and implementation of nonlinear automotive idle speed control systems – an overview. IEEE Trans System, Man, Cybernetics, Part C Applic Rev2007; 37(6): 1137–1151.
102.
KimDParkJ. Application of adaptive control to the fluctuation of engine speed at idle. Inf Sci2007; 177: 3341–3355.
103.
NikzadfarKShamekhiAH. Optimal idle speed control of a light dusty turbodiesel engine aiming at minimizing fuel consumption. SAE paper 2011-01-0713, 2011.
104.
YanFWangJ. Air- and fuel-path coordinated control for advanced combustion mode transitions in diesel engines. In: American control conference, Montreal, Quebec, Canada, 27–29 June 2012, pp. 2890–2895. New York: IEEE.
105.
AlfieriEAmstutzAGuzzellaL. Gain-scheduled model-based feedback control of the air/fuel ratio in diesel engines. Control Engng Practice2008; 17: 1417–1425.
106.
TschanzFAmstutzAOnderCHGuzzellaL. Feedback control of particulate matter and nitrogen oxide emissions in diesel engines. Control Engng Practice2012; 21(12): 1809–1820.
107.
BieniekA. Conception of cylinder pressure based diesel injection control system. J KONES Powertrain and Transport2011; 18(3): 27–35.
108.
ArnoldJFLangloisNChafouH. Fuzzy controller of the air system of a diesel engine: real-time simulation. Eur J Opl Res2009; 193: 282–288.
109.
CapobiancoM. Optimum control of an automotive direct injection diesel engine for low exhaust emissions. Proc IMechE Part D: J Automobile Engineering2001; 215(11): 1225–1236.
110.
WijetungeRSHawleyJGVaughanND. An exhaust pressure control strategy for a diesel engineProc IMechE Part D: J Automobile Engineering2004; 218(4): 449–464.
111.
WangaYYHaskaraIYanivO. Quantitative feedback design of air and boost pressure control system for turbocharged diesel engines. Control Engng Practice2011; 19(6): 626–637.
112.
RajamaniR. Control of a variable-geometry turbocharged and wastegated diesel engine. Proc IMechE Part D: Journal of Automobile Engineering2005; 219(11); 1361–1368.
113.
García-NietoSMartínezMBlascoXSanchisJ. Nonlinear predictive control based on local model networks for air management in diesel engines. Control Engng Practice2008; 16: 1399–1413.
114.
AliSAN’doyeBNicolasL. Sliding mode control for turbocharged diesel engine. In: 20th Mediterranean conference on control and automation, Barcelona, Spain, 3–6 July 2012, pp. 996–1001. New York: IEEE.
115.
FerreauHJOrtnerPLangthalerP. Predictive control of a real-world diesel engine using an extended online active set strategy. A Rev Control2007; 32: 293–301.
116.
WangHZhangYWangJ. Studies of control strategies for high pressure common rail diesel engine. In: IEEE vehicle power and propulsion conference, Harbin, People’s Republic of China, 3–5 September 2008, pp.1–5. New York: IEEE.
117.
GauthierCSenameODugardLMeissonnierG. Modelling of a diesel engine common rail injection system. In: 16th IFAC world congress, Prague, Czech Republic, 4–8 July 2005, p. 1918. Laxenburg: IFAC.
118.
TanabeKKohketsuSMoriKKawaiK. Innovative injection rate control with next generation common rail fuel injection system. In: 2000 FISITA world automotive congress, Seoul, Republic of Korea, 12–15 June 2000, paper F2000A055, pp. 1–8. London: FISITA.
119.
LinoPMaioneBRizzoA. Nonlinear modelling and control of a common rail injection system for diesel engines. Appl Mathl Modelling2007; 31: 1770–1784.
120.
LiuYZhangYTianHQinJ. Research and applications for control strategy of high-pressure common rail injection system in diesel engine. In: IEEE vehicle power and propulsion conference, Harbin, People’s Republic of China, 3–5 September 2008, pp. 1–6. New York: IEEE.
121.
SuHHaoGLiPLuoX. Feed forward fuzzy PID controller for common-rail pressure control of diesel engine. In: International conference on measuring technology and mechatronics automation, Changsha, Hunan, People’s Republic of China, 13–14 March 2010, Vol 2, pp. 264–267. New York: IEEE.
122.
YanFWangJ. Common rail injection system on-line parameter calibration for precise injection quantity control. In: American control conference, Baltimore, Maryland, USA, 30 June–2 July 2010, pp. 2248–2253. New York: IEEE.
123.
GuoSZhangTMuseumH. The multi-pulse control algorithm of high pressure common rail diesel engine based on structure array. In: International conference on information and automation, Shenyang, People’s Republic of China, 6–8 June 2012, pp. 837–840. New York: IEEE.
124.
MichaelB. Model-based optimal emission control of diesel engines. PhD Thesis, Dissertation ETH 18796, ETH Zürich, Zürich, Switzerland, 2010.
125.
SassanoMPassenbrunnerTEHirschM. Approximate optimal control of the air path of a diesel engine. In: American control conference, Montreal, Quebec, Canada, 27–29 June 2012, pp. 4204–4209. New York: IEEE.
126.
KuangBWangYTanYL. An H∞ controller design for diesel engine systems. In: International conference on power system technology, Perth, Western Australia, Australia, 4–7 December 2000, Vol 1, pp. 61–66. New York: IEEE.
127.
SuHZhangYWangJLiuL. Researches of common-rail diesel engine emission control based on cylinder pressure feedback. In: IEEE vehicle power and propulsion conference, Harbin, People’s Republic of China, 3–5 September 2008, pp. 1–6. New York: IEEE.
128.
JeschkeJ. Conception and test of a cylinder pressure based engine management for passenger car diesel engines. PhD Thesis, University of Magdeburg, Magdeburg, Germany, 2002.
129.
StefanopoulouAGKolmanovskyIFreudenbergJS. Control of variable geometry turbocharged diesel engines for reduced emissions. IEEE Trans Control Systems Technol2000; 8(4): 733–745.
130.
LangouetHMetivierLSinoquetDTranQH. Optimization for engine calibration. In: International conference on engineering optimization, Rio de Janeiro, Brazil, 1–5 June 2008, pp. 1–10.
131.
WinZGakkharRPJainSCBhattacharyaM. Parameter optimization of a diesel engine to reduce noise, fuel consumption, and exhaust emissions using response surface methodology. Proc IMechE Part D: J Automobile Engineering2005; 219(10): 1181–1192.
132.
AtkinsonCAllainMZhangH. Using model-based rapid transient calibration to reduce fuel consumption and emissions in diesel engines. SAE paper 2008-01-1365, 2008.
133.
de RisiACarlucciPDonateoTFicarellaA. A combined optimization method for common rail diesel engines. In: ASME 2002 Internal Combustion Engine Division spring technical conference:design, operation, and application of modern internal combustion engines and associated systems, Rockford, Illinois, USA, 14–17 April 2002, paper ICES2002-470, pp. 243–250. New York: ASME.
134.
NozakiYFukumaTTanakaK. Development of a rule-based calibration method for diesel engines. SAE paper 2005-01-0044, 2005.
135.
NatarajMArunachalamVPDhandapaniN. Optimizing diesel engine parameters for low emissions using Taguchi method: variation risk analysis approach – Part I. Indian J Engng Mater Sci2005; 12: 169–181.
136.
AtkinsonCMottG. Dynamic model-based calibration optimization: an introduction and application to diesel engines. SAE paper 2005-01-0026, 2005.
137.
BrooksTLumsdenGBlaxillH. improving base engine calibrations for diesel vehicles through the use of DoE and optimization techniques. SAE paper 2005-01-3833, 2005.
138.
RaskESellnauM. Simulation-based engine calibration: tools, techniques, and applications. SAE paper 2004-01-1264, 2004.
139.
HesselRPReitzRD. Diesel engine injection rate-shape optimization using genetic algorithms and multi-dimensional modeling for a range of operating modes. In: 11th international multidimensional engine modeling user’s group meeting, Detroit, Michigan, USA, 3 March 2002.
140.
SenecalPKReitzRD. Optimization of diesel engine emissions and fuel efficiency using genetic algorithms and computational fluid dynamics. In: 8th international conference on liquid atomization and spraying systems, Pasadena, California, USA, 16–20 July 2000, pp. 1–8.
141.
HiroyasuTNakayamaSMikiM. Comparison study of SPEA2+, SPEA2, and NSGA-II in diesel engine emissions and fuel economy problem. In: 2005 IEEE congress on evolutionary computation, Edinburgh, UK, 5 September 2005, Vol 1, pp. 236–242. New York: IEEE.
142.
TannerFXSrinivasanS. CFD-based optimization of fuel injection strategies in a diesel engine using an adaptive gradient method. Appl Mathl Modelling2009; 33: 1366–1385.
143.
OmranRYounesRChampoussinJC. Genetic algorithm for dynamic calibration of engine’s actuators. SAE paper 2007-01-1079, 2007.
144.
MalikopoulosAAAssanisDNPapalambrosPY. Real-time self-learning optimization of diesel engine calibration. Trans ASME, J Engng Gas Turbines Power2009; 131(2): 022803.
145.
WangJ. Air fraction estimation for multiple combustion mode diesel engines with dual-loop EGR systems. Control Engng Practice2008; 16: 1479–1486.
146.
UpadhyayDUtkinV IRizzoniG. Multivariable control design for intake flow regulation of diesel engine using sliding mode. In: 15th Triennial World Congress, Barcelona, Spain, 21–26 July 2002: IFAC.
