The effects of manufacturing tolerances on the maximum focal temperature has been investigated by transient thermomechanical simulations. Both relative cone angle and cone out-of-roundness for molybdenum and carbon fibre reinforced polymer synchronizers were evaluated. It was shown that cone out-of-roundness significantly increases the focal contact temperature for that specific cone but has little impact on the opposing cone. Two populations of measured synchronizers were evaluated, and it was shown that the maximum focal surface temperature can be decreased in almost all tolerance cases by introducing a relative angle between the cones.
SocinRWaltersK.Manual transmission synchronizers. SAE technical paper 680008, 1968.
2.
HäggströmD.On synchronization of heavy truck transmissions. Licentiate Thesis, KTH Royal Institute of Technology, Stockholm, 2016.
3.
HäggströmDSellgrenUBjörklundS.Evaluation of synchronizer loading parameters and their ability to predict failure. Proc IMechE, Part J: J Engineering Tribology2018; 232: 1093–1104.
4.
BarberJ.Thermoelastic instabilities in the sliding of conforming solids. Wear1970; 15: 296–296.
5.
YiYBDuSBarberJ, et al. Effect of geometry on thermoelastic instability in disk brakes and clutches. J Tribol1999; 121: 661–666.
6.
KinugasaTIshiiHShozakiH, et al. Thermal analysis of the synchronizer friction surface and its application to the synchronizer durability improvement. JSAE Rev1999; 20: 217–222.
7.
LöscheTPalandEGPollG. Wear behaviour of synchronisers in relation to a duty parameter. In: FlamandLDalmazGDowsonD, et al. (eds) Tribology for energy conservation, Vol. 34. Tribology Series. Amsterdam: Elsevier, 1998, pp.95–102.
8.
PollGSpreckelsM.Influence of temperature distribution on the tribological performance of automotive synchronisers. Tribology S2003; 41: 613–621.
9.
NeudörferS.Thermomechanische Einflüsse auf die Tribologie von Synchronisierungen. PhD Thesis, Gottfried Wilhelm Leibniz Universität, Hannover, 2008.
10.
AcunerRVölkelKPflaumH, et al. Influence of cone-angle-difference on performance of synchronizers with carbon friction linings. In: VDI-Berichte 2218. Friedrichshafen: VDI Wissensforum GmbH (ed), pp.595–610.
11.
HäggströmDSellgrenUBjörklundS.The effect of manufacturing tolerances on the thermomechanical load of gearbox synchronizers. Proc CIRP2018; 72: 1202–1207.
12.
BarkerK.The effect of separator flatness on the performance and durability of wet friction clutches. SAE technical paper930915, 1993.
13.
ZagrodzkiPTrunconeSA.Generation of hot spots in a wet multidisk clutch during short-term engagement. Wear2003; 254: 474–491.
14.
ISO 1101:2017. Geometrical product specifications (GPS) – geometrical tolerancing – tolerances of form, orientation, location and run-out.
15.
HäggströmDStenströmWSellgrenU, et al. Parameter study of the thermomechanical performance of heavy duty synchronizers. In: 15th international VDI Congress–drivetrain for commercial vehicles 2015, Friedrichshafen, 16–17 June 2015.
16.
HäggströmDStenströmWSellgrenU, et al. A verified and validated model for simulation-driven design of heavy duty truck synchronizers. In: ASME 2015 power transmission and gearing conference, Boston, MA, 2–5 August 2015. New York: ASME.
17.
HäggströmDSellgrenUBjörklundS. Determination of thermomechanical material properties of CFRP friction linings for gearbox synchronizers. Submitted for review 2018.
