Experimental investigation of the water–injected process-gas screw compressor

Abstract

The test rig for water-injected process-gas screw compressor is designed and established. The dry gas seal technology was adopted for the shaft seal of screw compressor and the test rig has the function of regulating and controlling the mass flow of injected water. The performance characteristics of process-gas screw compressor under different working conditions are investigated by experimental research. The effect of rotational speed, the injected water mass flow, and the discharge pressure on the performance of screw compressor including discharge temperature and power consumption were obtained. The experimental results show that the water injection could reduce the discharge temperature of compressor significantly and increase the capacity of screw compressor at the same time. There exists an optimum mass flow of injected water that could effectively reduce the discharge temperature and seal the clearance between the female and male rotor simultaneously. For the tested screw compressor prototype, the proper injected water-to-air mass ratio is about 2–3 L/m³. The additional power consumption caused by the injected water is small compared with the total shaft power. The established compressor test rig and the experimental results are helpful for the development and improvement on the performance of water-injected process-gas screw compressor.

Keywords

Process-gas screw compressor water injection characteristics performance experimental study

Get full access to this article

View all access options for this article.

References

Xing

. Screw compressor – therory, design and application, Beijing, China: China Machine Press, 2000. (in Chinese).

Ohama T, Kurioka Y, Tanake H, et al. Process gas applications where API 619 screw compressors replaced reciprocating and centrifugal compressors. In: Proceedings of the 35th turbomachinery symposium, Houston, TX ,USA, 25–28 September 2006, pp.89–96.

Ibragimov

Kalmykov

Khisameev

et al.

Water injection screw compressors in chemical plants. Chem Petrol Eng 2002; 38: 529–531.

Lelgemann

. The design, selection, and application of oil-free screw compressors for fuel gas service. J Eng Gas Turbine Power 1995; 117: 74–80.

Wennemar J. Dry screw compressor performance and application range. In: Proceedings of the 38th turbomachinery symposium, Houston, TX, USA, 14–17 September 2009, pp.149–156.

Jianfeng

Huagen

Bingming

et al.

Research on the performance of water-injection twin screw compressor. Appl Therm Eng 2009; 29: 3401–3408.

Ous

Mujic

Stosic

. Experimental investigation on water-injected twin-screw compressor for fuel cell humidification. Proc IMechE, Part C: J Mechanical Engineering Science 2012; 226: 2925–2932.

Almasi

. Oil-flooded screw compressor for coal seam gas applications. Proc IMechE, Part E: J Process Mechanical Engineering 2011; 226: 250–255.

Yong K. Calculations of the heat and mass transfer in reciprocating compressor with spraying water into cylinders. In: 9th International compressor engineering conference at Purdue, Purdue, USA, 18–21 July 1988, pp.472–476.

10.

Coney MW, Stephenson P, Malmgren A, et al. Development of a reciprocating compressor using water injection to achieve quasi-isothermal compression. In: 16th International compressor engineering conference at Purdue, Purdue, USA, 16–19 July 2002. Paper no. C4-3.

11.

Bracco

Pierfederici

Trucco

. The wet compression technology for gas turbine power plants: thermodynamic model. Appl Therm Eng 2007; 27: 699–704.

12.

Kim

Perez-Blanco

. Analytical modeling of wet compression of gas turbine systems. Appl Therm Eng 2011; 31: 834–840.

13.

White

Meacock

. An evaluation of the effects of water injection on compressor performance. J Eng Gas Turbine Power 2004; 126: 748–754.

14.

Roumeliotis

Mathioudakis

. Evaluation of interstage water injection effect on compressor and engine performance. J Eng Gas Turbine Power 2006; 128: 849–856.

15.

Zheng

Sun

et al.

Thermodynamic analyses of wet compression process in the compressor of gas turbine. J Turbomach 2003; 125: 489–496.