Experimental studies on graphite powder-mixed electro-discharge machining of Inconel 718 super alloys: Comparison with conventional electro-discharge machining

Abstract

Inconel 718 is a nickel-based super alloy widely applied in aerospace, automotive, and defense industries. Low thermal conductivity, extreme high temperature strength, strong work-hardening tendency make the alloy difficult-to-cut. In contrast to traditional machining, nonconventional route like electro-discharge machining is relatively more advantageous to machine this alloy. However, low thermal conductivity of Inconel 718 restricts electro-discharge machining from performing well. In order to improve the electro-discharge machining performance of Inconel 718, powder-mixed electro-discharge machining was reported in this paper. It was carried out by adding graphite powder to the dielectric media in consideration with varied peak discharge current. The morphology and topographical features of the machined surface including surface roughness, crack density, white layer thickness, metallurgical aspects (phase transformation, crystallite size, microstrain, and dislocation density), material migration, residual stress, microindentation hardness, etc. were studied and compared with that of the conventional electro-discharge machining. Additionally, effects of peak discharge current were discussed on influencing different performance measures of powder-mixed electro-discharge machining. Material removal efficiency and tool wear rate were also examined. Use of graphite powder-mixed electro-discharge machining was found to be better in performance for improved material removal rate, superior surface finish, reduced tool wear rate, and reduced intensity as well as severity of surface cracking. Lesser extent of carbon migration onto the machined surface as observed in powder-mixed electro-discharge machining in turn reduced the formation of hard carbide layers. As compared to the conventional electro-discharge machining, graphite powder-mixed electro-discharge machining exhibited relatively less microhardness and residual stress at the machined surface.

Keywords

Inconel 718 super alloy powder-mixed electro-discharge machining graphite powder dielectric media

Get full access to this article

View all access options for this article.

References

Special Metals Corporation: History, http://www.pccforgedproducts.com/brands/special_metals/products/high_performance_alloys/inconel/718/.

Ezugwu

Fadare

Bonney

et al.

Modelling the correlation between cutting and process parameters in high- speed machining of Inconel 718 alloy using an artificial neural network. Int J Mach Tools Manuf 2005; 45: 1375–1385.

Rajesha

Sharma

Kumar

. On electro-discharge machining of Inconel 718 with hollow tool. J Mater Eng Perform 2012; 21: 882–891.

Zhou

Bushlya

Peng

et al.

Analysis of subsurface microstructure and residual stresses in machined Inconel 718 with PCBN and Al₂O₃-SiC_w tools. Procedia CIRP 2014; 13: 50–155.

Amini

Fatemi

Atefi

. High speed turning of Inconel 718 using ceramic and carbide cutting tools. Arabian J Sci Eng 2014; 39: 2323–2330.

ASTE Handbook Committee. Tool engineers handbook, New York: McGraw Hill, 1950.

Geethapriyan

Kalaichelvan

Muthuramalingam

. Influence of coated tool electrode on drilling Inconel alloy 718 in electrochemical micro machining. Procedia CIRP 2016; 46: 127–130.

Lee

. Study of the effect of machining parameters on the machining characteristics in electrical discharge machining of tungsten carbide. J Mater Process Technol 2001; 115: 344–358.

Furutania

Saneto

Takezawa

et al.

Accretion of titanium carbide by electrical discharge machining with powder suspended in working fluid. Precis Eng 2001; 25: 138–144.

10.

Zhao

Meng

Wang

. The application of research on powder mixed EDM in rough machining. J Mater Process Technol 2002; 129: 30–33.

11.

et al.

Influence of flushing on performance of EDM with bunched electrode. Int J Adv Manuf Technol 2012; 58: 187–194.

12.

Tzeng

Lee

. Effects of powder characteristics on electro discharge machining efficiency. Int J Adv Manuf Technol 2001; 17: 586–592.

13.

Kansal

Singh

Kumar

. Parametric optimization of powder mixed electrical discharge machining by response surface methodology. J Mater Process Technol 2005; 169: 427–436.

14.

Peças

Henriques

. Electrical discharge machining using simple and powder-mixed dielectric: The effect of the electrode area in the surface roughness and topography. J Mater Process Technol 2008; 200: 250–258.

15.

Peças

Henriques

. Effect of the powder concentration and dielectric flow in the surface morphology in electrical discharge machining with powder-mixed dielectric (PMD-EDM). Int J Adv Manuf Technol 2008; 37: 1120–1132.

16.

Kung

K-Y

Horng

J-T

Chiang

K-T

. Material removal rate and electrode wear ratio study on the powder mixed electrical discharge machining of cobalt-bonded tungsten carbide. Int J Adv Manuf Technol 2009; 40: 95–104.

17.

Jahan

Rahman

Wong

. Study on the nano-powder-mixed sinking and milling micro-EDM of WC-Co. Int J Adv Manuf Technol 2011; 53: 167–180.

18.

Kumar

Batra

. Surface modification of die steel materials by EDM method using tungsten powder-mixed dielectric. J Manuf Process 2012; 14: 35–40.

19.

Bhattacharya

Batish

Singh

et al.

Optimal parameter settings for rough and finish machining of die steels in powder-mixed EDM. Int J Adv Manuf Technol 2012; 61: 537–548.

20.

Singh

Yeh

. Optimization of abrasive powder mixed EDM of aluminum matrix composites with multiple responses using gray relational analysis. J Mater Eng Perform 2012; 21: 481–491.

21.

Mai

Hocheng

Huang

. Advantages of carbon nanotubes in electrical discharge machining. Int J Adv Manuf Technol 2012; 59: 111–117.

22.

Bai

Zhang

Q-H

Yang

T-Y

et al.

Research on material removal rate of powder mixed near dry electrical discharge machining. Int J Adv Manuf Technol 2013; 68: 1757–1766.

23.

Prihandana

Sriani

Mahardika

et al.

Application of powder suspended in dielectric fluid for fine finish micro-EDM of Inconel 718. Int J Adv Manuf Technol 2014; 75: 599–613.

24.

Kolli

Kumar

. Effect of Boron Carbide powder mixed into dielectric fluid on electrical discharge machining of Titanium alloy. Procedia Mater Sci 2014; 5: 1957–1965.

25.

Singh

Kumar

Singh

. Effect of the addition of conductive powder in dielectric on the surface properties of super alloy Super Co 605 by EDM process. Int J Adv Manuf Technol 2015; 77: 99–106.

26.

Razak

Abdul-Rani

Nanimina

. Improving EDM efficiency with Silicon Carbide powder-mixed dielectric fluid. Int J Mater Mech Manuf 2015; 3: 40–43.

27.

Kumar

. Development of mirror like surface characteristics using nano powder mixed electric discharge machining (NPMEDM). Int J Adv Manuf Technol 2015; 76: 105–113.

28.

Batish

Bhattacharya

Kumar

. Powder mixed dielectric: an approach for improved process performance in EDM. Particul Sci Technol 2015; 33: 150–158.

29.

Singh

Kumar

. Influences of process parameters on MRR improvement in simple and powder-mixed EDM of AA6061/10%SiC composite. Mater Manuf Process 2015; 30: 303–312.

30.

Al-Khazraji

Amin

Ali

. The effect of SiC powder mixing electrical discharge machining on white layer thickness, heat flux and fatigue life of AISI D2 die steel. Eng Sci Technol 2016; 19: 1400–1415.

31.

Ekmekci

. Electrical discharge machining of Ti-6Al-4V in hydroxyapatite powder mixed dielectric liquid. Mater Manuf Process 2016; 31: 1663–1670.

32.

Kuriachen

Mathew

. Effect of powder mixed dielectric on material removal and surface modification in microelectric discharge machining of Ti-6Al-4V. Mater Manuf Process 2016; 31: 439–446.

33.

Baseri

Sadeghian

. Effects of nanopowder TiO2-mixed dielectric and rotary tool on EDM. Int J Adv Manuf Technol 2016; 83: 519–528.

34.

Prabhu

Vinayagam

. Optimization of carbon nanotube based electrical discharge machining parameters using full factorial design and genetic algorithm. Aust J Mech Eng 2016; 14: 161–173.

35.

Zhao

et al.

Surface characteristics of Ti-6Al-4V by SiC abrasive-mixed EDM with magnetic stirring. Mater Manuf Process 2017; 32: 83–86.

36.

Prakash

Kansal

Pabla

et al.

Experimental investigations in powder mixed electric discharge machining of Ti–35Nb–7Ta–5Zrβ-titanium alloy. Mater Manuf Process 2017; 32: 274–285.

37.

Talla

Gangopadhyay

Biswas

. Effect of impregnated powder materials on surface integrity aspects of Inconel 625 during electrical discharge machining. Proc IMechE, Part B: J Engineering Manufacture 2018; 232: 1259–1272.

38.

Çaydaş

Hasçalık

. Optimization of micro-EDM drilling of Inconel 718 superalloy. Int J Adv Manuf Technol 2013; 66: 1015–1023.

39.

Rahul Abhishek

Datta

Biswal

et al.

Machining performance optimization for electro discharge machining of Inconel 601, 625, 718 and 825: An integrated optimization route combining satisfaction function, fuzzy inference system and Taguchi approach. J Brazil Soc Mech Sci Eng 2017; 39: 3499–3627.

40.

Upadhyay

Datta

Masanta

et al.

An experimental investigation emphasizing surface characteristics of electro-discharge machined Inconel 601. J Brazil Soc Mech Sci Eng 2017; 39: 3051–3066.

41.

Jahan

Rahman

Wong

. Modelling and experimental investigation on the effect of nanopowder-mixed dielectric in micro-electrodischarge machining of tungsten carbide. Proc IMechE, Part B: J Engineering Manufacture 2010; 224: 1725–1739.

42.

Muthuramalingam

Mohan

Jothilingam

. Effect of tool electrode resolidification on surface hardness in electrical discharge machining. Mater Manuf Process 2014; 29: 1374–1380.

43.

Wong

Lin

Rahuman

et al.

Near-mirror-finish phenomenon in EDM using powder-mixed dielectric. J Mater Process Technol 1998; 79: 30–40.

44.

Kozak

Rozenek

Dabrowski

. Study of electrical discharge machining using powder-suspended working media. Proc IMechE, Part B: J Engineering Manufacture 2004; 217: 1597–1602.

45.

Chow

Yan

Huang

et al.

Study of added powder in kerosene for the micro-slit machining of Titanium alloy using electro-discharge machining. J Mater Process Technol 2000; 101: 95–103.