Effect of nanofiller on fibre laser drilling quality of carbon fibre reinforced polymer composite laminates

Abstract

Laser machining of carbon fibre reinforced polymer composites is a challenging task due to a significant difference between physical and thermal properties of the constituent materials, i.e. polymer matrix and carbon fibres. This results in extended heat-affected zone (HAZ), taper kerf and poor surface finishing. This paper focuses on an investigation, attempting to minimise the divergence in the decomposition temperature of carbon fibres and epoxy resin by adding multi-walled carbon nanotubes in polymer matrix as a secondary reinforcement. High thermal conductivity of multi-walled carbon nanotubes increases the thermal diffusivity of polymer matrix, which in turn reduces the matrix recession. In addition, laser power and scan speed was also considered as an input parameter and their influence on output responses such as HAZ, taper angle and surface roughness has been studied. To analyse the effect of multi-walled carbon nanotubes on the resultant thermal damage, an innovative technique, i.e. scanning acoustic microscopy was used. This technique provides a ply-by-ply damage analysis. C-scans of the top and bottom surface of the machined holes in the composite were also carried out. Further, micrographs of the holes were taken to analyse the quality of the holes using field-emission scanning electron microscope. The obtained results indicated that HAZ, taper angle and surface roughness of holes decreased by ∼30%, ∼47% and ∼43%, respectively, with 1.5 wt% multi-walled carbon nanotubes doped carbon fibre reinforced polymer laminates, when compared with the results obtained from experiments with neat carbon fibre reinforced polymer composite laminates.

Keywords

Fibre laser drilling carbon fibre reinforced polymer multi-walled carbon nanotubes HAZ taper angle surface roughness

Get full access to this article

View all access options for this article.

References

Abrao

Faria

Campos Rubio

et al.

Drilling of fibre reinforced plastics: a review. J Mater Process Technol 2007; 186: 1–7.

Liu

Tang

Cong

. A review of mechanical drilling for composite laminates. Compos Struct 2012; 94: 1265–1279.

Kumar

Singh

. An approach towards damage free machining of CFRP and GFRP composite material: a review. Adv Compos Mater 2014; 24: 49–63.

Kumar

Singh

Zitoune

. Experimental investigation of delamination and surface roughness in the drilling of GFRP composite material with different drills. Adv Manuf: Polym Compos Sci 2016; 2: 47–56.

Salama

Mativenga

et al.

TEA CO2 laser machining of CFRP composite. Appl Phys A 2016; 122: 497–516.

Salama

Mativenga

et al.

High-power picosecond laser drilling/machining of carbon fibre-reinforced polymer (CFRP) composites. Appl Phys A 2016; 122: 73–83.

Cadorin

Zitoune

Seitier

et al.

Analysis of damage mechanism and tool wear while drilling of 3D woven composite materials using internal and external cutting fluid. J Compos Mater 2014; 49: 2687–2703.

Zitoune

El Mansori

Krishnaraj

. Tribo-functional design of double cone drill implications in tool wear during drilling of copper mesh/CFRP/woven ply. Wear 2013; 302: 1560–1567.

Haddad

Zitoune

Bougherara

et al.

Study of trimming damages of CFRP structures in function of the machining processes and their impact on the mechanical behaviour. Compos Part B: Eng 2014; 57: 136–143.

10.

Saoudi

Zitoune

Gururaja

et al.

Prediction of critical thrust force for exit-ply delamination during drilling composite laminates: thermo-mechanical analysis. Int J Mach Mach Mater 2016; 18: 77–98.

11.

Cadorin

Zitoune

. Wear signature on hole defects as a function of cutting tool material for drilling 3D interlock composite. Wear 2015; 742: 332–333.

12.

Saleem

Toubal

Zitoune

et al.

Investigating the effect of machining processes on the mechanical behaviour of composite plates with circular holes. Compos Part A: Appl Sci Manuf 2013; 55: 169–177.

13.

Okutan

Karabay

Sinmazcelik

et al.

A study on the derivation of parametric cutting force equations in drilling of GFRP composites. J Mech Eng 2012; 59: 97–105.

14.

Dubey

Yadav

. Laser beam machining—a review. Int J Mach Tool Manuf 2008; 48: 609–628.

15.

Kim

Lee

. A study of ultrasonic vibration cutting of carbon fibre reinforced plastics. Int J Adv Manuf Technol 1996; 12: 78–86.

16.

Toenshoff HK, Alvensleben FV, Heekenjann PB, et al. Excimer laser machining of advanced materials. In: Proceeding of the SPIE – The International Society for Optical Engineering, 1997, pp. 108–118.

17.

Negarestani

. Fibre laser cutting of carbon fibre reinforced polymeric composites. Pro-c IMechE, Part B: J Engineering Manufacture 2013; 227: 1755–1766.

18.

Caprino

Tagliafferi

. Maximum cutting speed in laser cutting of fibre reinforced plastics. Int J Mach Tool Manuf 1988; 28: 389–398.

19.

Muramatsu

Harada

Suzuki

et al.

Infrared stress measurements of thermal damage to laser-processed carbon fibre reinforced plastics. Compos Part A: Appl Sci Manuf 2015; 68: 242–250.

20.

Tagliafferi

Di Ilio

Visconti

. Laser cutting of fibre reinforced polyesters. Composites 1985; 16: 317–325.

21.

Powell

. CO2 laser cutting, London: Springer, 1998.

22.

Yung

WKC

Yue

et al.

Nd:YAG laser drilling in epoxy resin/AlN composites material. Compos Part-A: Appl Sci Manuf 2007; 38: 2055–2064.

23.

Nagesh

Murthy

HNN

Krishna

et al.

Parametric study of CO2 laser drilling of carbon nanopowder/vinylester/glass nanocomposites using design of experiments and grey relational analysis. Optics Laser Technol 2013; 48: 480–488.

24.

Al-Sulaiman

Yilbas

Ahsan

. CO2 laser cutting of carbon/carbon multi-lamelled plain-weave structure. J Mater Process Technol 2006; 173: 345–351.

25.

Yue

Lau

. Pulsed Nd:YAG laser cutting of Al/Li/SiC metal matrix composites. Mater Manuf Process 1996; 11: 17–29.

26.

Kumar D, Singh KK and Zitoune R. Impact of carbon nanotubes reinforcement in glass/epoxy polymeric nanocomposite on the quality of fiber laser drilling. Proc IMechE, Part B: J Engineering Manufacture 2018. DOI: https://doi.org/10.1177/0954405417703426.

27.

Leone

Genna

Tagliaferri

. Fibre laser cutting of CFRP thin sheet by multi-passes scan technique. Optics Lasers Eng 2014; 53: 43–50.

28.

Herzog

Jaeschke

Meier

et al.

Investigations on the thermal effect caused by laser cutting with respect to static strength of CFRP. Int J Mach Tools Manuf 2008; 48: 1464–1473.

29.

Ilio

Tagliaferri

Veniali

. Machining parameters and cut quality in laser cutting of ara-mid fibre reinforced plastics. Mater Manuf Process 1990; 5: 591–608.

30.

Takahashia

Tsukamoto

Masuno

et al.

Influence of laser scanning conditions on CFRP processing with a pulsed fibre laser. J Mater Process Technol 2015; 222: 110–121.

31.

Kalyanasundaram

Shehata

Neumann

et al.

Design and validation of a hybrid laser/water-jet machining system for brittle materials. J Laser Appl 2008; 20: 127–134.

32.

Nagesh

Murthy

HNN

Krishna

et al.

Influence of nanofillers on the quality of CO2 laser drilling in vinylester/glass using orthogonal array experiments and grey relational analysis. Optics Laser Technol 2015; 69: 23–33.

33.

Riveiro

Quintero

Lusquinos

et al.

Experimental study on the CO2 laser cutting of carbon fibre reinforced plastic composite. Compos Part A: Appl Sci Manuf 2012; 43: 1400–1409.

34.

Hejjaji

Singh

Kubher

et al.

Machining damage in FRPs: Laser versus conventional drilling. Compos Part A: Appl Sci Manuf 2016; 82: 42–52.

35.

Islam

. An investigation into CO2 laser trimming of CFRP and GFRP composites. Procedia Eng 2013; 63: 931–937.

36.

Martin-Gallego

Verdejo

Khayet

et al.

Thermal conductivity of carbon nanotubes and graphene in epoxy nanofluids and nanocomposites. Nanoscale Res Lett 2011; 6: 610–615.