This study investigated the effects of Deep Cryogenic Treatment (DCT) on machinability, hardness, and microstructure in dry turning process of AISI 4140 (48-51 HRc) tempered steels with ceramic cutting tools on the surface roughness (Ra). DCT process of steels has shown significant improvement in their mechanical properties. In this context, experiments were made with Taguchi L16 method and optimum values were determined. Three different values for each control factors as: different heat treated samples, cutting speeds (160, 200, 240, 280 m/min), feed rates (0.08, 0.12, 0.16, 0.20 mm/rev) were selected. As a result, the lowest Ra value was found to be 0.159 µm for the DCTT36 sample at a cutting speed of 240 m/min, a feed rate of 0.08 mm/rev. The optimum Ra value was the lowest for the DCTT36 sample compared to the other samples as 0.206 µm. The hardness values of the micro and macro were highest for the DCTT36 sample. Microstructural point of view Scanning Electron Microscopy (SEM) point of view, the DCCT36 sample showed that best results owing to its homogeneity. It was concluded that lower Ra values can be obtained with ceramic cutting tool in dry turning experiments according to the studies in the literature review. It is thought to be preferred as an alternative to cylindrical grinding process due to lower cost.
KamM.Experimental analysis of cryogenic treated shafts dynamic behaviors. PhD Thesis, Department of Mechanical Engineering, Graduate School of Natural and Science, Duzce University, Düzce, Turkey, 2016.
2.
KamMSaruhanH.Experimental vibration analysis of cryogenic treated shafts supported by journal and rolling element bearings. J Polytechnic2019;
22: 129–134.
3.
DemirZ,AdiyamanO.Investigation of influence of approach angle and chip slenderness ratio on vibration, chip formation and surface quality in turning of AISI 1050 steel. J Braz Soc Mech Sci Eng2019;
41: 467.
4.
BilalMMYaqoobKZahidMH, et al.
Effect of austempering conditions on the microstructure and mechanical properties of AISI 4340 and AISI 4140 steels. J Mater Res Technol2019;
8: 5194–5200.
5.
VigneshK, PadmanabhanP.Analysis the residual stress of cutting tool insert in turning of mild steel – a review. Int J Adv Sci Technol2016;
90: 49–60.
6.
VishwakarmaA,JainS, Kumar SharmaP.Analysis of effect of minimum quantity lubrication on different machining parameters cutting force, surface roughness and tool wear by hard turning of AISI-4340 alloy steel – a review. Int J Adv Eng Res Technol2014;
2: 344–354.
7.
OzelTKarpatYFigueiraL, et al.
Modelling of surface finish and tool flank wear in turning of AISI D2 steel with ceramic wiper inserts. J Mater Process Technol2007;
189: 192–198.
8.
KaradenizE.Influence of different initial microstructure on the process of spheroidization in cold forging. Mater Des2008; 29: 251--256.
9.
ArivazhaganNSinghSPrakashS, et al.
An assessment of hardness, impact strength and hot corrosion behaviour of friction-welded dissimilar weldments between AISI 4140 and AISI 304. Int J Mach Tool Manuf2008;
39: 679–689.
10.
ZhengLZhengDZhaoL, et al.
Novel water-air circulation quenching process for AISI 4140 steel. Metals Mater Int2013;
19: 1373–1376.
11.
AydayADurmanM.Effect of different surface-heat-treatment methods on the surface properties of AISI 4140 steel.Mater Technol2014;
48: 787–790.
12.
MeysamiAHGhasemzadehRSeyedeinSH, et al.
An investigation on the microstructure and mechanical properties of direct-quenched and tempered AISI 4140 steel. Mater Des2010;
31: 1570–1575.
13.
SenthilkumarDRajendranIPellizzariM, et al.
Influence of shallow and deep cryogenic treatment on the residual state of stress of 4140 steel. J Mater Process Technol2011;
211: 396–401.
14.
SenthilkumarDRajendranI.Optimization of deep cryogenic treatment to reduce wear loss of 4140 steel. Mater Manuf Process2012;
27: 567–572.
15.
BenselyAPrabhakaranALalDM, et al.
Enhancing the wear resistance of case carburized steel (en 353) by cryogenic treatment. Cryogenics2005;
45: 747–754.
16.
ZhirafarS.Effect of cryogenic treatment on the mechanical properties of steel and aluminum alloys. Master’s Thesis, Concordia University, Montreal, 2005.
17.
ZhirafarSRezaeianAPughM.Effect of cryogenic treatment on the mechanical properties 4340 steel. J Mater Process Technol2007;
186: 298–303.
18.
SenthilkumarD.Effect of deep cryogenic treatment on residual stress and mechanical behaviour of induction hardened En 8 steel. Adv Mater Process Technol2016; 1: 10.
19.
SuhailAHIsmailNWongSV, et al.
Optimization of cutting parameters based on surface roughness and assistance of workpiece surface temperature in turning process. Am J Eng Appl Sci2010;
3: 102–108.
20.
LimaJGAvilaRFAbraoAM, et al.
Hard turning: AISI 4340 high strength low alloy steel and AISI D2 cold work tool steel. J Mater Process Technol2005;
169: 388–395.
21.
MandalNDoloiBMondalB.Machining parameters optimization of developed yttria stabilized zirconia toughened alumina ceramic ınserts while machining AISI 4340 steel. World Acad Sci Eng Technol2012;
6: 62–72.
22.
DasSRDhupalDKumarA.Experimental investigation into machinability of hardened AISI 4140 steel using TiN coated ceramic tool.Measurement2015;
62: 108–126.
23.
DasDDuttaAKRayKK.Optimization of the duration of cryogenic processing to maximize wear resistance of AISI D2 steel. Cryogenics2009;
49: 176–184.
24.
VahdatSENateghSMırdamadıS.Microstructure and tensile properties of 45WCrV7 tool steel after deep cryogenic treatment. Mater Sci Eng A2013;
585: 444–454.
25.
DasDDuttaAKRayKK.Sub-zero treatments of AISI D2 steel: part I. microstructure and hardness. Mater Sci Eng A2010;
527: 2182–2193.
26.
MasmiatiNSarhan AhmedAD.Optimizing cutting parameters in inclined end milling for minimum surface residual stress – Taguchi approach. Measurement2015;
60: 267–275.
27.
YücelE and SaruhanH.Design optimization of rotor-bearing system considering critical speed using Taguchi method. Proc IMechE, Part E: J Process Mechanical Engineering2017;
231: 138–146.
28.
GürbüzH.Investigation of cutting tool geometry andcoating types on surface integrity of AISI 316l steel. PhD Thesis, Department of Mechanical Education, Gazi University, Ankara, Turkey, 2012.
29.
GandariasALópez de LacalleLNAizpitarteX, et al.
Study of the performance of the turning and drilling of austenitic stainless steels using two coolant techniques. Int J Mach Mach Mater2008;
3: 1–17.
30.
YiJXueWXieJ, et al.
Enhanced toughness and hardness at cryogenic temperatures of silicon carbide sintered by SPS. Mater Sci Eng A2013;
569: 13–17.
31.
PreciadoMBravoPMAlegreJM.Effect of low temperature tempering prior cryogenic treatment on carburized steels.J Mater Process Technol2006;
176: 41–44.
32.
RhyimYMHanSHNaYS, et al.
Effect of deep cryogenic treatment on carbide precipitation and mechanical properties of tool steel, Solid State Phenomena2006;
118: 9–14.
33.
SinghSGSinghJSinghR, et al.
Effect of cryogenic treatment on AISI M2 high speed steel: metallurgical and mechanical characterization.J Mater Eng Perform2012;
21: 1320–1326.
34.
MolinariAPellizzariMGialanellaS, et al.
Effect of deep cryogenic treatment on the mechanical properties of tool steels.J Mater Process Technol2001;
118: 350–355.
35.
PellizzariMMolinariAGialanellaS, et al.
Effetto del trattamento criogenico sulle proprietà microstrutturali dell’acciaio AISI H13. La Metallurgia Italiana2001;
1: 21–27.
36.
YangHSWangJShenBL, et al.
Effect of cryogenic treatment on the matrix structure and abrasion resistance of white cast iron subjected to destabilization treatment.Wear2007;
261: 1150–1154.
37.
LiuHHWangJShenBL, et al.
Effects of deep cryogenic treatment on property of 3Cr13Mo1V1.5 high chromium cast iron.Mater Des2006;
28: 1059–1064.
38.
YunDXiaopingLHongshenX. Deep cryogenic treatment of high-speed steel and its mechanism.Heat Treat Met1998;
3: 55–59.
39.
BaldisseraPDelpreteC.Deep cryogenic treatment: a bibliographic review.Open Mech Eng J2008;
2: 1--11.
40.
PekgözBSarıdemirSUygurİ, et al.
Sementasyon işleminin farklı çeliklerin mikroyapı ve sertlik değerlerine etkileri.Makine Teknolojileri Elektronik Dergisi2013;
10: 19–24.
41.
ErdoğanM. Mühendislik alaşımlarının yapı ve özellikleri. Cilt 1. Ankara: Nobel yayın dağıtım Ltd., 2000, p.151.
