Effect of material combinations on mechanical properties of flat bottom riveted joint

Abstract

Flat bottom riveting is a newly developed joining technique. Since the bottom surface of joint is flat, the joint can be applied in areas that need a high degree of smoothness. This article investigated the effect of material combinations on mechanical properties of joints. Four material combinations which involved two kinds of aluminum alloy were produced. Cross sections of joints were observed by metallographic microscope and geometrical parameters of joints were measured. It was found that material combinations exerted significant influence on the geometrical parameters of joints. When the bottom sheet remained the same, with the increase of top sheet hardness, the interlock thickness of joint decreased, while the neck thickness of joint increased. Tensile and shearing tests were conducted on joint to obtain the tensile load and the shearing load of joint. The absorbed energy of joint in shearing test was calculated. Results showed that when joining materials with different hardness values, the joint with high hardness sheet on the top exhibited higher static load than the joint with high hardness sheet on the bottom. In tensile tests, 1060–5052 joint failed in the manner of neck fracture, while other joints failed in the manner of button separation. In shearing tests, 5052–1060 joint failed in the manner of button separation, while other joints failed in the manner of neck fracture.

Keywords

Material combinations flat bottom riveting aluminum alloy rigid rivet

Get full access to this article

View all access options for this article.

References

J-l

X-j

, et al. Dislocation density model and microstructure of 7A85 aluminum alloy during thermal deformation. Journal of Central South University 2021; 28: 2999–3007.

Wei

Feng

Zhang

, et al. Influence of aging on microstructure, mechanical properties and stress corrosion cracking of 7136 aluminum alloy. Journal of Central South University 2021; 28: 2687–2700.

Lin

. Clinching process for aluminum alloy and carbon fiber-reinforced thermoplastic sheets. The International Journal of Advanced Manufacturing Technology 2018; 97: 529–541.

Wang

, et al. An experimental and numerical study on laser shock clinching for joining copper foil and perforated stainless steel sheet. J Mater Process Technol 2018; 258: 155–164.

Song

Yang

Zhu

, et al. Numerical and experimental study on failure behavior of steel-aluminium mechanical clinched joints under multiple test conditions. International Journal of Lightweight Materials and Manufacture 2019; 2: 72–79.

Lei

Xing

, et al. Effect of foam copper interlayer on the mechanical properties and fretting wear of sandwich clinched joints. J Mater Process Technol 2019; 274: 116285.

Ren

Chen

Qin

, et al. Mechanical properties of tubular rivet-reinforced joints realized with different reinforcing loads. The International Journal of Advanced Manufacturing Technology 2021; 117: 877–888.

Ren

X-q

Chen

Ran

X-k

, et al. Microstructure evolution of AA5052 joint failure process and mechanical performance after reconditioning with tubular rivet. Transactions of Nonferrous Metals Society of China 2021; 31: 3380–3393.

Xian

Shan

, et al. Single-sided joining of aluminum alloys using friction self-piercing riveting (F-SPR) process. J Manuf Process 2019; 38: 319–327.

10.

Han

Thornton

, et al. Influence of edge distance on quality and static behaviour of self-piercing riveted aluminium joints. Mater Des 2012; 34: 22–31.

11.

Bouchard

Laurent

Tollier

. Numerical modeling of self-pierce riveting—from riveting process modeling down to structural analysis. J Mater Process Technol 2008; 202: 290–300.

12.

Lou

, et al. Effect of rivet and die on self-piercing rivetability of AA6061-T6 and mild steel CR4 of different gauges. J Mater Process Technol 2018; 251: 282–294.

13.

Liu

Zhuang

. Self-piercing riveted-bonded hybrid joining of carbon fibre reinforced polymers and aluminium alloy sheets. Thin-Walled Struct 2019; 144: 106340.

14.

Jiang

Sun

Liang

, et al. Shear failure behavior of CFRP/Al and steel/Al electromagnetic self-piercing riveted joints subject to high-speed loading. Compos Struct 2019; 230: 111500.

15.

Jiang

Gao

, et al. Structural design of half hollow rivet for electromagnetic self-piercing riveting process of dissimilar materials. Mater Des 2019; 183: 108141.

16.

Liang

Jiang

Zhang

, et al. Investigations on mechanical properties and microtopography of electromagnetic self-piercing riveted joints with carbon fiber reinforced plastics/aluminum alloy 5052. Archives of Civil and Mechanical Engineering 2019; 19: 240–250.

Supplementary Material

Please find the following supplemental material available below.

For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.

For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.

0.00 MB

3.73 MB