This paper compares the tribological behaviour of microalloyed rail steel with conventional C–Mn rail steel under different test conditions (load, temperature and humidity). Pin-on-disc tribological tests were performed inside a climate chamber under different loads (20, 30 and 40 N), relative humidity (15, 55 and 70%) and temperatures (20 and 40 ℃). After the friction and wear tests, the worn surfaces were analysed using both confocal and scanning electron microscopies. The results obtained show that the use of microalloyed steel in railway applications under severe conditions (high loads and humidity) could lead to increased service life of the rails and could extend the time between maintenance operations.
WangJZhouHShiYet al.Mechanical properties and fracture toughness of rail steels and thermite welds at low temperature. Int J Miner Metall Mater2012; 19: 409–420.
2.
Perez-UnzuetaAJBeynonJ. Microstructure and wear resistance of perlitic steel rails. Wear1993; 162: 173–182.
3.
OrdóñezRGarcíaCIArdoaAet al.Advanced metallurgical alloy design and thermomechanical processing for steel rails for North American heavy haul use. Wear2011; 274: 364–373.
4.
PandaBBalasubramaniamRVajpeiACet al.Characterization of rust on microalloyed steel rail exposed to coastal location in India. Eng Sci Technol2009; 44: 275–279.
5.
PandaBBalasubramaniamRMoonA. Microstructure and mechanical properties of novel steel rails. Mater Sci Technol2009; 25: 1375–1382.
6.
MoonAPBalasubramaniamRPandaB. Hydrogen embrittlement of microalloyed steel rails. Mater Sci Eng2010; 527: 3259–3263.
7.
RamalhoAEstevesMMartaP. Friction and wear behavior of rolling–sliding steel contacts. Wear2013; 302: 1468–1480.
8.
AniołekKHerianJ. The structure, properties and a resistance to abrasive wear of railway sections of steel with different pearlite morphology. IOP Conf Ser Mater Sci Eng2011; 22: 012012–012012.
9.
EN 13674-1: 2011. Railway applications – Track – Rail – Part 1: vignole railway rails 46 kg/m and above, 28 February 2011.
10.
American Railway Engineering and Maintenance-of-Way Association (AREMA). Manual for Railway Engineering Volume 1. Track. Chapter 4. Rail, 2013.
11.
JungwonSSeokjinKDeonghyeongL. Effects of surface defects on rolling contact fatigue of rail. Procedia Eng2011; 10: 1274–1278.
12.
GarnhamJEDavisCL. Very early stage rolling contact fatigue crack growth in pearlitic rail steels. Wear2011; 27: 100–112.
13.
OzsaracUAslanlarS. Wear behavior investigation of wheel/rail interface in water lubrication and dry friction. Ind Lubricat Tribol2008; 60: 101–107.
WindartaBaharomMB. Experimental prediction of wear rate on rail and wheel materials at dry sliding contact. MATEC Web Conf2014; 13: 3–13.
16.
WangWJGuoHMDuXet al.Investigation on the damage mechanism and prevention of heavy-haul railway rail. Eng Failure Anal2013; 35: 206–218.
17.
ZhongWHuJJShenPet al.Experimental investigation between rolling contact fatigue and wear of high-speed and heavy-haul railway and selection of rail material. Wear2011; 271: 2485–2493.
18.
WindartaMBSudinKF. Influence of applied load on wear characterizations of rail material. J Appl Sci2011; 11: 1636–1641.
19.
BakowskiHPosmykAKrawczykJ. Tribological properties of rail steel in straight moderately loaded sections of railway tracks. Arch Metall Mater2011; 56: 813–822.
20.
MeehanPABellettePAHorwoodRJ. Does god play dice with corrugations? Environmental effects on growth. Wear2014; 314: 254–260.
21.
Ishida M, Aoki F, Sone Y, et al. Rail corrugations caused by low coefficient of friction in a submarine railway tunnel. In: Proceedings of the World Tribology Congress III, Washington, DC, USA, 12–16 September 2005, pp.931–932.
22.
LewisSLewisROlofssonUet al.Effect of humidity, temperature and railhead contamination on the performance of friction modifiers: pin-on-disk study. Proc IMechE, Part F: J Rail and Rapid Transit2013; 227: 115–127.
23.
ZhuYOlofssonUChenH. Friction between wheel and rail: a pin-on-disc study of environmental conditions and iron oxides. Tribol Lett2013; 52: 327–339.
24.
LyuYZhuYOlofssonU. Wear between wheel and rail: a pin-on-disc study of environmental conditions and iron oxides. Wear2015; 329: 277–285.
25.
González Fueyo JL. Influencia de la microestructura en el comportamiento mecánico de aceros utilizados en la fabricación de carril. Thesis, University of Oviedo, Spain, 1997.
26.
DIN 50602. Microscopic examination of special steels using standard diagrams to assess the content of non-metallic inclusions, 1 September 1985.
27.
ASTM G99-17: standard test method for wear testing with a pin-on-disk apparatus, 1 January 2017.
28.
WindartaMSudinBBaharomMB. Prediction of contact temperature on interaction between rail and wheel materials using pin-on-disc method. J Appl Sci2012; 12: 2424–2429.
29.
ViáfaraCCCastroMIVélezJMet al.Unlubricated sliding wear of pearlitic and bainitic steels. Wear2005; 259: 405–411.
QiJZhuWYangCet al.MnS inclusion behaviour in heavy rail steel during heating process. Heat Treat Metals2013; 38: 40–42.
32.
El-ShabasyABLewandowskiJJ. Effects of load ratio, R, and test temperature on fatigue crack growth of fully pearlitic eutectoid steel (fatigue crack growth of pearlitic steel). Int J Fatigue2004; 26: 305–309.
ArchardJFHirstW. Wear of metals under unlubricated conditions. Proc R Soc London Part A1956; 236: 3–55.
35.
LewisROlofssonU. Mapping rail wear regimes and transitions. Wear2004; 257: 721–729.
36.
DayotCSaulotAGodeauCet al.Tribological behaviour of pearlitic and bainitic steel grades under various sliding conditions. Tribol Int2012; 46: 128–136.
37.
TyfourWRBeynonJHKapoorA. The steady wear behavior of pearlitic steel rail under dry rolling–sliding contact conditions. Wear1995; 180: 79–89.
38.
SuzumuraJYasutomoSIshizakiAet al.In situ X-ray analytical study on the alteration process of iron oxide layers at the railhead surface while under railway traffic. Wear2011; 271: 47–53.
