Optimal profile design for rail grinding based on wheel–rail contact,stability,and wear development in high-speed electric multiple units

Abstract

High-speed electric multiple units have numerous advantages. However, a number of critical maintenance issues arise in the operation of high-speed electric multiple units. The previous researches about rail profile design usually take only a single type of wheel profile into account, which would cause some other problems such as severe increase of hollow wear on the wheels. This study systematically investigates the influence of rail grinding on running stability and wear development in high-speed electric multiple units and designs a new rail profile as reference for grinding that takes all types of vehicle wheels running on a specific line into account, in order to design a ground rail which could match the wheel profile and thus improve the running stability of electric multiple units. All types of wheel profiles used on the Wuhan–Guangzhou railway line are taken as the design reference. A wheel–rail wear simulation program is constructed based on CONTACT numerical simulation software and SIMPACK vehicle system dynamics software. The simulation results show that both the wheel–rail contact relationship and the running stability of high-speed electric multiple units improved after rail grinding. The results of the wheel wear analysis show that when the rail is ground to the target profile, after a running mileage of 200,000 km, the wear area of the new wheel profile LMA and the greatest hollow wear wheel profile LMA-25 decreases by 1.13 mm² and 9.86 mm², respectively. In addition, this method can prolong the wheel reprofiling interval. For the Wuhan–Guangzhou railway line, normally the grinding interval for the tangent track and large-radius curve is 2–3 years, and for the entering and exiting tunnel sections, the grinding interval should be set for 1–2 years, which could remove the damaged layer of the rail surface and could restore the designed profile of the rail and prolong the rail service life.

Keywords

High-speed electric multiple units wheel–rail contact rail grinding running stability hollow wear

Get full access to this article

View all access options for this article.

References

Xu K, Feng Z, Wu H, et al. Investigating the influence of rail grinding on stability, vibration, and ride comfort of high-speed EMUs using multi-body dynamics modelling. Veh Syst Dyn 2019; 57: 1621–1642.

Polach

Nicklisch

. Wheel/rail contact geometry parameters in regard to vehicle behaviour and their alteration with wear. Wear 2016; 366–367: 200–208.

Kuffa

Ziegler

Peter

, et al. A new grinding strategy to improve the acoustic properties of railway tracks. Proc IMechE, Part F: J Rail and Rapid Transit 2018; 232(1): 214–221.

Asplund M, Khan SA and Nordmark T. Improved wheel-rail system of Sweden's iron ore line. In: Proceedings of the 11th International Heavy Haul Association Conference, Cape Town, South Africa, 2–6 September 2017, pp.759–766.

Marich

. Rail grinding strategies adopted in Australia. Rail Eng Int 2005; 9: 4–6.

Sharma

. Positive results from rail grinding in India. IRJ 2004; 5: 41–44.

Persson

Nilsson

Bik

, et al. Use of a genetic algorithm to improve the rail profile on Stockholm underground. Veh Syst Dyn 2010; 48: 89–104.

Persson

Iwnicki

. Optimization of railway profiles using a genetic algorithm. Veh Syst Dyn 2004; 41: 517–527.

Choi

Lee

Song

, et al. Optimization of rail profile to reduce wear on curved track. Int J Precis Eng Manuf 2013; 14: 619–625.

10.

Cui

Jin

, et al. Study on rail goal profile by grinding. Eng Mech 2011; 28: 178–184.

11.

Xue

Cui

, et al. Parallel inverse design method of wheel profile. J Mech Eng 2013; 49: 8–16.

12.

Guo

. Study of rail grinding based on wheel rail creep minimization. China Railway Sci 2011; 32: 9–15.

13.

Magel

Kalousek

. Designing and assessing wheel/rail profiles for improved rolling contact fatigue and wear performance. Proc IMechE, Part F: J Rail and Rapid Transit 2017; 231(7): 805–818.

14.

Pieringer

Kropp

Nielsen

JCO

. The influence of contact modelling on simulated wheel/rail interaction due to wheel flats. Wear 2014; 314(1–2): 273–281.

15.

Polach

. Wheel profile design for target conicity and wide tread wear spreading. Wear 2011; 271: 195–201.

16.

Jin

Liu

. Tribology of wheel and rail, Beijing: China Railway Press, 2004.

17.

Alonso

Guiral

Baeza

, et al. Wheel–rail contact: Experimental study of the creep forces–creepage relationships. Veh Syst Dyn 2014; 52(Suppl. 1): 469–487.

18.

UIC 515-4: 1993. Passenger rolling stock – trailer bogies – running gear – bogie frame structure strength tests. Paris: UIC 515-4, 1993.

19.

UIC 518: 2009. Testing and approval of railway vehicles from the point of view of their dynamics behaviour–safety–track fatigue–running behaviour. Paris: UIC 518, 2009.

20.

Wang

, et al. Numerical analysis of the effect of track parameters on the wear of turnout rails in high-speed railways. Proc IMechE, Part F: J Rail and Rapid Transit 2018; 232(3): 709–721.

21.

Carlberger

Torstensson

Nielsen

JCO

, et al. An iterative methodology for the prediction of dynamic vehicle–track interaction and long-term periodic rail wear. Proc IMechE, Part F: J Rail and Rapid Transit 2018; 232(6): 1718–1730.

22.

Muhamedsalih

Stow

Bevan

. Use of railway wheel wear and damage prediction tools to improve maintenance efficiency through the use of economic tyre turning. Proc IMechE, Part F: J Rail and Rapid Transit 2019; 233(1): 103–117.

23.

Casanueva

Enblom

Stichel

, et al. On integrated wheel and track damage prediction using vehicle–track dynamic simulations. Proc IMechE, Part F: J Rail and Rapid Transit 2017; 231(7): 775–785.

24.

Jendel

Berg

. Prediction of wheel profile wear: Methodology and verification. Veh Syst Dyn 2002; 37(Suppl. 1): 502–513.