Many parts used in various industries are subjected to multiaxial stresses during service phase, and since cracks can be a source of failure in the parts, it is extremely important to analyze the strength of cracked structures under multiaxial loads, and improve the structures fracture strength. In the present research, the effect of clamping force resulted from bolted pre-tension and composite patches on enhancing fracture strength of edge cracked rectangular samples made of aluminum-alloy 2024-T3 are evaluated both experimentally and theoretically. The cracked laboratory samples were tested using a modified version of Arcan fixture to develop pure tensile, pure shear, and mixed modes of loading. Further, finite-element simulations were utilized to find stress intensity factors to explain the experimental test results. The experimental results indicate a significant increase in the tensile strength of repaired parts by the bolt clamping and composite patches compared to simple cracked samples. Repaired samples with composite patch and bolt clamping exhibited up to 44% and 24% increase in tensile strength under pure tensile mode, respectively. However, in pure shear mode, the fracture strength increased to 18% and 9% by bolt clamping and composite patch, respectively.
SongPSheuBChouH. Deposition of plating metals to improve crack growth life. Int J Fatigue2001; 23: 259–270.
2.
SchubbeJMallS. Investigation of a cracked thick aluminum panel repaired with a bonded composite patch. Eng Fract Mech1999; 63: 305–323.
3.
Linnert G. Welding metallurgy. Volume 2 – technology/(welding metallurgy, volume 2, technology, covering filler metals, shrinkage and distortion, defects, heating and weld tests). New York: American Welding Society, 1967.
4.
GotoMMiyagawaHNisitaniH. Crack growth arresting property of a hole and Brinell‐type dimple. Fatigue Fract Eng Mater Struct1996; 19: 39–49.
5.
ChakherlouTVogwellJ. The effect of cold expansion on improving the fatigue life of fastener holes. Eng Fail Anal2003; 10: 13–24.
6.
ChakherlouTMirzajanzadehMVogwellJ. Experimental and numerical investigations into the effect of an interference fit on the fatigue life of double shear lap joints. Eng Fail Anal2009; 16: 2066–2080.
7.
ChakherlouTRazaviMAghdamAet al.An experimental investigation of the bolt clamping force and friction effect on the fatigue behavior of aluminum alloy 2024-T3 double shear lap joint. Mater Des2011; 32: 4641–4649.
8.
AbazadehBChakherlouTAlderliestenRC. Effect of interference fitting and/or bolt clamping on the fatigue behavior of Al alloy 2024-T3 double shear lap joints in different cyclic load ranges. Int J Mech Sci2013; 72: 2–12.
9.
ChakherlouTAbazadehBVogwellJ. The effect of bolt clamping force on the fracture strength and the stress intensity factor of a plate containing a fastener hole with edge cracks. Eng Fail Anal2009; 16: 242–253.
10.
ChakherlouTRazaviMAghdamA. On the variation of clamping force in bolted double lap joints subjected to longitudinal loading: a numerical and experimental investigation. Strain2012; 48: 21–29.
11.
ChakherlouTOskoueiRVogwellJ. Experimental and numerical investigation of the effect of clamping force on the fatigue behaviour of bolted plates. Eng Fail Anal2008; 15: 563–574.
12.
ChakherlouTRazaviMAbazadehB. Finite element investigations of bolt clamping force and friction coefficient effect on the fatigue behavior of aluminum alloy 2024-T3 in double shear lap joint. Eng Fail Anal2013; 29: 62–74.
13.
YanYWenW-DChangF-Ket al.Experimental study on clamping effects on the tensile strength of composite plates with a bolt-filled hole. Compos Part A1999; 30: 1215–1229.
14.
SallamHEl-SisiAMatarEet al.Effect of clamping force and friction coefficient on stress intensity factor of cracked lapped joints. Eng Fail Anal2011; 18: 1550–1558.
15.
ChakherlouTMalekiHAghdamAet al.Effect of bolt clamping force on the fracture strength of mixed mode fracture in an edge crack with different sizes: experimental and numerical investigations. Mater Des2013; 45: 430–439.
16.
Baker A. Fatigue crack propagation studies on aluminium panels patched with boron/epoxy composites. In: International conference on aircraft damage assessment and repair: 1991; preprints of papers. Institution of Engineers, Australia, Melbourne 26-28 August 1991, p.209.
17.
ChungKHYangWH. Mixed mode fatigue crack growth in aluminum plates with composite patches. Int J Fatigue2003; 25: 325–333.
18.
AyatollahiMHashemiR. Computation of stress intensity factors (K I, K II) and T-stress for cracks reinforced by composite patching. Compos Struct2007; 78: 602–609.
19.
RamjiMSrilakshmiR. Design of composite patch reinforcement applied to mixed-mode cracked panel using finite element analysis. J Reinf Plast Compos2012; 31: 585–595.
20.
ArcanMHashinZAVoloshinA. A method to produce uniform plane-stress states with applications to fiber-reinforced materials. Exp Mech1978; 18: 141–146.
21.
ASTM D2651-90:1990. Standard guide for preparation of metal surfaces for adhesive bonding. ASTM standards.
22.
ASTM E8. Standard test methods for tension testing of metallic materials. In: Annual book of ASTM standards,American Society for Testing and Materials, Philadelphia, PA, 2001.
23.
ASTM D3039:2000. Standard test method for tensile properties of polymer matrix composite materials. ASTM standards.
24.
ASTM D638-02:2003. Standard test method for tensile properties of plastics. ASTM, West Conshohocken, PA.
25.
Swanson Analysis Systems Inc. ANSYS. User’s guide for revision 14, ANSYS 14 Documentation. Theory Reference, Element Library TARGET170 – 3D Target Segment. 2014.
26.
Swanson Analysis Systems Inc. ANSYS. User’s guide for revision 14, ANSYS 14 Documentation, Theory Reference, Element Library. CONTA174 – 3D surface-to-surface contact. 2014.
27.
ASTM E399:1983. Standard test method for plane strain fracture toughness and strain energy release rate of metallic materials. American Society for Testing and Materials, Philadelphia, PA.
28.
ASTM D5045:1995. Standard test methods for plane-strain fracture toughness and strain energy release rate of plastic materials. American Society for Testing and Materials, Philadelphia, PA.
29.
ChoupaniN. Experimental and numerical investigation of the mixed-mode delamination in Arcan laminated specimens. Mater Sci Eng A2008; 478: 229–242.
30.
NouryPShenoiRSinclairI. On mixed-mode fracture of PVC foam. Int J Fract1998; 92: 131–151.
YoonSHongC. Interlaminar fracture toughness of graphite/epoxy composite under mixed-mode deformations. Exp Mech1990; 30: 234–239.
33.
Banks-SillsLArcanMBortmanY. A mixed mode fracture specimen for mode II dominant deformation. Eng Fract Mech1984; 20: 145–157.
34.
GdoutosE. Engineering application of fracture mechanics, VII, problems of mixed mode crack propagation, Boston, MA: Martinus Nijhoff Pub, 1984.
35.
ChakherlouTMalekiHAbazadehBet al.Investigating bolt clamping force effect on the mixed mode fracture strength and stress intensity factor for an edge crack in PMMA specimens. Mater Sci Eng A2012; 533: 71–81.
36.
ChakherlouTHakimSMohammadpourAet al.Experimental and numerical investigations of crack face adhesive bonding effect on the mixed-mode fracture strength of PMMA. J Adhes Sci Technol2016; 30: 2236–2256.
37.
Maleki HN and Chakherlou TN Investigation of the effect of bonded composite patch on the mixed-mode fracture strength and stress intensity factors for an edge crack in aluminum alloy 2024-T3 plates. Journal of Reinforced Plastics and Composites. 2017; 36: 1074–91.
