Optimization of lightweight sub-stiffened panels with buckling analysis and imperfection sensitivity analysis

Abstract

On the purpose of improving the structural efficiency of stiffened panels, which is widely used in engineering, three promising layouts of sub-stiffened thin-walled structures were optimized in view of structure's initial buckling and further analyzed through post-buckling and imperfection-sensitivity analysis. The optimization tasks were carried out using an integrated framework, which is based on the multidisciplinary optimization platform Model Center and finite element method software ABAQUS. The particle swarm optimization algorithm was applied to optimize layout parameters. Three optimal sub-stiffened panels were then evaluated based on their performance on critical buckling loads and post-buckling ultimate strength under uniaxial loading. Imperfection-sensitivity analysis was also conducted to investigate the stability behavior of the proposed panels with defect. The results indicate that the introduction of sub-stiffeners into the traditional stiffened panel can achieve significant improvements on the panel's buckling loads and ultimate strength under uniaxial loading, which are favorable to expand design space for engineering structures under requirements of lightweight with high bending stiffness and bucking resistance.

Keywords

Sub-stiffened buckling optimization framework finite element analysis particle swarm optimization

Get full access to this article

View all access options for this article.

References

Cerini M and Falzon BG. The reliability of the arc-length method in the analysis of mode-jumping problems. In: Proceedings of 44th AIAA/ASME/ASCE/AHS structures, structural dynamics, and materials conference, Norfolk, VA, USA, 7–10 April 2003, pp.2003–1621. Reston, VA: AIAA.

Bushnell D and Rankin C. Optimum design of stiffened panels with sub-stiffeners. In: Proceedings of 46th AIAA/ASME/ASCE/AHS/ASC structures, structural dynamics, and materials conference, 2005, pp.1–54. Reston, VA: AIAA.

Özakça M, Murphy A and van der Veen S. Buckling and post-buckling of sub-stiffened or locally tailored aluminum panels. In: Proceedings of 25th international congress of the aeronautical sciences, Bonn, Germany, 1 September 2006.

Quinn

Murphy

McEwan

, et al. Stiffened panel stability behavior and performance gains with plate prismatic sub-stiffening. Thin-Walled Struct 2009; 47: 1457–1468.

Murphy A, Quinn D, Mawhinney P, et al. Tailoring static strength performance of metallic stiffened panels by selective local sub-stiffening. In: Proceedings of 47th AIAA/ASME/ASCE/AHS/ASC structures, structural dynamics, and materials conference, New Port RI, USA, 1–4 May 2006. Reston, VA: AIAA.

Quinn

Murphy

McEwan

, et al. Non-prismatic sub-stiffening for stiffened panel plates—stability behavior and performance gains. Thin-Walled Struct 2010; 48: 401–413.

Tamijani

McQuigg

Kapania

. Free vibration analysis of curvilinear-stiffened plates and experimental validation. J Aircraft 2010; 47: 192–200.

Joshi P, Mulani SB, Slemp WCH, et al. Minimization of acoustic radiation from a turbulent boundary layer excited panel with curvilinear stiffeners. In: Proceedings of 55th AIAA/ASME/ASCE/AHS/SC structures, structural dynamics, and materials conference, Orlando, Florida, USA, 12–15 April 2010. Reston, VA: AIAA.

Kapania RK, Li J and Kapoor H. Optimal design of unitized panels with curvilinear stiffeners. In: Proceedings of AIAA 5th ATIO and the AIAA 16th lighter-than-air systems technology conference and balloon systems conference, 2005, pp.1708–1737. Arlington, VA: AIAA.

10.

Mehnen

Ding

Lockett

, et al. Design study for wire and arc additive manufacture. Int J Product Dev 2014; 19: 2–20.

11.

Kapania RK, Mulani SB, Tamijani A, et al. EBF3PanelOpt: a computational design environment for panels fabricated by additive manufacturing. In: Proceedings of 51st AIAA aerospace sciences meeting including the new horizons forum and aerospace exposition, Texas, USA, 2013.

12.

Slemp

WCH

Keith Bird

Kapania

, et al. Design, optimization and evaluation of integrally stiffened Al 7050 panel with curved stiffeners. J Aircraft 2011; 48: 1163–1175.

13.

Mulani

Havens

Norris

, et al. Design, optimization, and evaluation of Al-2139 compression panel with integral T-stiffeners. J Aircraft 2013; 50: 1275–1286.

14.

Wang

. Design and optimization of improving stability of curvilinear blade-stiffened panels. J Beijing Univ Aeronaut Astronaut 2015; 41: 567–573.

15.

Zhang

Yao

Liu

. Configuration optimization method for metallic stiffened panel structure based on updated Kriging model. J Nanjing Univ Aeronaut Astronaut 2008; 40: 497–500.

16.

Dang

Kapania

Slemp

WCH

, et al. Optimization and post buckling analysis of curvilinear-stiffened panels under multiple-load cases. J Aircraft 2010; 47: 1656–1671.

17.

Watson A, Featherston CA and Kennedy D. Optimization of post buckled stiffened panels with multiple stiffener sizes. In: Proceedings of 48th AIAA/ASME/ASCE/AHS/ASC structures, structural dynamics, and materials conference, Honolulu, HI, USA, 23–26 April 2007, pp.5942–5949. Reston, VA: AIAA.

18.

Cerini

Falzon

. Use of the arc-length method for capturing mode jumping in post-buckling aero structures. AIAA J 2005; 43: 681–689.

19.

Hühne

Rolfes

Breitbach

, et al. Robust design of composite cylindrical shells under axial compression — simulation and validation. Thin-Walled Struct 2008; 46: 947–962.

20.

Wang

Tian

Hao

, et al. Load-carrying capacity and imperfection-sensitivity analysis of hierarchical stiffened panels. J Solid Rocket Technol 2015; 3: 408–412.