Efficiency enhancement mechanisms of a new type of full reversible axial-flow fan

Abstract

A row of airfoil-shaped support struts has been proposed to be installed on both sides of the rotor, so as to remedy the configuration asymmetry of a conventional fully reversible fan in its forward and reverse flow modes. In the forward mode, the upstream support struts act as inlet guide vanes (GVs), and the downstream ones as outlet GVs; whereas in the reverse mode, the roles played by the two support-strut rows switch over. Among the five representative airfoils, symmetric airfoil NACA0012-64 is found to be the most suitable airfoil used as the section of the two rows of the airfoil-shaped support struts. Detailed numerical investigations on four such new fans, whose design points cover a wide range, reveal that the installation of the two rows of blades improves the performance of the new type fan, when compared with the one-rotor fully reversible axial-flow fan without such support-struts. The upstream blade row has little influence on the direction of incoming flow and causes little aerodynamic losses. By contrast, the downstream blade row plays an important role in efficiency improvements: (1) the downstream blade row, which acts as outlet GVs, significantly reduces the rotor-exit tangential velocity and recovers part of the swirl energy in the flow downstream of the rotor, although sometimes the aerodynamic losses caused by such support-strut-like outlet GVs may be high at a large incidence; (2) due to the obviously reduced tangential components of the flow velocities downstream of the outlet GV, the air travels a much shorter distance toward the exit of the annular diffuser, compared with that in the fan without outlet GVs. This leads to a markedly reduced friction loss. In addition, the larger the equivalent divergence angle of the annular diffuser is, the more effectively does the installation of the two rows of the support-strut-like blade improve the performance of the new type fans.

Keywords

fully reversible axial-flow fan guide vanes efficiency improvement tunnels and subways

Get full access to this article

View all access options for this article.

References

Carvel

R. O.

Beard

A. N.

Jowitt

P. W.

The influence of longitudinal ventilation systems on fires in tunnels. Tunnelling and Underground Space Technol., 2001, 16, 3–21.

Gabay

Fire safety: a short history in the Paris Subway. (2002 ITA open session: fire and life safety). Tunnelling and Underground Space Technol., 2002, 17, 139–143.

Stefopoulos

E. K.

Damigos

D. G.

Design of emergency ventilation system for an underground storage facility. Tunnelling and Underground Space Technol., 2007, 22, 293–302.

Yuan

F. D.

You Sh-

CFD simulation and optimization of the ventilation for subway side-platform. Tunnelling and Underground Space Technol., 2007, 22, 474–482.

Cheng

L. H.

Ueng

T. H.

Liu

C. W.

Simulation of ventilation and fire in the underground facilities. Fire Saf. J., 2001, 36, 597–619.

Vega

M. G.

Diaz

K. M. A.

Oro

J. M. F.

Tajadura

R. B.

Morros

C. S.

Numerical 3D simulation of a longitudinal ventilation system: memorial tunnel case. Tunnelling and Underground Space Technol., 2008, 23, 539–551.

Petrov

N. N.

Popov

N. A.

Batyayev

Ye. A.

Novikov

V. A.

Theory and design of reversible axial fans with turn in motion blades of impeller. J. Min. Sci., 1999, 35, 519–530.

Radha Krishna, H. J., Aswathanarayana, P. A., and Ramachandran, Rm. Some flow studies on S-cambered aerofoils. In Proceeding of the 6th Conference on Fluid machinery, Budapest, Hungry, 1979, pp. 917–925.

Ravindran, M. and Radha Krishna, H. J. Influence of blade profiles on the performance of fully reversible axial pump-turbine. In Proceeding of the 6th Conference on Fluid machinery, Budapest, Hungry, 1979, pp. 926–935.

10.

Ravindran, M. and Radha Krishna, H. J. Characteristics of a fully reversible axial pump-turbine for application in tidal power plants. In Proceedings of the International Conference on Future energy concepts, London, 1979, pp. 156–158.

11.

Chacko

Balabaskaran

Tulapurkara

E. G.

Radha Krishna

H. C.

Performance of s-cambered profiles with cut-off trailing edges. Trans. ASME, J. Fluids Eng., 1994, 116, 522–527.

12.

C. J.

Zhao

D. W.

Wei

B. S.

The optimal design and experimental study of double-direction axial flow fan. Chinese J. Mech. Eng., 1991, 27(5), 54–60.

13.

Fernández Oro

J. M.

Argüelles Díaz

K. M.

Santolaria Morros

Ballesteros-Tajadura

Impact of the tip vortex on the passage flow structures of a jet fan with symmetric blades. Proc. IMechE, Part A: J. Power and Energy, 2009, 223, 141–155.

14.

Tan

Chen

Liang

Three-dimensional design of hundred-percent reversible subway fans. Chinese J. Mech. Eng., 2006, 42(9), 169–173.

15.

Wallis

R. A.

Axial flow fans and ducts, 1983 (John Wiley, New York).

16.

Chao, C-C. and Chen, H-P. Evaluation of turbulence models for the CPU cooling fan. In ASSRC/CCAS Joint conference, paper no. 02_04, Jhongli city, Taiwan, 2006.

17.

Kang

Guo

Tang

B. H.

Numerical simulation of a small-scale axial CPU fan. J. Eng. Thermophys., 2009, 30, 1853–1855.

18.

International Organization for Standardization. Industrial fans – performance testing using standardized airways, Geneva, Switzerland , 1997 (ISO5801.

19.

C. J.

Wei

B. S.

A study on a new type airfoil-‘S’ shaped airfoil with double circles used in reversible axial fans. Chinese J. Mech. Eng., 1992, 28(4), 37–41.

20.

Timmer, W. A. and van Rooij, R. Some aspects of high angle-of-attack flow on airfoils for wind turbine application. In European wind energy conference, Copenhagen, Denmark, 2–6 July 2001.