Numerical investigations on the leakage flow characteristics of pocket damper labyrinth seals

Abstract

A combined finite element analysis and computational fluid dynamics was developed to investigate the discharge characteristics and flow field of pocket damper seals at high pressure (up to 7.2 MPa) and high rotational speed (up to 50,200 r/min) flow condition. At first, the leakage flow rates of the published experimental pocket damper seals with the eight-bladed and eight-pocket were conducted at three different pressure drops and three different rotational speeds, and a comparison between finite element analysis and computational fluid dynamics results, experimental data and computational fluid dynamics results was presented. It showed that the utilized finite element analysis/computational fluid dynamics numerical method has sufficient precision (the maximum relative deviation is less than 1.3%) to predict the leakage flow rate through the pocket damper seals. The importance of taking rotor growth with rotational speed into consideration was made apparent by the rotor growth and leakage results. Then, six pressure ratios and seven rotational speeds were utilized to study the effects of these two factors on the leakage flow characteristics of the pocket damper seals. Numerical simulation results show that the leakage through a pocket damper seals increases with decreasing pressure ratio and asymptotically approach a maximum value corresponding to the choked flow condition when the pressure ratio is small enough (less than 0.26). The leakage flow rate with and without rotor growth included both decrease with the increasing rotational speed. In addition, it is quite necessary to take rotor growth with rotational speed into consideration when the rotational speed is very high (larger than 20,200 r/min) according to the numerical results and the engineering accuracy requirement. The influence of the pressure ratio on the structure of the leakage flow field in seal cavity is negligible. A significant influence of the rotational speed on the flow field in the active cavity has been observed. The circumferential partition wall can significantly decrease the circumferential flow in active cavity of the pocket damper seals.

Keywords

Pocket damper seal leakage flow characteristics finite element analysis/computational fluid dynamics numerical simulation

Get full access to this article

View all access options for this article.

References

Lakshminarayana

. Fluid dynamics and heat transfer of turbomachinery. New York: Wiley, 1996, pp. 339–347.

Thomas

. Instabile Eigenschwingungen von Turbinenlaufern angefacht durch die Spaltstromungen Stopfbuschen und Beschauflungen. Bull deL’AIM 1958; 71: 1039–1063.

Lattime

Steinetz

. Turbine engine clearance control systems: current practices and future directions. J Propul Power 2004; 120(2): 302–311.

Chupp

Ghasripoor

Turnquist

. Advanced seals for industrial turbine applications: dynamic seal development. J Propul Power 2002; 18(6): 1260–1266.

Chupp

Hendricks

Lattime

. Sealing in turbomachinery. J Propul Power 2006; 22(2): 313–349.

Vance

. Machinery vibration and rotordynamics. New York: John Wiley and Sons, 2010, pp. 271–272.

Childs D and Vance J. Annular seals as tools to control rotordynamic response of future gas turbine engines. AIAA Paper 94-2804, 1994.

Childs

Wade

. Rotordynamic-coefficient and leakage characteristics for hole-pattern-stator annular gas seals-measurements versus predictions. ASME J Tribol 2004; 126(2): 326–333.

Vance J and Schultz R. A new damper seal for turbomachinery. Vibration of rotating systems, ASME DE, 60, September 1993.

10.

Richards RL, Vance JM and Zeidan FY. Using a damper seal to eliminate subsynchronous vibrations in three back-to-back compressors. In: Proceedings of 24th turbomachinery symposium, Turbomachinery Laboratory, Texas A&M University, College Station, Texas, 1995, pp.370–376.

11.

Vance

. Test results of a new damper seal for vibration reduction in turbomachinery. ASME J Eng Gas Turb Power 1996; 118: 843–846.

12.

Li J and Vance JM. Effects of clearance and clearance ratio on two and three bladed TAMSEALS, TRC-Seal-4-95. Turbomachinery Laboratory Research Progress Report, Texas A&M University, College Station.

13.

Ransom

San Andrés

. Experimental force coefficients for a two-bladed labyrinth seal and a four pocket damper seal. ASME J Tribol 1998; 28: 98–109.

14.

Laos HE. Rotordynamic effect of pocket damper seals. PhD Dissertation, Texas A&M University, College Station, USA, 1999.

15.

Ertas B. Rotordynamic force coefficients of pocket damper seals. PhD Dissertation, Texas A&M University, USA, 2005.

16.

Childs DW and Vance JM. Annular gas seals and rotordynamics of compressors and turbines. In: Proceedings of 26th turbomachinery symposium, Texas A&M University, College Station, TX, pp.201-220.

17.

Gamal

. Analytical and experimental evaluation of the leakage and stiffness characteristics of high pressure pocket damper seals. MS Thesis, Mechanical Engineering Department: Texas A&M University, USA, 2003.

18.

Gamal AM. Leakage and rotordynamic effects of pocket damper seals and see-through labyrinth seals. PhD Dissertation, Mechanical Engineering Department, Texas A&M University, College Station, USA, 2007.

19.

Waschka

Wittig

Kim

. Influence of high rotational speeds on the heat transfer and discharge coefficients in labyrinth seals. ASME J Turbomach 1992; 114(2): 462–468.

20.

Gamal

Ertas

Vance

. High-pressure pocket damper seals: leakage rates and cavity pressures. ASME J Turbomach 2007; 129: 826–834.

21.

Gamal

Vance

. Labyrinth seal leakage tests: tooth profile, tooth thickness, and eccentricity effects. ASME J Eng Gas Turb Power 130: 012510–012510.

22.

Schramm

Willenborg

Kim

. Influence of a honeycomb facing on the flow through a stepped labyrinth seal. ASME J Eng Gas Turb Power 2002; 124: 140–146.

23.

Yan

Song

. Investigations on the discharge and total temperature increase characteristics of the labyrinth seals with honeycomb and smooth lands. ASME J Turbomach 2008; 131(4): 041009–041009.

24.

Shengru

Yan

. Numerical investigations on leakage performance of the rotating labyrinth honeycomb seal. ASME J Eng Gas Turb Power 2010; 132: 062501–062501.

25.

Li Z, Li J, Feng Z, et al. Numerical investigations on the leakage flow characteristics of pocket damper seals. ASME Paper GT2011-45114, 2011.

26.

ANSYS. ANSYS User Document, Version 11.0, 2007.

27.

AEA Technology GmbH. CFX-TASCflow User Documentation, AEA Technology, Software Ltd., Waterloo, ON, Canada, 2004.

28.

Young

. Roark’s formulas for stress and strain, 6th ed. New York: McGraw Hill, 1989.

29.

Ahmed

Gamal

John

. Labyrinth seal leakage tests: tooth profile, tooth thickness, and eccentricity effects. J ASME J Eng Gas Turb Power 2008; 130: 012510–012510.