Prediction of impeller rotating stall onset using numerical simulations of a centrifugal compressor. Part 1: Detection of rotating stall using fixed-flow transient simulations
Restricted accessResearch articleFirst published online June, 2013
Prediction of impeller rotating stall onset using numerical simulations of a centrifugal compressor. Part 1: Detection of rotating stall using fixed-flow transient simulations
Rotating stall is an unsteady flow phenomenon that appears in both axial and centrifugal compressors. It is detrimental to the performance of the compressor, significantly narrowing its operating range. Numerical modeling of this phenomenon has been a major area of investigation for axial compressors with some success. While stall occurs less often in centrifugal compressors than axial ones, it can be much harder to predict. Some preventive measures are known but are mostly rules of thumb developed through experimental experience. This work focuses on the detection of impeller rotating stall using computational fluid dynamics. A compressor was chosen that has demonstrated rotating stall instabilities with different diffuser lengths and return vanes. Unsteady numerical simulations were performed on full 360° models of this geometry. The transient simulations were conducted using distributed processing on high-performance servers. The objective was to determine the accuracy in which rotating stall can be captured in simulations. For this purpose, simulation results were compared to experimental results for the same compressor and show a good correlation between the experimental and numerical tests.
Whitbeck NG. An experimental study of blade-to-blade pressure differences and operating characteristics of a centrifugal compressor. Master's Thesis, Michigan State University, USA, 1994.
3.
JansenW. Rotating stall in a radial vaneless diffuser. ASME J Basic Eng1964; 86: 750–758. ASME paper 64-FE-6.
4.
FrignePVan den BraembusscheR. Distinction between different types of impeller and diffuser rotating stall in a centrifugal compressor with vaneless diffuser. ASME J Eng Gas Turbines Power1984; 106: 468–474.
5.
Abdelhamid AN. Analysis of rotating stall in vaneless diffusers of centrifugal compressors. In: ASME gas turbine conference and products show, New Orleans, USA, March 1980, ASME paper 80-GT-184.
6.
KämmerNRautenbergM. A distinction between different types of stall in centrifugal compressor stage. ASME J Eng Gas Turbines Power1986; 108: 83–93. ASME paper 85-GT-194.
7.
AbdelhamidAN. Effects of vaneless diffuser geometry on flow instability in centrifugal compression systems. CASJ1983; 29: 259–266.
8.
Mizuki S, Kawashima Y and Ariga I. Investigation concerning rotating stall and surge phenomena within centrifugal compressor channels. In: ASME international gas turbine conference, London, UK, 1978, ASME paper 78-GT-9.
9.
Kämmer N and Rautenberg M. An experimental investigation of rotating stall flow in a centrifugal compressor. In: ASME international gas turbine conference and exhibit, London, UK, April 1982, ASME paper 82-GT-82.
10.
LennemannEHowardJ. Unsteady flow phenomena in rotating centrifugal impeller passages. ASME J Eng Power1970; 92: 65–72.
11.
KrauseNZähringerKPapE. Time-resolved particle image velocimetry for the investigation of rotating stall in a radial pump. Exp Fluids2005; 39: 192–201.
Stein A. Computational analysis of stall and separation control in centrifugal compressors. PhD Dissertation, Georgia Institute of Technology, USA, May 2000.
14.
Iwakiri K, Furukawa M, Ibaraki S and Tomita I. Unsteady and three-dimensional flow phenomena in a transonic centrifugal compressor impeller at rotating stall. In: ASME turbo expo 2009, Orlando, USA, June 2009, ASME paper GT2009-59516.
15.
David T, Zhang D and Cave M. Frictional effects on a base and a flow-trimmed impeller of a low specific speed industrial compressor. In: ASME turbo expo 2006 2006; 6B: 1121–1130, Barcelona, Spain, ASME paper GT2006-90998.
16.
Ji M, Cave M and Zhang D. Effects of impeller blade loading on industrial centrifugal compressor performance and stability. In: ASME international mechanical engineering congress & exposition, Vancouver, Canada, November 2010, ASME paper IMECE2010-40929.
17.
Abdelhamid AN, Haupt U and Rautenberg M. Unsteady flow characteristics in a centrifugal compressor with vaned diffuser. In: ASME gas turbine conference and exhibition, Anaheim, CA, USA, May 1987, ASME paper 87-GT-142.
18.
OhWHYoonESChungMK. An optimum set of loss models for performance prediction of centrifugal compressors. Proc IMechE, Part A: J Power Energy1997; 221(4): 331–338.
19.
Using the solver in parallel. In: ANSYS CFX-solver modeling guide. Canonsburg, PA: ANSYS, Inc., November 2009, ch. 14, pp.347–364.
20.
Pope SB. Turbulent-viscosity models. In: Turbulent flows. Cambridge: Cambridge University Press, 2009, ch. 10, pp.358–386.
21.
Anderson JD. Computational fluid dynamics: The basics with applications, International ed. Singapore: McGraw-Hill, 1995.
22.
Anish S and Sitaram N. Steady and transient computations of interaction effects in a centrifugal compressor with different types of diffuser. In: ASME turbo expo 2010, Glasgow, UK, June 2010, ASME paper GT2010-22913.
23.
ChenJPWebsterRSHathawayMDHerrickGPSkochGJ. High performance computing of compressor rotating stall and control. ICAE2009; 16: 73–89.
24.
HoyingDATanCSVoHDGreitzerEM. Role of blade passage flow structures in axial compressor rotating stall inception. ASME J Turbomach1999; 121: 735–742.
25.
MärzJHahCNeiseW. An experimental and numerical investigation into the mechanisms of rotating instability. ASME J Turbomach2002; 124: 367–375.
26.
LegrasGGourdainNTrebinjacI. Numerical analysis of the tip leakage flow field in a transonic axial compressor with circumferential casing treatment. J Thermal Sci2010; 19: 198–205.
27.
Choi M, Smith NHS and Vahdati M. Validation of numerical simulation for rotating stall in a transonic fan. In ASME turbo expo 2011, Vancouver, Canada, 2011, ASME paper GT2011-46109.
28.
SanoTYoshidaYTsujimotoY. Numerical study of rotating stall in a pump vaned diffuser. ASME J Fluids Eng2002; 124(2): 363–370.
29.
LuciusABrennerG. Numerical simulation and evaluation of velocity fluctuations during rotating stall of a centrifugal pump. ASME J Fluids Eng2011; 133: 081102–081102.
30.
Ljevar S, de Lange HC and van Steenhoven AA. Two-dimensional rotating stall analysis in a wide vaneless diffuser. Int J Rotating Mach 2006; 1–11; Article ID 56420.
31.
Everitt JN and Spakovszky ZS. An investigation of stall inception in centrifugal compressor vaned diffusers. In: ASME turbo expo 2011, Vancouver, Canada, 2011, ASME paper GT2011-46332.
