Through-flow calculation with a cooling model for cooled turbines

Abstract

Conjugate heat transfer is a key feature of modern gas turbine, as cooling technology is widely applied to improve the turbine inlet temperature for high efficiency. Impact of conjugate heat transfer on heat loads and thermodynamic efficiency is a key issue in gas turbine design. This paper proposes a through-flow method for the design of cooled turbines, taking into account the influence of the complicated interaction between the flow field and heat transfer in cooled turbines. The energy and continuity equations are rederived theoretically by considering the historical influence of cooling with the method that deals with viscous losses. A cooling model is introduced to the through-flow method to predict the coolant requirement. This paper applies the method in the design of a high-pressure turbine with convective cooling. With the prescribed blade temperature limitation and the knowledge of the flow variables of the mainstream at the turbine inlet, such as the total pressure, total temperature, and mass flow rate, the convergence of the calculation is then obtained and the properties of the flow field, velocity triangles, and coolant requirement are well predicted. Three-dimensional conjugate heat transfer analysis is performed for the validation of the through-flow method. By comparing these two calculations, it is shown that the through-flow method is a useful tool for flow analysis and coolant requirement prediction in the design of cooled turbines.

Keywords

Through-flow method cooling model cooled turbines

Get full access to this article

View all access options for this article.

References

Wu CH. A general theory of three-dimensional flow in subsonic and supersonic turbomachines of axial-, radial- and mixed-flow types. NACA TN 2604, 1952.

Herzog J. Calculation of flow distribution in large radius ratio stages of axial flow turbines and comparison of theory and experiment. NASA-SP-304, 1974.

Novak

. Steamline curvature computing procedures. ASME J Eng Power 1967; 89: 478–490.

Denton

. Through-flow calculations for transonic axial flow turbines. J Eng Power 1978; 100: 212–218.

Mildner

Gallus

. An analysis method for multistage transonic turbines with coolant mass flow addition. ASME J Turbomach 1998; 120: 744–752.

Gehring S and Riess W. Analysis of the mixing process in a 1.5 stage turbine with coolant ejection. ASME Paper No. 2000-GT-669, 2000.

Petrovic

Wiedermann

. Through-flow analysis of air-cooled gas turbines. J Turbomach 2013; 135: 061019–061019.

Holland

Thake

. Rotor blade cooling in high pressure turbines. J Aircraft 1980; 17: 412–418.

Ainley DG. Internal air cooling for turbine blades: a general design study. Aeronautical Research Council Reports and Memorandum 3013, 1957.

10.

Consonni S. Performance prediction of gas/steam cycles for power generation. PhD Thesis No. 1983-T, MAE Dept. Princeton Univ, 1992.

11.

Torbidoni

Horlock

. A new method to calculate the coolant requirements of a high temperature gas turbine blade. ASME J Turbomach 2005; 127: 191–199.

12.

Ainley DG and Mathieson GCR. A method of performance estimation for axial-flow turbine, ARC, R&M 2974, 1957.

13.

Dunham J and Came PM. Improvements to the Ainley-Mathieson method of turbine performance prediction. J Eng Power 1970; 92: 252–256.

14.

Kacker

Okapuu

. A mean line prediction method for axial flow turbine efficiency. ASME J Eng Power 1982; 112: 111–119.

15.

Holman

. Heat transfer, 6th ed. New York: McGraw-Hill, 1986, pp. 254–254.

16.

El-Masri MA and Pourkey F. Prediction of cooling flow requirements for advanced utility gas turbines. Part 1: analysis and scaling of the effectiveness curve. ASME paper 86-WA/HT-43, 1986.

17.

Hartsel JE. Prediction of effects of mass-transfer cooling on the blade-row efficiency of turbine airfoils. In: AIAA, 10th Aerospace Sciences Meeting, Reston, VA, USA: Aerospace Research Central, 1972, pp.8–19.

18.

Shapiro

. The dynamics and thermodynamics of compressible fluid flow 1953; volume I, New York: Ronald Press, pp. 219–231.

19.

Shrivastava KD and Maccallum NRL. The effect of a transversely injected stream on the flow through turbine cascades—part II: performance changes. ASME paper no. 87-GT-88, 1987.

20.

Day

CRB

Oldfield

MLG

Lock

. Aerodynamic performance of an annular cascade of film cooled nozzle guide vanes under engine representative conditions. Exp Fluids 2000; 29: 117–129.

21.

Zeng J. Experimental and numerical investigation of the turbine cascade with film cooling jets. PhD Thesis, Nanjing University of Aeronautics and Astronautics, Nangjing, 2007.