Effect of blade tip grooving on the performance of an axial fan at different tip clearances in the absence and presence of inlet guide vanes

Abstract

This research aims at the numerical study of the blade tip grooving effect on the performance of a ducted axial fan at different tip clearances in the absence and presence of inlet guide vanes. To do this, significant parameters of the fan (i.e. pressure and torque coefficients as well as fan efficiency) comprising single- and double-grooved tips are evaluated and compared with those of the original fan. Validation of the considered numerical model is performed through comparison of the numerical findings with experimental results of a single-stage ducted fan, which comprises a set of 37 guide vane and 24-blade rotor rotating at the speed of 3600 r/min. Results reveal that grooving the blade tip causes the fan parameters to increase and higher fan parameters could be attained adopting single-grooved tip. It is shown that employing grooved blades causes the sensitivity of fan parameters to the change in the tip clearance to diminish. Results exhibit that the impact of grooving the blade on the reduction of sensitivity of fan parameters to the change in the tip clearance for the single-grooved tip in the absence of guide vanes is more remarkable than the other cases and in this case, as the tip clearance increases from the lower to the upper considered value, the decreased percentages in pressure coefficient, torque coefficient, and fan efficiency are 29.8%, 8.9%, and 22.8%, respectively. Numerical findings show that the influence of grooving the blade on the fan parameters in the presence of guide vanes is lower than that without guide vanes and in the presence of guide vanes, the highest average increase percentages in pressure coefficient, torque coefficient, and fan efficiency relative to those of the original fan, which is observed in the single grooved tip, are 3.1%, 1.4%, and 1.7%, respectively.

Keywords

Blade tip groove tip clearance pressure coefficient torque coefficient fan efficiency

Get full access to this article

View all access options for this article.

References

Kesharwani S and Mistry CS. Design aspects for large diameter, low speed axial flow fan for wind tunnel application. In: Proceedings of the ASME 2017 gas turbine India conference GTINDIA2017, Bangalore, India, 7–8 December 2017.

Ingistov S. Efforts to improve aerodynamics of the large cooling tower fan by modifications of the fan stack. In: ASME turbo expo 2008: power for land, sea, and air, Berlin, Germany, 9–13 June 2008.

Akturk A and Camci C. Tip clearance investigation of a ducted fan used in VTOL UAVS, part 1: baseline experiments and computational validation. In: Proceedings of ASME turbo expo turbine technical conference, Vancouver, Canada, 6–10 June 2011.

, et al. Numerical investigation of blade tip grooving effect on performance and dynamics of an axial flow fan. Energy 2015; 82: 556–569.

Zhu X, Du Z and Zhao Y. Experimental investigation of tip clearance flows of an axial flow fan using PDA. In: ASME 2002 joint U.S.-European fluids engineering division conference volume 2: symposia and general papers, Parts A and B, Montreal, QC, Canada, 14–18 July 2002.

Jang

C-M

Sato

Fukano

. Experimental analysis on tip leakage and wake flow in an axial flow fan according to flow rates. ASME J Fluids Eng 2004; 127: 322–329.

Zhu

Lin

. Experimental and numerical investigation of the flow field in the tip region of an axial ventilation fan. ASME J Fluids Eng 2004; 127: 299–307.

Zhu X, Lin W and Du Z. Experimental investigation of the tip clearance flow for an axial flow fan rotor using a PIV system. In: ASME 2004 heat transfer/fluids engineering summer conference volume 2, Parts A and B, Charlotte, NC, USA, 11–15 July 2004.

Corsini A, Perugini B, Rispoli F, et al. Investigation on improved blade tip concept for axial flow fan. In: ASME turbo expo 2006: power for land, sea, and air volume 6: turbomachinery, Parts A and B, Barcelona, Spain, 8–11 May 2006.

10.

Liu

Hou

, et al. Measurement and analysis of tip clearance unsteady flow spectrum in axial-flow fan rotor. Front Energy Power Eng China 2008; 2: 448–452.

11.

Aktürk

Camci

. Axial flow fan tip leakage flow control using tip platform extensions. ASME J Fluids Eng 2010; 132: 051109–051109.

12.

Pogorelov A, Meinke MH, Schroeder W, et al. Cut-cell method based large-eddy simulation of a tip-leakage vortex of an axial fan. In: 53rd AIAA aerospace sciences meeting, 2015. Reston, VA: AIAA.

13.

Pogorelov

Meinke

Schroder

. Effects of tip-gap width on the flow field in an axial fan. Int J Heat Fluid Flow 2016; 61: 466–481.

14.

Chen

Koley

, et al. An experimental study of stall suppression and associated changes to the flow structures in the tip region of an axial low speed fan rotor by axial casing grooves. ASME J Turbomach 2017; 139: 121010–121010.

15.

Gamil AAA, Teixeira JA and Addali A. Demonstration of leakage flow distribution of an axial fan inside the tip clearance gap. In: 55th AIAA aerospace sciences meeting, Grapevine, TX, USA, 9–13 January 2017.

16.

Nho

Park

Yong

, et al. Effects of turbine blade tip shape on total pressure loss and secondary flow of a linear turbine cascade. Int J Heat Fluid Flow 2012; 33: 92–100.

17.

De Maesschalck

Lavagnoli

Paniagua

. Blade tip carving effects on the aerothermal performance of a transonic turbine. ASME J Turbomach 2015; 137: 021005–021005.

18.

Yan

Huang

, et al. Numerical investigations into the effect of squealere winglet blade tip modifications on aerodynamic and heat transfer performance. Int J Heat Mass Transfer 2016; 103: 242–253.

19.

Jung

Choi

Park

, et al. Effects of recessed blade tips on the performance and flow field in a centrifugal compressor. Proc IMechE, Part A: J Power and Energy 2012; 227: 157–166.

20.

Han

Zhong

. Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor. Chinese J Aeronaut 2016; 29: 653–661.

21.

Jung

Jeon

Jung

, et al. Effects of recessed blade tips on stall margin in a transonic axial compressor. Aerosp Sci Technol 2016; 54: 41–48.

22.

, et al. Numerical investigation of blade tip grooving effect on performance and dynamics of an axial flow fan. Energy 2015; 82: 556–569.

23.

Zhang

. Effect of blade tip pattern on performance of a twin-stage variable pitch axial fan. Energy 2017; 126: 535–563.

24.

Bell EB. Test of a single-stage axial-flow fan. Langley Memorial Aeronautical Laboratory, Report No. 729, 1942.

25.

Ki-Sang

Kwang-Yong

Abdus

. Design optimization of low-speed axial flow fan blade with three-dimensional RANS analysis. J Mech Sci Technol 2008; 22: 1864–1869.

26.

Kim

J-H

Kim

J-W

Kim

K-Y

. Axial-flow ventilation fan design through multi-objective optimization to enhance aerodynamic performance. ASME J Fluids Eng 2011; 133: 101101–101101.

27.

Venter

Kroger

. The effect of tip clearance on the performance of an axial flow fan. Energy Convers Manage 1992; 33: 89–97.

28.

Rains DA. Tip clearance flows in axial flow compressors and pumps. PhD Dissertation, California Institute of Technology, USA, 1954.