In order to investigate the effect of impeller tip clearance on internal flow fields and the rotating stall inception impacted by tip leakage vortex and inlet unsteady flow in a mixed-flow pump, mixed-flow pump models with tip clearances of 0.5 mm, 0.8 mm, and 1.1 mm were numerically calculated, and then the energy performance curves and internal flow structures were obtained and compared. The results show that the pump efficiency and the internal flow fields of numerical calculation are in good agreement with experimental results at design flow rate and near-stall condition. A portion of the positive slope segment appears in the energy performance curves under different tip clearances. The lowest head of the mixed-flow pump in the positive slope region decreases with the increase of the tip clearance while the highest head shows an opposite situation indicating that mixed-flow pumps are easier to stall under small tip clearance. At the design flow rate condition, the tip leakage vortex is relatively stable under different tip clearances and appears as a “snail shell” shape, whereas in rotating stall conditions, the “snail shell” shape disappear and the tip leakage flow on blade front forms a “flat” vortex structure. The inlet swirl flow not only affects the tip leakage flow in rotating stall conditions under different tip clearances, but also blocks the fluid from the inlet pipe. Under the circumstance of the same tip clearance, the main frequency amplitude of pressure pulsation coefficient gradually shifts away from blade passing frequency (96.67 Hz) to the axial frequency (24.17 Hz) when the pump operates in the stall condition.
Gravdahl JT. Modeling and control of surge and rotating stall in compressors. Dissertation, Norwegian University of Science and Technology, Norway, 1998.
2.
ChenXGuGMartinP, et al.Rotating stall control via bifurcation stabilization. Automatica1998; 34: 437–443.
3.
D'AndreaRBehnkenRLMurrayRM. Rotating stall control of an axial flow compressor using pulsed air injection. J Turbomach1997; 119: 742–752.
4.
KassimMSSalehFAKadhumMA. Experimental and numerical investigation of rotating stall phenomenon in centrifugal blower at different blade number of the impeller. J Eng Dev2015; 19: 31–49.
5.
DoddsJVahdatiM. Rotating stall observations in a high speed compressor—part I: experimental study. J Turbomach2015; 137: 051002-051002-051009.
6.
DoddsJVahdatiM. Rotating stall observations in a high speed compressor—part II: numerical study. J Turbomach2015; 137: 051003-051003-051010.
7.
ZhouP-JWangF-JYangZ-J, et al.Investigation of rotating stall for a centrifugal pump impeller using various SGS models. J Hydrodyn Ser B2017; 29: 235–242.
8.
HengYDazinAOuarzaziMN, et al.A study of rotating stall in a vaneless diffuser of radial flow pump. J Hydraul Res2018; 56: 494–504.
9.
YeWLuoXHuangR, et al.Investigation of flow instability characteristics in a low specific speed centrifugal pump using a modified partially averaged Navier–Stokes model. Proc IMechE, Part A: J Power and Energy2019.
10.
Takamine T, Watanabe S, Furukawa D, et al. Experimental investigation on diffuser rotating stall in a three-stage centrifugal pump. In: ASME 2017 fluids engineering division summer meeting, Waikoloa, Hawaii, USA, July 30 -August 3, 2017, pp.1–9.
11.
Lei C, Zhengwei W, Yexiang X, et al. Numerical investigation on the rotating stall characteristics in a three-blade centrifugal impeller. In: ASME 2016 international mechanical engineering congress and exposition, 2016, pp.1–7.
12.
LiWJiLLShiWD, et al.Correlation research of rotor–stator interaction and shafting vibration in a mixed-flow pump. J Low Freq Noise Vib Active Control2019, pp. 1–12.
13.
LiWJiLLShiWD, et al.Vibration of shaft system in the mixed-flow pump induced by the rotor-stator interaction under partial load conditions. Shock Vib2018, Article ID 2059784, pp.1–12. .
14.
LiWJiLLShiWD, et al.Fluid-structure interaction study of a mixed-flow pump impeller during startup. Eng Comput2018; 35: 1–17.
15.
LiWZhouLShiWD, et al.PIV experiment of the unsteady flow field in mixed-flow pump under part loading condition. Exp Therm Fluid Sci2017; 83: 191–199.
16.
LiWJiLLShiWD, et al.Effect of a nonuniform radial/axial tip clearance on the flow field in a mixed-flow pump. Strength Mater2018, 50: 137–145.
17.
LiWJiLLShiW, et al.Numerical calculation of internal flow field in mixed-flow pump with non-uniform tip clearance. Trans Chinese Soc Agric Mach2016; 47: 66–72.
18.
LiXYuanSPanZ, et al.Dynamic characteristics of rotating stall in mixed-flow pump. J Appl Math2013. Article ID 104629: 1–12.
19.
PanZYLiJJLiXJ, et al.Performance curve instability and rotating stall. Trans Chinese Soc Agric Mach2012; 43: 64–68.
20.
van Esch B and Cheng L. Unstable operation of a mixed-flow pump and the influence of tip clearance. In: Fluids engineering division summer meeting, ASME-JSME-KSME 2011 joint fluids engineering conference: Volume 1, Hamamatsu, Shizuoka, Japan, Parts A, 2011, pp.79–87.
21.
GotoA. The effect of tip leakage flow on part-load performance of a mixed-flow pump impeller. J Turbomach1992; 114: 383–391.
22.
LiuYTanLWangB. A review of tip clearance in propeller, pump and turbine. Energies2018; 11: 2202.
23.
LiuYBTanL. Tip clearance on pressure fluctuation intensity and vortex characteristic of a mixed flow pump as turbine at pump mode. Renew Energy2018; 129: 606–615.
24.
LiuYBTanL. Method of C groove on vortex suppression and energy performance improvement for a NACA0009 hydrofoil with tip clearance in tidal energy. Energy2018; 155: 448–461.
25.
LiuYBTanL. Spatial–temporal evolution of tip leakage vortex in a mixed-flow pump with tip clearance. J Fluids Eng2019; 141: 081302.
26.
TanLXieZFLiuYB, et al.Influence of T-shape tip clearance on performance of a mixed-flow pump. Proc IMechE, Part A: J Power and Energy2018; 232: 386–396.
27.
HaoYTanL. Symmetrical and unsymmetrical tip clearances on cavitation performance and radial force of a mixed flow pump as turbine at pump mode. Renew Energy2018; 127: 368–376.
28.
MiyabeMMaedaHUmekiI, et al.Unstable head-flow characteristic generation mechanism of a low specific speed mixed-flow pump. J Therm Sci2006; 15: 115–120.
29.
Schlechtriem S and Lötzerich M. Breakdown of tip leakage vortices in compressors at flow conditions close to stall. In: International gas turbine & aeroengine congress & exhibition, Orlando, FL, USA, 2–5 June 1997, pp.1–8.
30.
Hewkin-Smith M, Pullan G, Grimshaw SD, et al. The role of tip leakage flow in spike-type rotating stall inception. In: Conference: ASME Turbo Expo 2017: turbomachinery technical conference and exposition, Charlotte, North Carolina, USA, 26 June -30, June 2017, pp. 1–12.
31.
Cameron JD and Morris SC. Spatial correlation based stall inception analysis. In: Proceedings of ASME turbo expo 2007, Montreal, Canada, 2007, pp.433–444. New York: ASME.
32.
HoyingDATanCSVoHD, et al.Role of blade passage flow structures in axial compressor rotating stall inception. ASME J Turbomach1999; 121: 735–742.
33.
Vo H and Greitzer EM. Criteria for spike initiated rotating stall. ASME Paper No. GT2005-68374, 2005.
34.
MiyabeMFurukawaAMaedaH, et al.On improvement of characteristic instability and internal flow in mixed-flow pumps. J Fluid Sci Technol2008; 3: 732–743.
35.
Miyabe M, Furukawa A, Maeda H, et al. Rotating stall behavior in a diffuser of mixed-flow pump and its suppression. In: ASME 2008 fluids engineering division summer meeting collocated with the heat transfer, energy sustainability, and, energy nanotechnology conferences, Jacksonville, Florida, USA, 10 August -14 August 2008, pp.1147–1152.
36.
WeiBHWuKQ. Investigation into effect of tip clearance on inlet and outlet flow field of diagonal impeller with exit guide volute at near stall condition. J Eng Thermophys2000; 21: 5–8.
37.
LiRHuPLLiYB, et al.Numerical analysis of effect of blade tip clearance on pressure fluctuation in mixed-flow pump inlet. J Drain Irrig Mach Eng2015; 33: 560–565.
38.
Hewkin-SmithMPullanGGrimshawSD, et al.The role of tip leakage flow in spike-type rotating stall inception. J Turbomach2019; 141: 061010.
39.
ZhangDSWuSQShiWD, et al.Application and experiment of different turbulence models for simulating tip leakage vortex in axial flow pump. Trans Chinese Soc Agric Eng2013; 29: 46–53.
40.
RenYLiuHLShuMH, et al.Analysis of applicability of turbulence models in performance prediction for centrifugal pumps at the off-design conditions. Fluid Mach2012; 40: 18–22.
41.
YangXFYuYHLiuD, et al.Study of improvement of flow pattern in side-inlet pumping station based on SST k-ω turbulence model. J China Three Gorges Univ2018; 40: 1–4.
42.
Li W, Agarwal R, Ji LL, et al. Numerical simulation of incipient rotating stall characteristics in a mixed-flow pump. In: AIAA SciTech 2019, San Diego, CA, USA, 7–11 January 2019.
43.
Li W, Agarwal R, Zhou L, et al. Effect of tip clearance on rotating stall in a mixed-flow pump. In: Proceedings of ASME turbo expo 2019, Phoenix, AZ, USA, 17–21 June 2019.
44.
Menter FR. Zonal two equation k-ω turbulence models for aerodynamic flows. In: 24th fluid dynamics conference, Orlando, FL, USA, AIAA Paper-93–2906, July 1993.
Zhang R. Study on stall and cavitation flow characteristics and performance improvement of axial flow pump. PhD Thesis, Shanghai University, China, 2014.
