Multi-injection turbine housing for turbine performance improvement: A numerical and experimental analysis

Abstract

Secondary flow injection is a way which allows for the efficiency of a turbomachine to be increased further, after blade design optimizations have already been performed. In this paper, a novel method for improving turbine performance using secondary flow injection through an injection slot over the turbine shroud is investigated. Numerical simulations were conducted on a mixed-flow turbocharger turbine to test the effectiveness of secondary flow injection. An optimization was performed at peak efficiency at 50% turbine design speed to determine the injection setup which gives the highest turbine efficiency. Single-passage simulations for the optimized point showed an increase in efficiency of 2.6 percentage points compared to the baseline turbine. Flow analysis shows that injection partially blocks the flow passage near the blade tip, forcing turbine passage flow to migrate towards the hub. This apparently weakens the hub suction side separation vortex and reduces entropy generation from the vortex. Experimental testing was conducted and used for validation of full-stage turbine computational fluid dynamics (CFD) simulation results. Full-stage turbine CFD results show that with inlet nozzle vanes, secondary flow injection did not result in any visible improvement in the internal flow field and entropy generation, but overall efficiency can be improved by up to 2.28 percentage points at a velocity ratio of 0.75. Without nozzle vanes, however, secondary flow injection resulted in an efficiency improvement of up to 6.79 percentage points by weakening the hub suction side separation vortex and reducing its associated losses. Injection on the vaneless turbine configuration also resulted in a roughly 2 percentage point improvement in the peak turbine efficiency over the vaned turbine configuration. This might be due to more flow energy available to be extracted by the rotor from reduced losses due to the lack of nozzle vanes.

Keywords

Energy conversion/recovery internal combustion engines radial flow turbines turbines turbochargers turbomachinery aerodynamics turbomachinery flow

Get full access to this article

View all access options for this article.

References

Garett – Advancing Motion. Investor conference executive overview, New York City: Garrett Motion Inc., 2018.

Pesiridis

Martinez-Botas

. Experimental evaluation of active flow control mixed-flow turbine for automotive turbocharger application. J Turbomach 2007; 129: 44–52.

Hassan AF, Fuhrer C, Schatz M, et al. Multi-channel casing design for radial turbine operation control. In: 13th European conference on turbomachinery fluid dynamics and thermodynamics, Lausanne, Switzerland, 8–12 April 2019.

Denton

. The 1993 IGTI scholar lecture: loss mechanisms in turbomachines. J Turbomach 1993; 115: 621–656.

Yamamoto

. Endwall flow/loss mechanisms in a linear turbine cascade with blade tip clearance. J Turbomach 1989; 111: 264–275.

Schabowski

Hodson

. The reduction of over tip leakage loss in unshrouded axial turbines using winglets and squealers. J Turbomach 2014; 136: 041001–041001.

Rosic

Denton

. Control of shroud leakage loss by reducing circumferential mixing. J Turbomach 2008; 130: 021010–021010.

Praisner

Grover

Knezevici

, et al. Toward the expansion of low-pressure-turbine airfoil design space. J Turbomach 2013; 135: 061007–061007.

Bloxham

Bons

. Leading-edge endwall suction and midspan blowing to reduce turbomachinery losses. J Propul Power 2010; 26: 1268–1275.

10.

Behr

Kalfas

Abhari

. Control of rotor tip leakage through cooling injection from the casing in a high-work turbine. J Turbomach 2008; 130: 031014–031014.

11.

Benton

Bons

Sondergaard

. Secondary flow loss reduction through blowing for a high-lift front-loaded low pressure turbine cascade. J Turbomach 2013; 135: 021020–021020.

12.

Rezaeiha

Montazeri

Blocken

. Active flow control for power enhancement of vertical axis wind turbines: leading-edge slot suction. Energy 2019; 189: 116131–116131.

13.

Gad-el-Hak

. Flow control: passive, active, and reactive flow management, Cambridge: Cambridge University Press, 2000.

14.

Hunziker

Dickmann

Emmrich

. Numerical and experimental investigation of a centrifugal compressor with an inducer casing bleed system. Proc IMechE, Part A: J Power and Energy 2001; 215: 783–791.

15.

Tamaki

. Effect of recirculation device with counter swirl vane on performance of high pressure ratio centrifugal compressor. J Turbomach 2012; 134: 051036–051036.

16.

Chen

. Experimental investigation of end-wall VGJs in a compressor cascade. Appl Therm Eng 2018; 145: 386–395.

17.

Jiang

Lin

Yue

, et al. Aero-thermal optimization on multi-rows film cooling of a realistic marine high pressure turbine vane. Appl Therm Eng 2017; 111: 537–549.

18.

Wang

Song

Jianyang

, et al. Effect of cooling injection on the leakage flow of a turbine cascade with honeycomb tip. Appl Therm Eng 2018; 133: 690–703.

19.

Gao

Zheng

Dong

, et al. Control of tip leakage vortex breakdown by tip injection in unshrouded turbines. J Propul Power 2014; 30: 1510–1519.

20.

Sondergaard

Rivir

Bons

. Control of low-pressure turbine separation using vortex-generator jets. J Propul Power 2002; 18: 889–895.

21.

Volino

Ibrahim

. Separation control on high lift low-pressure turbine airfoils using pulsed vortex generator jets. Appl Therm Eng 2012; 49: 31–40.

22.

Niu

Zang

. Experimental and numerical investigations of tip injection on tip clearance flow in an axial turbine cascade. Exp Therm Fluid Sci 2011; 35: 1214–1222.

23.

Abidat

. Design and testing of a highly loaded mixed flow turbine, London: Imperial College London, 1991.

24.

Japikse D and Baines N. Introduction to turbomachinery. 1994. Concepts ETI.

25.

Bin Wan Salim

. Study of externally waste-gated turbine performance under steady and pulsating inlet conditions for improved turbocharger matching, London: Imperial College London, 2014.

26.

Whitfield

Baines

. Design of radial turbomachines, Harlow: Longman Scientific & Technical, 1990.

27.

Herwig

Kock

. Direct and indirect methods of calculating entropy generation rates in turbulent convective heat transfer problems. Heat Mass Transfer 2007; 43: 207–215.

28.

Newton P, Palenschat T, Martinez-Botas R, et al. Entropy generation rate in a mixed flow turbine passage. In: International gas turbine congress 2015, Tokyo, Japan, 15–20 November 2015.