Built-in Sensor Network for Structural Health Monitoring of Composite Structure

Abstract

By implementing a built-in sensor network on a composite structure, crucial information regarding the condition, damage state, and service environment of the structure can be obtained. In this study, methods for integrating piezoelectric sensor networks into a composite structure during different fabrication processes, including the resin transfer molding (RTM) and filament winding processes, are examined. To integrate sensor networks with different contours of structures, the method to fabricate a three-dimensional (3-D) diagnostic layer is developed. It is demonstrated that a large number of sensors supported on a thin flexible dielectric film, called a SMART Layer, offers a simple and efficient way to integrate a large sensor network onto a complex 3-D structure. The sensor network permanently embedded inside the composite structures can be used with either active sensing or passive sensing to monitor the health condition of a structure throughout its lifetime.

Keywords

sensor network composite structure structural health monitoring filament winding process RTM process

Get full access to this article

View all access options for this article.

References

Chang, F. 2002. “Ultra Reliable and Super Safe Structure for the New Century,” In: Daniel, L (ed.), In: Proc. of the 1st European Workshop on Structural Health Monitoring, Balageas, pp. 3–12.

Giurgiutiu, V. , Zagral, A. and Bao, J.J. 2002. “Piezoelectric Wafer Embedded Active Sensors for Aging Aircraft Structural Health Monitoring,” Structural Health Monitoring, 1(1): 41–61 .

Ikegami, R. 1999. “Structural Health Monitoring: Assessment of Aircraft Customer Needs,” In: Proceedings of the 2nd International Workshop on Structural Health Monitoring, Stanford, CA, September 8–10 .

Kessler, S.S. , Spearing, S.M. and Soutis, C. 2002. “Structural Health Monitoring in Composite Materials using Lamb Wave Methods,” Smart Materials and Structures, 11: 269–278 .

Liang, C. , Sun, F. and Rogers, C. 1994. “Coupled Electro-Mechanical Analysis of Adaptive Material Systems–Determination of the Actuator Power Consumption and System Energy Transfer,” Journal of Intelligent Material Systems and Structures, 5: 12–20 .

Lin, M. and Chang, F. 1998. “Design and Fabrication of Built-in Diagnostic for Composite Structures,” In: 12th American Society of Composites Technical Conference, Baltimore, USA.

Lin, M. , Kumar, A. , Beard, S. and Qing, X. 2001. “Built-in Structural Diagnostic with the SMART Layer and SMART Suitcase,” Smart Materials Bulletin, April 7–11.

Lin, M. and Chang, F. 2002. “The Manufacture of Composite Structures with a Built-in Network of Piezoceramics,” Composite Science and Technology, 62: 919–939 .

Lin, M. , Kumar, A. , Qing, X. , Beard, S. , Russell, S. and Walker, J. 2003. “Monitoring the Integrity of Filament Wound Structures using Built-in Sensor Networks,” In: Proceedings of SPIE on Smart Structures and Material Systems, Vol. 5054, March, pp. 222–229 .

10.

Mall, S. and Hsu, T.L. 2000. “Electromechanical Fatigue Behavior of Graphite/Epoxy Laminate Embedded with Piezoelectric Actuator,” Smart Materials and Structures, 9: 78–84 .

11.

Moulin, E. , Assaad, J. and Delebarre, C. 1997. “Piezoelectric Transducer Embedded in Composite Plate: Application to Lamb Wave Generation,” Journal of Applied Physics, 82(5): 2049–2055 .

12.

Paget, C.A. , Levin, K. and Delebarre, C. 2002. “Actuator Performance of Embedded Piezoceramic Transducer in Mechanically Loaded Composite,” Smart Materials and Structures, 11: 886–891 .

13.

Park, G. , Cudney, H. and Inman, D.J. 2000. “An Integrated Health Monitoring Technique using Structural Impedance Sensor,” Journal of Intelligent Material Systems and Structures, 11: 448–455 .

14.

Park, G. , Sohn, H. , Farrar, C.R. and Inman, D. 2003. “Overview of Piezoelectric Impedance-based Health Monitoring and Path Forward,” The Shock and Vibration Digest, 35(6): 451–463 .

15.

Qing, X. , Kumar, A. , Zhang, C. , Gonzalez, I.F. , Guo, G. and Chang, F.-K. 2005. “Hybrid Piezoelectric/Fiber Optic Diagnostic System for Structural Health Monitoring,” Smart Materials and Structures, 14(3): S98–S103 .

16.

Qing, X. , Beard, S. , Kumar, A. , Chan, H. and Ikegami, R. 2006a. “Advances in the Development of Built-in Diagnostic System for Filament Wound Composite Structures” , Composite Science and Technology, 66: 1694–1702 .

17.

Qing, X. , Chan, H. , Beard, S. and Kumar, A. 2006b. “An Active Diagnostic System for Structural Health Monitoring of Rocket Engines,” Journal of Intelligent Material Systems and Structures, 17: 619–628 .

18.

Russell, S. , Walker, J. and Workman, G. 2002. “Efficient Nondestructive Evaluation of Prototype Carbon Fiber Reinforced Structures,” In: Proceedings of the 10th US-Japan Conference on Composite Materials, Stanford, September 16–18 .

19.

Seydel, R. and Chang, F.K. 2001. “Impact Identification of Stiffened Composite Panel: I. System Development,” Smart Materials and Structures, 10: 354–369 .

20.

Shen, B.S. , Tracy, Y.S. and Chang, F.K. 1996. “Built-in Piezoelectrics for Processing and Health Monitoring of Composite Structures,” Journal of American Institute of Aeronautics and Astronautics, 1310: 390–397 .

21.

Staszewski, W.J. , Tomlinson, G. and Boller, C. 2003. Health Monitoring of Aerospace Structures: Smart Sensor Technologies and Signal Processing, John Wiley and Sons Ltd , December.

22.

Tang, S. , Xiong, K. , Liang, D. and Li, D. 2005. “The Development of SMART Layer Used in Structural Health Monitoring,” Journal of Experimental Mechanics (in Chinese), 20(2): 226–234 .

23.

Yang, S.M. , Hung, C.C. and Chen, K.H. 2005. “Design and Fabrication of a Smart Layer Module in Composite Laminated Structures,” Smart Materials and Structures, 14(2): 315–320 .