A Visco-hyperelastic Model for the Thermo-mechanical Behavior of Polymer Fibers

Abstract

A visco-hyperelastic model for the thermo-mechanical behavior of polymer yarns is presented. The model assumes that the stress in a yarn during uniaxial deformation results from the superposition of strain rate hardening effects and the softening caused by filament damage. The filament damage accounts for the fracture of polymer chains and the failure of inter-chain bonds. The constitutive model was implemented in the finite element method as a 1D rope element, and was applied to the study of nylon 6.6 and Kevlar^® 29 behavior. Numerical simulations of fabrics subjected to ballistic impact were performed, and the model is shown to predict the fabric penetration resistance and the deformation characteristics during the dynamic event.

Keywords

kevlar nylon damage impact polymer fiber.

Get full access to this article

View all access options for this article.

References

Bernstein, B. , Kearsley, A. and Zapas, L.J. ( 1965). A Study of Stress Relaxation with Finite Strain , Rubber Chemistry and Technology, 38: 76-89.

Cheng, M. and Chen, W. ( 2006). Modeling Transverse Behavior of Kevlar KM 2 Single Fibers with Deformation-induced Damage, International Journal of Damage Mechanics, 15: 121-132.

Dorfman, A. and Ogden, R.W. ( 2004). A Constitutive Model for the Mullins Effect with Permanent Set in Particle-reinforced Rubber, International Journal of Solids and Structures, 41: 1855-1878.

Godfrey, T.A. ( 2003). On Strain Localization in the High Rate Extension of Nylon Fibers, Journal of Material Science, 38: 4365-4371.

Holzapfel, G.A. , Stadler, M. and Odgen, R.W. ( 1999). Aspects of Stress Softening in Filled Rubber Incorporating Residual Strains, In: Dorfmann, A. and Muhr, A. (eds), Constitutive Models for Rubber, Rotterdam, A. A. Balkema Publishers, pp. 189-193.

Ivanov, I. and Tabiei, A. ( 2004). Loosely Woven Fabric Model with Viscoelastic Crimped Fibers for Ballistic Impact Simulations, International Journal of Numerical Methods Enginerring, 61: 1565-1583.

Javelin (2008). An In-house Finite Element Code, CAE Corporation.

Kaye, A. and Kennett, A.J. ( 1974). Constrained Elastic Recovery of a Polymeric Liquid After Various Shear Flow Histories, Rheologica Acta, 13: 916-923.

Lockett, F.J. ( 1972). Non-linear Viscoelastic Solids, New York, Academic Press Inc. Ltd.

10.

Odgen, R.W. and Roxburgh, D.G. ( 1999). A Pseudo-elastic Model for the Mullins Effect in Filled Rubber, Proceeding of the Royal Socity of London, A, 455: 2861-2877.

11.

Shahkarami, A. and Vaziri, R. ( 2007). A Continuum Shell Finite Element Model for Impact Simulation of Woven Fabrics, International Journal of Impact Engineering , 34: 104-109.

12.

Wagner, M.H. ( 1976). Analysis of Time-dependent Non-linear Stress Growth Data for Shear and Elongation Flow of a Low-density Branched Polyethylene Melt , Rheologica Acta, 15: 136-142.

13.

Wagner, M.H. , Raible, T. and Meissner, J. ( 1979). Tensile Stress Overshoot in Uniaxial Extension of a LDPE Melt, Rheologica Acta, 18: 427-428.

14.

Winter, H.H. ( 1978). On Network Models of Molten Polymers: Loss of Junctions Due to Stretching of Material Planes, Rheologica Acta, 17: 589-594.

15.

Wu, H.-C. ( 1992). An Energy Approach for Rope-strength Prediction , Journal of the Textiu Institute, 83: 542-543.

16.

Yang, L.M. , Shim, V.P.W. and Lim, C.T. ( 2000). A Visco-hyperelastic Approach to Modeling the Constitutive Behaviour of Rubber, International Journal of Impact Engineering , 24: 545-560.