Modelling and validation of a seat suspension with rubber spring for off-road vehicles

Abstract

To improve seat performance of low-frequency vibration isolation, this paper investigates a new type of seat suspension with a hollow composite rubber spring. To better describe the real system, a nonlinear suspension model was built. Then, the model parameters were identified and validated, the results show that the model is workable and the identified parameters are acceptable. The acceleration transmissibility of the new suspension was also analyzed by test and simulation. The resonant frequencies measured are close to the simulated under different excitation amplitudes, and all the relative deviations of the resonant frequency are less than 2.0%. Finally, in order to make clear how much the new suspension is better than the traditional suspension with the coil spring, the comparison of ride comfort was conducted under different working conditions. The results show that the new suspension can more effectively attenuate the low frequency from the uneven ground, meanwhile, it can provide a more stable support so that the driver can control the vehicle effectively. The model proposed can be used to predict the performance of the new seat suspension. The new suspension and the model provide a valuable reference for broadening the type of the seat suspension and exploring the optimal performance.

Keywords

Off-road vehicles seat suspension low frequency vibration isolation nonlinear characteristics

Get full access to this article

View all access options for this article.

References

Blood

Ploger

Yost

et al. (2010) Whole body vibration exposures in metropolitan bus drivers: A comparison of three seats. Journal of Sound and Vibration 329(1): 109–120.

Choi

Nam

Lee

(2000) Vibration control of a MR seat damper for commercial vehicles. Journal of Intelligent Material Systems and Structures 11(12): 936–944.

Demontis

Giacoletto

(2002) Prediction of car seat comfort from human-seat interface pressure distribution. SAE Technical Paper 2002-01-0781.

Zhang

(2013) Semi-active control of an integrated full-car suspension with seat suspension and driver body model using ER dampers. International Journal of Vehicle Design 63(2–3): 159–184.

Eger

Contratto

Dickey

(2013) Influence of driving speed, terrain, seat performance and ride control on predicted health risk based on ISO 2631-1 and EU Directive 2002/44/EC. Journal of Low Frequency Noise, Vibration and Active Control 30(4): 291–312.

Gad

Metered

Bassuiny

et al. (2015) Ride comfort enhancement of heavy vehicles using magnetorheological seat suspension. International Journal of Heavy Vehicle Systems 22(2): 93–113.

Griffin

(2012) Frequency-dependence of psychophysical and physiological responses to hand-transmitted vibration. Industrial Health 50(5): 354–369.

Han

Jung

Choi

et al. (2006) Ride quality investigation of an electrorheological seat suspension to minimize human body vibrations. Proceedings of the Institution of Mechanical Engineers Part D: Journal of Automobile Engineering 220(2): 139–150.

Holtz

Niekerk

(2010) Modeling and design of a novel air-spring for a suspension seat. Journal of Sound and Vibration 329(21): 4354–4366.

10.

International Organization for Standardization (1992) (1992) Mechanical vibration – laboratory method for evaluating vehicle seat vibration–Part 1: basic requirements. International Standard, ISO 10326-1, 1992, Geneva, Switzerland: International Organization for Standardization.

11.

Ahn

(2011) A vibration isolation system in low frequency excitation region using negative stiffness structure for vehicle seat. Journal of Sound and Vibration 330(26): 6311–6335.

12.

Lee

Goverdovskiy

(2012) A multi-stage high-speed railroad vibration isolation system with “negative” stiffness. Journal of Sound and Vibration 331(4): 914–921.

13.

Maciejewski

(2012) Control system design of active seat suspensions. Journal of Sound and Vibration 331(6): 1291–1309.

14.

Maciejewski

Krzyzynski

Meyer

(2014) Control system synthesis of seat suspensions used for protection of working machine operators. Vehicle System Dynamic 52(11): 1355–1371.

15.

Nguyen

Choi

Park

(2012) An analytical approach to optimally design of electrorheological fluid damper for vehicle suspension system. Meccanica 47(7): 1633–1647.

16.

Nguyen

Choi

(2015) A hybrid clustering based fuzzy structure for vibration control – Part 2: An application to semi-active vehicle seat-suspension system. Mechanical Systems and Signal Processing 56: 288–301.

17.

Park SJ, Lee YS, Nahm YE, et al. (1998) Seating physical characteristics and subjective comfort: design considerations. SAE Technical Paper 980653.

18.

Pope

Wilder

Magnusson

(1999) A review of studies on seated whole body vibration and low back pain. Proceedings of the Institution of Mechanical Engineers, Part H 213(6): 435–46.

19.

Stein

Múčka

Gunston

et al. (2008) Modelling and simulation of locomotive driver’s seat vertical suspension vibration isolation system. International Journal of Industrial Ergonomics 38(5–6): 384–395.

20.

Stein

Múčka

Gunston

(2009) A study of locomotive driver’s seat vertical suspension system with adjustable damper. Vehicle System Dynamics 47(3): 363–386.

21.

Shi

(2016) A nonlinear rubber spring model containing fractional derivatives for use in railroad vehicle dynamic analysis. Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit 230(7): 1745–1759.

22.

Sun

Yang

Deng

et al. (2015) Horizontal vibration reduction of a seat suspension using negative changing stiffness magnetorheological elastomer isolators. International Journal of Vehicle Design 68(1–3): 104–118.

23.

Tusset

Rafikov

Balthazar

(2009) An intelligent controller design for magnetorheological damper based on a quarter-car model. Journal of Vibration and Control 15(12): 1907–1920.

24.

Ulmer

(1995) Strain dependence of dynamic mechanical properties of carbon-black-filled rubber compounds. Rubber Chemistry and Technology 69(1): 15–47.

25.

Yan ZH, Zhu B, Li XF, et al. (2015) Modeling and analysis of static and dynamic characteristics of nonlinear seat suspension for off-road vehicles. Shock and Vibration Article ID 938205, 13 pages. Available at: https://www.hindawi.com/journals/sv/2015/938205/ (accessed).