Wetting of Polystyrene and Urethane Roof Insulations in the Laboratory and on a Protected Membrane Roof

Abstract

When subjected to a sustained temperature gradient in the presence of moisture in laboratory wetting tests, urethane and expanded polystyrene roof insulations accu mulate enough moisture to significantly reduce their insulating ability. Extruded polystyrene is quite resistant to moisture in such tests. But the vapor drive is not as great in actual roofs and it may reverse direction, thereby seasonally drying the msu lation. To determine how well the laboratory tests could predict the wetting rate of insulation in actual protected membrane roofs, extruded and expanded polystyrene and urethane insulations were installed in a protected membrane roof in Hanover, NH. After three years of exposure, little moisture had accumulated in the extruded polystyrene and it still retained essentially all of its initial insulating ability. Moisture progressively accumulated in 16 kg/m³ (1 pcf) and 30 kg/m³ (1.9 pcf) expanded poly styrene and at the end of the test they retained only about 30 and 40 percent of their initial thermal resistance respectively. The urethane accumulated enough moisture to reduce its insulating ability to about 30 percent of its dry value. The laboratory tests provided a valuable indication of the potential long-term moisture gain of these insu lations when installed in protected membrane roofs in cold regions.

Keywords

Roofs protected membranes thermal insulations cellular plastics urethane sty rene moisture wetting thermal conductivity thermal resistance.

Get full access to this article

View all access options for this article.

References

Schaefer, D. "Protected Membrane Roofing System Installation at Hanover, New Hampshire," Special Report 215. U.S. Army Cold Regions Research and Engineering Laboratory, Hanover, NH ( 1974).

Aamot, H.W.C. and D. Schaefer. "Protected Membrane Roofs in Cold Regions," CRREL Report 76-2. U.S. Army Cold Regions Research and Engineering Laboratory, Hanover, NH (1976).

Schaefer, D. "Water Absorption of Insulation in Protected Membrane Roofing Systems," CRREL Report 76-38. U.S. Army Cold Regions Research and Engineering Laboratory, Hanover, NH (1976).

Shaefer, D. , E.T. Larsen and H.W.C. Aamot. "Observation and Analysis of Protected Membrane Roofing Systems," CRREL Report 77-11. U.S. Army Cold Regions Research and Engineering Laboratory, Hanover, NH (1977).

Aamot, H.W.C. "Mid-Winter Installation of Protected Membrane Roofs in Alaska," CRREL Report 77-21. U.S. Army Cold Regions Research and Engineering Laboratory, Hanover, NH (1977).

Schaefer, D. "Installation of Loose-Laid Inverted Roof System at Ft. Wain-wright, Alaska," Special Report 77-18. U.S. Army Cold Regions Research and Engineering Laboratoiy, Hanover, NH (1977).

Best, J.S. U.S. Patent No. 3,411,256, Roof Construction and Method Thereof (1968).

Kaplar, C.W. "Moisture and Freeze-Thaw Effects on Rigid Thermal Insulations," Technical Report 249. U.S. Army Cold Regions Research and Engineering Laboratory , Hanover, NH (1974).

Dechow, F.J. and K.A. Epstein. "Laboratory and Field Investigations of Moisture Absorption and Its Effects on Thermal Performance of Various Insulations," in ASTM STP 660, Thermal Transmission Measurements of Insulation. Philadelphia, PA, pp. 234-260 (1978).

10.

Hedlin, C.P.

"Moisture Gains by Foam Plastic Roof Insulations Under Con trolled Temperature Gradients,"

Journal of Cellular Plastics, 13(5):313-319 (September/October, 1977).

11.

Tobiasson, W.N. and J. Ricard. "Moisture Gain and Its Thermal Consequence for Common Roof Insulations," in Proceedings 5th Conference on Roofing Technology, April 1979. National Roofing Contractors As ociation, Oak Park, IL, pp. 4-16 (1979)

12.

Knab, L.I. , D.R. Jenkins and R.G. Mathey. "The Effect of Moisture on the Thermal Conductivity of Roofing Systems," NBS Building Science Series 123. National Bureau of Standards , Gaithersburg, MD (1980).

13.

Hedlin, C.P. "Moisture Content in Protected Membrane Roof Insulations—Ef— fect of Design Features," in ASTM STP 603, Roofing Systems. Philadelphia, PA, pp. 36-50 (1976).