An investigation into the compressive properties of stainless steel micro-lattice structures

Abstract

This article presents a theoretical analysis for predicting the initial stiffness E*, and plastic collapse strength σ^* _pl of BCC micro-lattice blocks under compressive loading. This theoretical analysis is based on the observed deformation mechanisms, and can, in principle, be developed to predict the elastic properties of other micro-lattice structures. The analytical solutions are verified by comparing the predictions with FEM data using 1D beam and 3D solid elements and uniaxial compression tests on samples fabricated by selective laser melting. The FEM predictions using the 3D solid elements agree well with the experimental data for a wide range of strut aspect ratios, d/L. In addition, the range of applicability of the analytical model and the FEM predictions using beam elements are clarified.

Keywords

FEM micro-lattice mechanical properties plastic collapse

Get full access to this article

View all access options for this article.

References

Brooks WK , Todd J. and Sutcliffe CJ The production of open cellular lattice structures using selective laser melting . In: Sixth National Conference on Rapid Design, Prototyping and Manufacturing, CDRM/ Lancaster University, 2005.

Deshpande VS , Ashby MF and Fleck NA Foam topology bending versus stretching dominated architectures. Acta Mater 2001 ; 49: 1035-1040.

Deshpande VS , Fleck NA and Ashby MF Effective properties of the octet-truss lattice material. J Mech Phys Solids 2001 ; 49: 1747-1769.

Deshpande VS and Fleck NA Collapse of truss core sandwich beams in 3-point bending. Int J Solids Struct 2001 ; 38: 6275-6305.

Doyoyo M. and Hu JW Multi-axial failure of metallic strut-lattice materials composed of short and slender struts. Acta Mater 2005; 49: 1035-1040.

Kooistra GW , Deshpande VS and Wadley HNG. Compressive behavior of age hardenable tetrahedral lattice truss structures made from aluminium. Acta Mater 2004; 52: 4229-4237.

Krause DL , Whittenberger JD , Kantzos PT and Hebsur MG Mechanical testing of IN718 lattice block structures. In: Processing and Properties of Lightweight Cellular Metals and Structures , Seattle, 2002, pp. 233-242.

Liu JH and Lu TJ Multi-objective and multi-loading optimization of ultralightweight truss materials . Int J Solids Struct 2004 ; 41: 619-635.

McKown S. , Shen Y. , Brooks W. , Cantwell WJ , Sutcliffe C. , Langdon G. , et al. The quasi-static and blast response of lattice structures. Int J Impact Eng 2008 ; 35: 795-810.

10.

Mines RAW. On the characterization of foam and micro-lattice materials used in sandwich construction. Strain 2008; 44: 71-83.

11.

Mines RAW , McKown S. , Tsopanos S. , Shen E. , Cantwell WJ , Brookes W. , et al. Local effect during indentation of fully supported sandwich panels with micro-lattice cores. Appl Mech Mater 2008; 13-14: 85-90.

12.

Queheillalt DT and Wadley HNG. Cellular metal lattices with hollow trusses . Acta Mater 2005; 53: 303-313.

13.

Santorinaios M. , Brooks W. , Sutcliffe CJ and Mines RAW. Crush behaviour of open cellular lattice structures manufactured using selective laser melting . In: High performance structures and materials III. Southampton, UK: WIT Press , 2006 , pp.481-490.

14.

Sypeck DJ Cellular truss core sandwich structures. Appl Compos Mater 2005; 12: 229-246.

15.

Tsopanos S. , Mines RAW , McKown S. , Shen Y. , Cantwell WJ , Brooks W. and Sutcliffe CJ The influence of processing parameters on the mechanical properties of selectively laser melted micro-lattice structures . J Manuf Sci Eng (ASME) 2010: 132. DOI: 10.1115/1.4001743.

16.

Wallach JC and Gibson LJ Mechanical behavior of a three-dimensional truss material. Int J Solids Struct 2001; 38: 7181-7196.

17.

Wu X. Review of alloy and process development of TiAl alloys. Intermetallics 2006; 14: 1114-1122.

18.

Xie LS and Chan KC The effect of strut geometry on the yielding behaviour of open-cell form. Int J Mech Sci 2006; 48: 249-255.

19.

Zhang Y.H. Qiu XM and Fang DN Mechanical properties of two novel planar lattice structures. Int J Solids Struct 2008 ; 45: 3751-3768.

20.

Zhu HX , Knott JF and Mills NJ Analysis of the elastic properties of open-cell forms with tetrakaidecahedral cells. J Mech Phys Solid 1997; 45: 319-343.

21.

Zhou HX , Shrotriya P. and Soboyejo WO On the deformation of aluminum lattice block structures: from struts to structures . Mech Mater 2004; 36: 723-737.

22.

Klintworth JW and Stronge WJ Elastic-plastic yield limits and deformation laws for transversely crushed honeycombs. Int J Mech Sci 1988; 30-3/4: 273-292.

23.

Timoshenko SP and Gere JM Theory of elastic stability. New York: McGraw-Hill, 1961.

24.

Luxner MH , Stampfl J. and Petterman HE Finite element modeling concepts and linear analyses of 3D regular open cell structures. J Mater Sci 2005; 40: 5859-5866.

25.

Labeas G. and Sunaric M. Investigation on the static response and failure process of metallic open cellular structures. Strain 2010; 46: 195-204.

26.

Jones N. Structural impact. Cambridge, New York: Cambridge University Press, 1997.

27.

Mines RAW , McKown S. , Cantwell W. , Tsopanos S. , Brooks W. and Sutcliffe CJ On the progressive collapse of micro lattice structures. In: Proceedings of the 13th International Conference on Experimental Mechanics, Alexandroupolis, Greece, 2007, Paper No.158.

28.

ABAQUS Manual, 2007, HKS Inc.

29.

MSC.Marc Manual. MSC Software Corporation, 2008.

30.

Gibson LJ and Ashby MF Cellular solids: structure and properties . Cambridge , New York: Cambridge University Press, 1997.

31.

Stronge WJ and Yu TX Dynamic models for structural plasticity . Great Britain : Springer-Verlag , 1993 .

32.

Mines RAW , Girard Y. and Fascio V. On the development of conventional and micro lattice cellular metals as core materials in sandwich construction. In: Proceedings of SEICO 09 SAMPE European International Conference, 2009, pp. 248-255.