Mixed-elastohydrodynamic analysis of helical gears using load-sharing concept

Abstract

Helical gears are widely used in power transmission systems, and hence any improvement in their design and also the ability to predict their performance is of great importance. The key issues related to gears are their film thickness, which represents the lubricant ability to protect the surfaces from wear, and friction coefficient, which reflects the power loss. Since the pinion and gear mesh is usually under mixed-elastohydrodynamic lubrication, the effect of asperities should also be considered. The goal of this research is to present a model for predicting the performance of helical gears with consideration of surface roughness. Initially, the pinion and gear engagement analysis is performed considering non-uniform load distribution on gear’s tooth. In this model, each of the contact points on the gear flank is replaced with two cylinders, and lubrication analysis will be executed on these cylinders. The load-sharing concept has been employed to account for lubricant and surface roughness contribution in carrying the applied load. The predicted results are compared to other published data, and an acceptable agreement is seen. Acceptable accuracy, short execution time, and consideration of surface roughness are among the features of this model. It is shown that increasing the applied load results in an increase in the portion of the load that is carried by asperities as well as the friction coefficient.

Keywords

Helical gear friction coefficient load-sharing concept surface roughness

Get full access to this article

View all access options for this article.

References

Hains

Ollerton

. Contact stress distributions on elliptical contact surfaces subjected to radial and tangential forces. Proc Instn Mech Engrs 1963; 177: 95–114.

Majumdar

Hamrock

. Effect of surface-roughness on elastohydrodynamic line contact. Lubr Technol 1982; 104: 401–409.

Greenwood

Tripp

. The contact of two nominal flat rough surfaces. Proc Instn Mech Engrs 1970; 185: 625–633.

Ramsey

. Elastohydrodynamics, 2nd ed. London: Imperial College Press, 2001.

Hamrock

. Fundamentals of fluid film lubrication, New York: McGraw Hill, 1994.

Dowson

Higginson

. A theory of involute gear lubrication. In: Proceeding of a symposium organized by the mechanical tests of lubricants panel of the institute, institute of petroleum, gear lubrication, Brighton, UK, London: Elsevier, 1964, pp. 8–15.

Akin

. EHD lubricant film thickness formula for power transmission gears. J Lubr Technol 1974; 96: 426–431.

Simon

. Thermo-EHD analysis of lubrication of helical gears. J Mech Des 1988; 110: 330–336.

Sadeghi

Sui

. Thermal elastohydrodynamic lubrication of rolling/sliding contacts. J Tribol 1990; 112: 189–195.

10.

Sadeghi

Sui

. Thermal elastohydrodynamic lubrication of rough surfaces. J Tribol 1990; 112: 341–346.

11.

Bakolas

Mihailidis

. Analysis of rough line contacts operating under mixed EHL conditions. Lubr Sci 2003; 16: 153–168.

12.

Benedict GH and Kelly BW. Instantaneous coefficients of gear tooth friction. In: Transactions of ASLE, ASLE lubrication conference, Boston, MA, October, 1960, pp.57–70.

13.

Kelley

Lemanski

. Lubrication of involute gearing. Proc Instn Mech Engrs 1968; 182: 173–184.

14.

. Development of a generalized mechanical efficiency prediction methodology for gear pairs, PhD Dissertation, The Ohio State University, OH, 2005.

15.

Mihailidis

Bakolas

Panagiotidis

. Prediction of the friction coefficient of Spur Gear Pairs. VDI-Berichte Nr 2002; 1665: 705–719.

16.

Johnson

Greenwood

Poon

. A simple theory of asperity contact in elastohydrodynamic lubrication. Wear 1972; 19: 91–108.

17.

Akbarzadeh

Khonsari

. Performance of spur gears considering surface roughness and shear thinning lubricant. J Tribol 2008; 130: 1–8.

18.

Akbarzadeh

Khonsari

. Thermoelastohydrodynamic analysis of spur gears with consideration of surface roughness. Tribol Lett 2008; 32: 129–141.

19.

Zhang

Hsiang

. An adaptive finite element analysis for tooth deformation and load distribution of helical gears. Mech Aerosp Indus Eng 2008; 2: 1–16.

20.

Pedrero

Pleguezuelos

Artés

. Load distribution model along the line of contact for involute external gears. Mech Mach Theory 2010; 45: 780–794.

21.

Cruz

Chong

WWF

Teodorescu

. Transient mixed thermo-elastohydrodynamic lubrication in multi-speed transmissions. Tribol Int 2012; 49: 17–29.

22.

Moes

. Lubrication and beyond, Lecture notes. Enschede, The Netherlands: University of Twente, 1997.

23.

Gelinck

ERM

Schipper

. Calculation of stribeck curves for line contacts. Tribol Int 2000; 33: 175–180.

24.

Dowson

Higginson

. Elasto-hydrodynamic lubrication: the fundamentals of roller and gear lubrication, Oxford: Pergamon Press, 1966.

25.

Moes

. Optimum similarity analysis with applications to elastohydrodynamic lubrication. Wear 1992; 159: 57–66.

26.

Greenwood

Williamson

JBP

. Contact of nominally flat surfaces. Proc R Soc Lond Ser A 1966; 295: 300–319.

27.

Johnson

. Contact mechanics, Cambridge, UK: Cambridge University Press, 1985.

28.

Zhao

Maietta

Chang

. An asperity microcontact model incorporating the transition from elastic deformation to fully plastic flow. J Tribol 2000; 122: 86–93.

29.

Abbott

Firestone

. Specific surface quality a method based on accurate measurement and comparison. Mech Eng 1993; 55: 569–572.

30.

Hsu

Lee

. An efﬁcient algorithm for thermal elastohydrodynamic lubrication under rolling/sliding line contacts. J Tribol 1994; 116: 762–769.

31.

Roelands

CJA

Vlugter

Waterman

. The viscositytemperature-pressure relationship of lubricating oils and its correlation with chemical constitution. J Basic Eng 1962; 85: 601–610.