Performance comparison between textured,pocket,and tapered-land sector-pad thrust bearings using computational fluid dynamics thermohydrodynamic analysis

Abstract

Different geometry patterns of the surface of thrust bearings have been proven very beneficial in terms of bearing load-carrying capacity and friction coefficient. In this study, four different types of sector-pad thrust bearings have been cross-evaluated for operation under realistic operating conditions: (a) an open pocket bearing, (b) a closed pocket bearing, (c) a tapered-land bearing, and (d) a bearing partially textured with rectangular dimples. Bearing performance has been computed by means of computational fluid dynamics simulations based on the numerical solution of the Navier–Stokes and energy equations for incompressible flow. Conjugate heat transfer at the bearing pad and rotor has been taken into account. Initially, for a reference design of each bearing, the effects of varying rotational speed and minimum film thickness have been investigated. Further, characterization of each bearing for a constant level of thrust load has been performed. Finally, the effects of varying the depth of each geometry pattern have been studied. The present results illustrate a superior performance of the open pocket bearing in comparison to the other bearing types.

Keywords

Thrust bearing pocket tapered land artificial surface texturing thermohydrodynamic analysis computational fluid dynamics

Get full access to this article

View all access options for this article.

References

Rahmani

Mirzaee

Shirvani

. An analytical approach for analysis and optimisation of slider bearings with infinite width parallel textures. Tribol Int 2010; 43: 1551–1565.

Papadopoulos

Kaiktsis

Fillon

. CFD thermohydrodynamic analysis of 3-D sector-pad thrust bearings with rectangular dimples. ASME J Tribol 2014; 136: 011702–011702. 1–10.

Pascovici

Cicone

Fillon

. Analytical investigation of a partially textured parallel slider. Proc IMechE, Part J: J Engineering Tribology 2009; 223(2): 151–158.

Papadopoulos

Efstathiou

Nikolakopoulos

. Geometry optimization of textured 3-D micro-thrust bearings. ASME J Tribol 2011; 133: 041702–1–14.

Papadopoulos

Nikolakopoulos

Kaiktsis

. Characterization of stiffness and damping in textured sector-pad micro-thrust bearing using computational fluid dynamics. ASME J Eng Gas Turbines Power 2012; 134: 112502–112502. 1–9.

Rahmani

Shirvani

. Optimization of partially textured parallel thrust bearings with square-shaped micro-dimples. Tribol Trans 2007; 50: 401–406.

Cupillard

Cervantes

Glavatskih

. Pressure buildup mechanism in a textured inlet of a hydrodynamic contact. J Tribol 2008; 130(2): 21701: 1–10.

Marian

Kilian

Scholz

. Theoretical and experimental analysis of a partially textured thrust bearing with square dimples. Proc IMechE, Part J: J Engineering Tribology 2007; 221: 771–778.

Charitopoulos A, Fouflias D, Papadopoulos C, et al. Computational investigation of thermoelastohydrodynamic (TEHD) lubrication in a textured sector-pad thrust bearing. In: 12^th EDF/prime workshop, Futuroscope, France, 17–18 September 2013, pp.1–10.

10.

Papadopoulos C, Henry Y, Bouyer J, et al. Sector-pad thrust bearings with rectangular dimples: Comparison between experiments and CFD thermohydrodynamic simulations. In: World tribology congress 2013, Torino, Italy, 8–13 September 2013, pp.1–4.

11.

Henry

Bouyer

Fillon

. An experimental analysis of the hydrodynamic contribution of textured thrust bearings during steady-state operation: A comparison with the untextured parallel surface configuration. Proc IMechE, Part J: J Engineering Tribology 2014; 228(6): 1–14.

12.

Dobrica

Fillon

Pascovici

. Optimizing surface texture for hydrodynamic lubricated contact using a mass-conserving numerical approach. Proc IMechE, Part J: J Engineering Tribology 2010; 224: 737–750.

13.

Kazuyuki

Joichi

. Balancing wedge action: A contribution of textured surface to hydrodynamic pressure generation. Tribol Lett 2013; 50: 349–364.

14.

Heinrichson N. On the design of tilting-pad thrust bearings. PhD Thesis, Tehnical University of Denmark, Lyngby, 2006.

15.

Brajdic-Mitidieri

Gosman

Ioannides

Spikes

. CFD analysis of a low friction pocketed pad bearing. ASME J Tribol 2005; 127: 803–812.

16.

Etsion

Halperin

Brizmer

. Experimental investigation of laser surface textured parallel thrust bearings. Tribol Lett 2004; 17(2): 295–300.

17.

Etsion

. State of the art in laser surface texturing. J Tribology 2005; 127: 248–253.

18.

De Pellegrin

Hargreaves

. An isoviscous, isothermal model investigating the influence of hydrostatic recesses on a spring-supported tilting pad thrust bearing. Tribol Int 2012; 51: 25–35.

19.

Dobrica

Fillon

. Thermohydrodynamic behavior of a slider pocket bearing. J Tribol 2006; 128: 312–318.

20.

Dadouche

Fillon

Bligoud

. Experiments on thermal effects in a hydrodynamic thrust bearing. Tribol Int 2000; 33: 167–174.

21.

Dadouche

Fillon

Dmochowski

. Performance of a hydrodynamic fixed geometry thrust bearing: comparison between experimental data and numerical results. Tribol Trans 2006; 49: 419–426.

22.

Dobrica

Fillon

. About the validity of Reynolds equation and inertia effects in textured sliders of infinite width. Proc IMechE, Part J: J Engineering Tribology 2008; 223: 69–78.

23.

Frene

Nicolas

Degueurce

. Hydrodynamic lubrication: Bearings and thrust bearings, Amsterdam: Elsevier, 1997.

24.

Stachowiak

Batchelor

. Engineering tribology, 4th ed. Oxford: Butterworth Heinemann, 2013.