Parametric study on static and dynamic characteristics of bump-type gas foil thrust bearing for oil-free turbomachinery

Abstract

Gas foil bearings have bright application prospects in oil-free turbomachinery such as aircraft air cycle machines, compressors, and gas turbines. To extend the applicability of foil bearings to high-speed and heavy-load systems, the axial force produced primarily by the pressure difference between the turbine and compressor sides must be taken into consideration. The thrust disc of the rotor is typically used to sustain the axial force and maintain the attitude of the rotor in a rotor-bearing system. In an analytical model used to predict the performance of gas foil thrust bearings, fluid–structure interaction must be considered because of the coupling effects of hydrodynamic lubrication and the compliance of bearing surface. In this study, a link-spring structural model was employed to calculate the equivalent vertical stiffness of the bump foil. This model exhaustively considered the effect of three factors: flexibility of the bump foil, interactions between bumps and frictional forces at the contact surfaces. In addition, top foil deflection that directly affects film thickness is calculated using a finite-element shell model. The static and dynamic characteristics of gas foil thrust bearings were predicted after solving the steady-state Reynolds equation and two linearized dynamic coefficient equations which were obtained with perturbation method by using finite-difference method. The structural deformation equation was substituted into the Reynolds equations in the calculation process. The calculated static load was compared with the published experimental data, and the results validated the theoretical analysis. Thereafter, the static and dynamic characteristics including impact of rotational speed, initial minimum film thickness and the ratio of the inlet to outlet film thicknesses were analyzed. Parametric studies were also conducted to evaluate the effect of different structural parameters of the bump foil and journal tilting on the static characteristics of gas foil thrust bearings. Because the proposed analytical model is completely algebraic, it can be easily programmed for accurately and effectively investigating the performance of gas foil thrust bearings.

Keywords

Gas foil thrust bearing hydrodynamic lubrication static and dynamic characteristics parametric study journal inclination

Get full access to this article

View all access options for this article.

References

Agrawal

. Foil air/gas bearing technology—An overview. ASME paper 1997, pp. 347–347.

DellaCorte

Bruckner

. Remaining technical challenges and future plans for oil-free turbomachinery. J Eng Gas Turb Power 2011; 133: 042502–042502.

Feng

Kaneko

. A numerical calculation model of multi wound foil bearing with the effect of foil local deformation. J Syst Des Dyn 2007; 1: 648–659.

San Andrés

Chirathadam

Kim

T-H

. Measurement of structural stiffness and damping coefficients in a metal mesh foil bearing. J Eng Gas Turb Power 2010; 132: 032503–032503.

Somaya

Yoshimoto

Miyatake

. Load capacity of aerodynamic foil thrust bearings supported by viscoelastic material. Proc IMechE, Part J: J Engineering Tribology 2009; 223: 645–652.

DellaCorte

Radil

Bruckner

. Design, fabrication, and performance of open source generation I and II compliant hydrodynamic gas foil bearings. Tribol Trans 2008; 51: 254–264.

Bruckner

Prahl

. Analytic modeling of the hydrodynamic, thermal, and structural behavior of foil thrust bearings. NASA TM 2005, pp. 213811–213811.

Le Lez S, Arghir M and Frene J. A new bump-type foil bearing structure analytical model. In: ASME turbo expo 2007: Power for land, sea, and air, 2007, pp. 747–757. New York: ASME.

Feng

Kaneko

. Analytical model of bump-type foil bearings using a link-spring structure and a finite-element shell model. J Tribol 2010; 132: 021706–021706.

10.

San Andrés L and Kim TH. Improvements to the analysis of gas foil bearings: Integration of top foil 1D and 2D structural models. In: ASME turbo expo 2007: Power for land, sea, and air, 2007, pp. 779–789. New York: ASME.

11.

Walowit

Anno

. Modern developments in lubrication mechanics, London: Applied Science Publishers, 1975.

12.

Heshmat

Walowit

Pinkus

. Analysis of gas-lubricated foil journal bearings. J Lubric Technol 1983; 105: 647–655.

13.

C-PR

Heshmat

. Compliant foil bearing structural stiffness analysis: part I—Theoretical model including strip and variable bump foil geometry. J Tribol 1992; 114: 394–400.

14.

C-PR

Heshmat

. Structural stiffness and coulomb damping in compliant foil journal bearings: Theoretical considerations. Tribol Trans 1994; 37: 525–533.

15.

Iordanoff

. Analysis of an aerodynamic compliant foil thrust bearing: Method for a rapid design. J Tribology 1999; 121: 816–822.

16.

Carpino

Talmage

. A fully coupled finite element formulation for elastically supported foil journal bearings. Tribol Trans 2003; 46: 560–565.

17.

Carpino

Talmage

. Prediction of rotor dynamic coefficients in gas lubricated foil journal bearings with corrugated sub-foils. Tribol Trans 2006; 49: 400–409.

18.

Lee

Y-B

Park

D-J

Kim

C-H

. Operating characteristics of the bump foil journal bearings with top foil bending phenomenon and correlation among bump foils. Tribol Int 2008; 41: 221–233.

19.

Heshmat

Walowit

Pinkus

. Analysis of gas lubricated compliant thrust bearings. J Lubric Technol 1983; 105: 638–646.

20.

Iordanoff

. Maximum load capacity profiles for gas thrust bearings working under high compressibility number conditions. J Tribol 1998; 120: 571–576.

21.

Heshmat

. Analysis of gas lubricated foil thrust bearings using coupled finite element and finite difference methods. J Tribol 2000; 122: 199–204.

22.

Bruckner

. Simulation and modeling of the hydrodynamic, thermal, and structural behavior of foil thrust bearings, Cleveland, OH, USA: Case Western Reserve University, 2004.

23.

Park

D-J

Kim

C-H

Jang

G-H

. Theoretical considerations of static and dynamic characteristics of air foil thrust bearing with tilt and slip flow. Tribol Int 2008; 41: 282–295.

24.

Dykas

. Factors influencing the performance of foil gas thrust bearings for oil-free turbomachinery applications, Cleveland, OH, USA: Case Western Reserve University, 2006.

25.

Dickman

. An investigation of gas foil thrust bearing performance and its influencing factors, Cleveland, OH, USA: Case Western Reserve University, 2010.

26.

Hryniewicz

Wodtke

Olszewski

. Structural properties of foil bearings: A closed-form solution validated with finite element analysis. Tribol Trans 2009; 52: 435–446.

27.

Liu

Zhang

Cao

. Effects of shear stiffness in top foil structure on gas foil bearing performance based on thick plate theory. Proc IMechE, Part J: J Engineering Tribology 2013; 227: 761–776.

28.

Ruscitto

McCormick

Gray

. Hydrodynamic air lubricated compliant surface bearing for an automotive gas turbine engine. I, Latham, NY: Mechanical Technology, 1978.

29.

Kim

Lee

Y-B

Kim

. Rotordynamic performance of an oil-free turbo blower focusing on load capacity of gas foil thrust bearings. J Eng Gas Turb Power 2012; 134: 022501–022501.

30.

Peng

Z-C

Khonsari

. On the limiting load-carrying capacity of foil bearings. J Tribol 2004; 126: 817–818.

31.

Hamrock

Schmid

Jacobson

. Fundamentals of fluid film lubrication, Boca Raton: CRC Press, 2004.

32.

Peng

J-P

Carpino

. Calculation of stiffness and damping coefficients for elastically supported gas foil bearings. J Tribol 1993; 115: 20–27.

33.

Lee

Kim

. Design and performance prediction of hybrid air foil thrust bearings. J Eng Gas Turb Power 2011; 133: 042501–042501.

34.

Muszynska

. Rotordynamics, Boca Raton: CRC Press, 2010.

35.

Carpino

Peng

J-P

Medvetz

. Misalignment in a complete shell gas foil journal bearing. Tribol Trans 1994; 37: 829–835.

36.

Howard

. Misalignment in gas foil journal bearings: An experimental study. J Eng Gas Turb Power 2009; 131: 022501–022501.

37.

Dykas

Bruckner

Prahl

. Design, fabrication, and performance of foil gas thrust bearings for microturbomachinery applications. J Eng Gas Turb Power 2009; 131: 012301–012301.