Design and analysis of aerostatic spindle with high load characteristics for large ultra-precision drum lathe

Abstract

Aerostatic spindles offer low heat generation and high rotation accuracy, which make them an ideal choice for ultra-precision drum lathe, where extremely high motional accuracy and thermal stability are required. However, the limitations such as insufficient load capacity and stiffness have restricted their permissible application range and make them not suitable for large ultra-precision machine tools including drum lathe. In order to improve the load capacity and stiffness, this paper presents a high load capacity aerostatic spindle with pocketed orifice-type restrictors. Fluent is adopted and three-dimensional simulation models of aerostatic spindle with orifice and feeding pocket are set up to analyze the load characteristics. The simulation results show that this restrictor can enhance the throttling effect of orifice and suppress the pressure drop away from the orifice. Moreover, for aerostatic journal bearing, when eccentricity ratio is in the range of 0.2–0.3 and gas supply pressure is 0.6 MPa, carrying capacity and stiffness can reach up to 9499.4 N and 2813.1 N/μm. Finally, a group of loading experiments are carried out which prove that the novel three-dimensional simulation method is feasible and accurate to calculate the load characteristics of aerostatic spindles.

Keywords

Ultra-precision aerostatic spindle orifice-type restrictor carrying capacity stiffness

Get full access to this article

View all access options for this article.

References

Weck

Fischer

Vos

. Fabrication of microcomponents using ultraprecision machine tools. Nanotechnology 1997; 8: 145–148.

Luo

Cheng

Webb

. Design of ultraprecision machine tools with applications to manufacture of miniature and micro components. J Mater Process Technol 2005; 167: 515–528.

Park

Song

Hwang

. Development of an ultra precision machine tool for micromachining on large surfaces. Int J Precis Eng Manuf 2009; 10: 85–91.

Lee

Gao

Shimizu

. Precision measurement of carriage slide motion error of a drum roll lathe. Precis Eng 2012; 36: 244–251.

Lee

Gao

Shimizu

. Spindle error motion measurement of a large precision roll lathe. Int J Precis Eng Manuf 2012; 13: 861–867.

Lee

Shimizu

Gao

. Precision evaluation of surface form error of a large-scale roll workpiece on a drum roll lathe. Precis Eng 2014; 38: 839–848.

Wang

Tseng

. Analysis and fabrication of a prism film with roll-to-roll fabrication process. Opt Express 2009; 17: 4718–4725.

Ting

Chang

Chen

. Fabrication of an antireflective polymer optical film with subwavelength structures using a roll-to-roll micro-replication process. J Micromech Microeng 2008; 18: 1–9.

Song

Hwang

. An ultra-precision lathe for large-area micro-structured roll molds. J Korean Soc Precis Eng 2013; 30: 1303–1312.

10.

Moore Nanotechnology Systems, http://www.nanotechsys.com/machines/nanotech-hdl-2000-horizontal-drum-lathe/ (2010, accessed 20 March 2015)..

11.

Jeon

Park

. Improvement of machining quality of copper-plated roll mold by controlling temperature variation. Trans Nonferrous Met Soc China 2011; 21: 37–41.

12.

Liu

Zhang

. Performance analysis of rotating externally pressurized air bearings. Proc IMechE Part J: J Engineering Tribology 2009; 223: 653–663.

13.

Liu

Zhang

. Study of self-excited vibration for externally pressurized gas thrust bearing with circumferential groove. Lubr Eng 2010; 35: 9–12.

14.

Chen

. Effects of recess shapes on pneumatic hammering in aerostatic bearings. Proc IMechE Part J: J Engineering Tribology 2010; 224: 231–237.

15.

Yang

Chen

Kang

. Influence of orifices on stability of rotor-aerostatic bearing system. Tribol Int 2009; 42: 1206–1219.

16.

Yoshimoto

. Improvement of static characteristics of an aerostatic journal bearing using the elastic deformation of an O-ring. Tribol Int 1987; 20: 290–296.

17.

Fourka

Bonis

. Comparison between externally pressurized gas thrust bearings with different orifice and porous feeding systems. Wear 1997; 210: 311–317.

18.

Yoshimoto

Tozuka

Dambara

. Static characteristics of aerostatic porous journal bearings with a surface-restricted layer. Proc IMechE Part J: J Engineering Tribology 2003; 217: 125–132.

19.

Panzera

Rubio

Bowen

. Microstructural design of materials for aerostatic bearings. Cem Concr Compos 2008; 30: 649–660.

20.

Zhang

Liu

. Improvement on load performance of externally pressurized gas journal bearings by opening pressure-equalizing grooves. Tribol Int 2014; 73: 156–166.

21.

Long

Bao

. Entrance effect on load capacity of orifice compensated aerostatic bearing with feeding pocket. Chin J Mech Eng 2010; 23: 1–9.

22.

Fourka

Tian

Bonis

. Prediction of the stability of air thrust bearings by numerical, analytical and experimental methods. Wear 1996; 198: 1–6.

23.

Belforte

Raparelli

Viktorov

. Discharge coefficients of orifice-type restrictor for aerostatic bearings. Tribol Int 2007; 40: 512–521.

24.

Neves

Schwarz

Menon

. Discharge coefficient influence on the performance of aerostatic journal bearings. Tribol Int 2010; 43: 746–751.

25.

Dong

Ding

Liu

. On the analysis of aerostatic thrust bearings with the differential quadrature method. Proc IMechE Part J: J Engineering Tribology 2014; 228: 232–240.

26.

Pande

Somasundaram

. Effect of manufacturing errors on the performance of aerostatic journal bearings. Wear 1981; 66: 145–156.

27.

Khalil

El-Shorbagy

. Surface roughness effects on externally pressurized bearing performance. Wear 1985; 103: 1–10.

28.

Kwan

YBP

Post

. A tolerancing procedure for inherently compensated, rectangular aerostatic thrust bearings. Tribol Int 2000; 33: 581–585.

29.

Renn

Hsiao

. Experimental and CFD study on the mass flow-rate characteristic of gas through orifice-type restrictor in aerostatic bearings. Tribol Int 2004; 37: 309–315.

30.

Ding

. Influences of the geometrical parameters of aerostatic thrust bearing with pocketed orifice-type restrictor on its performance. Tribol Int 2007; 40: 1120–1126.