Based on the actual working condition of the cycloidal gear on the RV reducer, the maximum normal contact load of gear tooth and mesh tooth pair for varied quantity of plus equidistant modification and minus radial-moving modification were analyzed. By considering the macroscopic geometry, the contact load, and the real tooth surface roughness and transient effect of the contact area between pinwheel and cycloidal gear, a mixed lubrication model was established. The effects of normal load, curvature radius at the meshing point, fillet radius, as well as the speed on the lubrication condition were discussed. The results suggest that load, fillet radius, and speed have different degrees of influence on the lubricating conditions while the change of curvature radius in a small range has no significant effect on the lubrication, which also helps in the optimization of cycloidal gear tooth profile modification, therefore, to obtain better comprehensive performance of RV reducer.
DengJYChenJP. On the RV-AC drive in robots. In: IFAC IACA’ 95, Oxford: Elsevier Science Ltd, 1995, pp. 233–233.
2.
Cochran V and Bobak T. A methodology for identifying defective cycloidal reduction components using vibration analysis and techniques. In: AGMA, 08FTM02, 2008.
3.
LiLXHeWDLiXCycloidal-pinwheel transmission. In: ZhuXL (ed). Handbook of gear design, Beijing: Chemical Industry Press, 2005, pp. 766–872.
4.
Guan TM. Study on tooth-profile optimization method and correlative theory of FA cycloid drive. PhD Thesis, Dalian Jiaotong University, 2005.
5.
ChenBKFangTTLiCY. Gear geometry of cycloid drives. Sci China (Ser E Technol Sci)2008; 51: 598–610.
6.
LiLX. The modification manner for tooth profile and the analysis of forces on the cycloid disk of a cycloid speed reducer. J Dalian Railway Inst1984; 4: 29–40.
7.
GuanTMZhangDSLeiL. The analysis method of FA new-type pin-cycloidal gear planetary transmission and finite element analysis for tooth surface contact state. Mech Des2005; 3: 31–34.
8.
SunYSGuanTMZhangSL. Force simulation of cycloid gear of horizontal three-gear cycloid reducer. Appl Mech Mater2011; 66–68: 1993–1997.
9.
RenNZhuDChenWW. A three-dimensional deterministic model for rough surface line-contact EHL problems. ASME J Tribol2008; 131(1): 011501–011501.
10.
WangWZCaoHHuJB. Numerical simulation of transient elastohydrodynamic lubrication of helical gears. Tribology2011; 31: 604–609.
Zhu D and Hu YZ. The study of transition from full film elastohydrodynamic to mixed and boundary lubrication. In: The advancing frontier of engineering tribology, Proceedings of the 1999 STLE/ASME H.S. Cheng Tribology Surveillance, 1999, pp.150–156.
22.
HuYZZhuD. A full numerical solution to the mixed lubrication in point contacts. ASME J Tribol2000; 122: 1–9.
23.
YangPWenSZ. A generalized Reynolds equation for Non-Newtonian thermal elastohydrodynamic lubrication. ASME J Tribol1990; 112: 631–636.
24.
Roelands CJA. Correlational aspects of the viscosity-temperature-pressure relationship of lubricating oils. PhD Thesis, Technische Hogeschool Delft, The Netherlands.
25.
Ai XL. Numerical analysis of elastohydrodynamically lubricated line and point contacts with rough surfaces by using semi-system and multi-grid methods. PhD Thesis, Northwestern University, 1993.
26.
LiuSBWangQ. Studying contact stress fields caused by surface tractions with a discrete convolution and fast Fourier transform algorithm. ASME J Tribol2001; 124: 36–45.
27.
WangWZWangHLiuYC. A comparative study of the methods for calculation of surface elastic deformation. J Eng Tribol2003; 217: 145–152.
28.
ZhuDAiXL. Point contact EHL based on optically measured three-dimensional rough surfaces. ASME J Tribol1997; 119: 375–384.
29.
ZhuDLiuYCWangQ. On the numerical accuracy of rough surface EHL solution. Tribol Trans2014; 57: 570–580.
