A semianalytical method for studying the performances of aerostatic thrust bearing

Abstract

The solution of Reynolds equation and computational fluid dynamics are widely employed for the lubrication performance analysis of aerostatic thrust bearing. However, the solution of Reynolds equation may be inaccurate and cannot present detailed performance near orifice, while computational fluid dynamics method has low computational efficiency with time consumption in mesh generation and solving Navier–Stokes equations. In order to overcome the drawbacks of Reynolds equation and computational fluid dynamics, based on the method of separation of variables, a semianalytical method is developed for describing the characteristics of aerostatic bearings available. The method of separation of variables considering the initial and viscous effect is more accurate than the Reynolds equation and can present detailed performance near orifice in the aerostatic thrust bearings, while method of separation of variables has great computational efficiency compared to computational fluid dynamics. Meanwhile, the pressure distribution calculated by method of separation of variables is compared to the published experimental data and the results obtained by computational fluid dynamics. The comparative results indicate validity of the method. Furthermore, the influences of flow and geometry parameters, such as supply pressure, orifice diameter, film thickness, and bearing radius, on the characteristics of aerostatic thrust bearings with single orifice are studied. The results show that there exists pressure depression phenomenon near orifice. The depression phenomenon is strengthened with increase of film thickness and supply pressure and decrease of orifice diameter and bearing radius, while the maximum speed increases with strengthening of pressure depression due to decrease of minimum local pressure near orifice. Moreover, the bearing capacity increases with increase of supply pressure, orifice diameter, and bearing radius and decreases with increase of film thickness, while mass flow rate increases with supply pressure, orifice diameter, and film thickness and it is not sensitive to bearing radius.

Keywords

Aerostatic thrust bearing pressure depression semianalytical method pressure distribution speed distribution

Get full access to this article

View all access options for this article.

References

Liu

Chen

. Aerostatic lubrication, Harbin: Harbin Institute of Technology, 1990.

Liu

Teo

Epstein

et al.

Hydrostatic gas journal bearings for micro-turbomachinery. J Vib Acoust 2005; 127: 157–164.

Colombo

Raparelli

Viktorov

. Externally pressurized gas bearings: a comparison between two supply holes configurations. Tribol Int 2009; 42: 303–310.

Belforte

Raparelli

Viktorov

et al.

Discharge coefficients of orifice-type restrictor for aerostatic bearings. Tribol Int 2007; 40: 512–521.

Chen

Huo

Cui

et al.

Investigation the gas film in micro scale induced error on the performance of the aerostatic spindle in ultra-precision machining. Mech Syst Signal Process 2018; 105: 488–501.

Liu

Zhang

. Performance analysis of rotating externally pressurized air bearings. Proc IMechE, Part J: J Engineering Tribology 2009; 223: 653–663.

Dal

Karaçay

. Effects of angular misalignment on the performance of rotor-bearing systems supported by externally pressurized air bearing. Tribol Int 2017; 111: 276–288.

Wang

Huang

et al.

Effects of journal rotation and surface waviness on the dynamic performance of aerostatic journal bearings. Tribol Int 2017; 112: 1–9.

Wang

et al.

Effect of surface waviness on the static performance of aerostatic journal bearings. Tribol Int 2016; 103: 394–405.

10.

Ding

. Design analysis and experimental study of aerostatic linear guideways used in a high acceleration and high precision xy stage. Proc IMechE, Part J: J Engineering Tribology 2007; 221: 1–9.

11.

Morosi

Santos

. On the modelling of hybrid aerostatic-gas journal bearings. Proc IMechE, Part J: J Engineering Tribology 2011; 225: 641–653.

12.

Dong

Ding

Liu

et al.

On the analysis of aerostatic thrust bearings with the differential quadrature method. Proc IMechE, Part J: J Engineering Tribology 2014; 228: 232–240.

13.

Rajput

Sharma

. Analysis of externally pressurized multirecess conical hybrid journal bearing system using micropolar lubricant. Proc IMechE, Part J: J Engineering Tribology 2013; 227: 943–961.

14.

Chen

et al.

Effects of recess shapes on pneumatic hammering in aerostatic bearings. Proc IMechE, Part J: J Engineering Tribology 2010; 224: 231–237.

15.

Chen

Zhou

Han

et al.

Characteristics evaluation of gas film in the aerostatic thrust bearing within rarefied effect. Proc IMechE, Part J: J Engineering Tribology 2017; 231: 149–157.

16.

Ding

. A simplified calculation method on the performance analysis of aerostatic thrust bearing with multiple pocketed orifice-type restrictors. Tribol Int 2012; 56: 66–71.

17.

Chen

et al.

Aerostatic thrust bearing performances analysis considering the fluid-structure coupling effect. Proc IMechE, Part J: J Engineering Tribology 2016; 230: 1588–1596.

18.

Renn

J-C

Hsiao

C-H

. Experimental and CFD study on the mass flow-rate characteristic of gas through orifice-type restrictor in aerostatic bearings. Tribol Int 2004; 37: 309–315.

19.

Ding

. Influences of the geometrical parameters of aerostatic thrust bearing with pocketed orifice-type restrictor on its performance. Tribol Int 2007; 40: 1120–1126.

20.

Zhao

Zhu

et al.

Numerical analysis and experimental study on the microvibration of an aerostatic thrust bearing with a pocketed orifice-type restrictor. Proc IMechE, Part J: J Engineering Tribology 2015; 229: 609–623.

21.

Chen

X-D

X-M

. The effect of the recess shape on performance analysis of the gas-lubricated bearing in optical lithography. Tribol Int 2006; 39: 1336–1341.

22.

Chen

Luo

et al.

Air vortices and nano-vibration of aerostatic bearings. Tribol Lett 2011; 42: 179–183.

23.

Gao

Cheng

Chen

et al.

CFD based investigation on influence of orifice chamber shapes for the design of aerostatic thrust bearings at ultra-high speed spindles. Tribol Int 2015; 92: 211–221.

24.

Huang M, Cui H, Liu P, et al. A theoretical and experimental study on the stiffness of aerostatic thrust bearings with vacuum preloading. Proc IMechE, Part J: J Engineering Tribology. 2019; 233: 256–270.

25.

Zhou

Chen

. A hybrid approach to the numerical solution of air flow field in aerostatic thrust bearings. Tribol Int 2016; 102: 444–453.

26.

Zhang

Zou

et al.

A numerical method for solution of the discharge coefficients in externally pressurized gas bearings with inherent orifice restrictors. Tribol Int 2018; 125: 156–168.