Flow factor modeling of combustion engine ring and cylinder components in mixed hydrodynamic lubrication

Abstract

This work employees the modification of the Reynolds equation for computational efficiency by analyzing rough surfaces in the hydrodynamic flow regime through the use of flow factors. This analysis is aimed towards modeling the surface interactions and pressure variations across power cylinder components of an internal combustion engine, namely the piston ring and cylinder wall. The Patir and Cheng equations are for general surfaces that accounts for the overall effect of roughness and anisotropic structure. However, rough surfaces are not fully characterized by these two parameters and therefore the aim of this paper was to provide flow-factors specific to the cross-hatched cylinder liner surfaces and piston ring interface. These interacting surfaces were measured directly through the use of a profilometer. Average flow factors are derived via full deterministic solution of the Reynolds equation over rough surfaces to model the pressure and shear variations relative to smooth surfaces. These flow factors can then be used to consider the effect of roughness in lubrication problems without deterministically modeling roughness.

Keywords

flow factors reynolds equation hydrodynamic lubrication surface characterization auto-correlation function cross-correlation function rough surfaces smooth surfaces predictive modeling piston ring cylinder wall

Get full access to this article

View all access options for this article.

References

Michelberger

, et al. Combined measurement and simulation of piston ring cylinder liner contacts with a reciprocating long-stroke tribometer. Tribol Int 2021; 163: 107146.

Spencer

, et al. An experimental and numerical investigation of frictional losses and film thickness for four cylinder liner variants for a heavy duty diesel engine . Proc Inst Mech Eng, Part J: J Eng Tribol 2013; 227: 1319–1333.

Cheong

, et al. High-resolution LIF-Imaging of the oil film thickness in the piston-ring/cylinder-liner contact in an optical tribometer . Tribol Int 2020; 147: 106230.

Wigger

, et al. Quantitative two-dimensional measurement of oil-film thickness by laser-induced fluorescence in a piston-ring model experiment. Appl Opt 2016; 55: 269–279.

Mishra

Rahnejat

King

. Tribology of the ring—bore conjunction subject to a mixed regime of lubrication . Proc Inst Mech Eng, Part C: J Mech Eng Sci 2009; 223: 987–998.

Patir

Cheng

. An average flow model for determining effects of three-dimensional roughness on partial hydrodynamic lubrication. ASME J. Tribol 1978; 100: 12–17.

Peklenik

. Paper 24: new developments in surface characterization and measurements by means of random process analysis. In: Proceedings of the institution of mechanical engineers, conference proceedings. London, England: Sage Publications Sage UK, 1967, pp. 108–126.

Leighton

Rahmani

Rahnejat

. Surface-specific flow factors for prediction of friction of cross-hatched surfaces. Surf Topogr: Metrol Prop 2016; 4: 025002.

Wilson

Marsault

. Partial hydrodynamic lubrication with large fractional contact areas. 1998.

10.

Peeken

, et al. On the numerical determination of flow factors. 1997.

11.

Zheng

. Some aspects of determining the flow factors. 1989.

12.

Morales-Espejel

. Flow factors for non-Gaussian roughness in hydrodynamic lubrication: an analytical interpolation. Proc Inst Mech Eng, Part C: J Mech Eng Sci 2009; 223: 1433–1441.

13.

Sahlin

, et al. A mixed lubrication model incorporating measured surface topography. Part 1: theory of flow factors. Proc Inst Mech Eng, Part J: J Eng Tribol 2010; 224: 335–351.

14.

Spencer

Almqvist

Larsson

. A numerical model to investigate the effect of honing angle on the hydrodynamic lubrication between a combustion engine piston ring and cylinder liner. Proc Inst Mech Eng, Part J: J Eng Tribol 2011; 225: 683–689.

15.

Tripp

. Surface roughness effects in hydrodynamic lubrication: the flow factor method. J Lubr Technol 1983; 105: 458–463.

16.

Elrod

. A general theory for laminar lubrication with Reynolds roughness. 1979.

17.

Lunde

Tonder

. Pressure and shear flow in a rough hydrodynamic bearing, flow factor calculation. 1997.

18.

Tzeng

Saibel

EJAT

. Surface roughness effect on slider bearing lubrication. ASLE Trans 1967; 10: 334–348.

19.

Patir

Cheng

. Application of average flow model to lubrication between rough sliding surfaces. ASME J. Tribol 1979; 101: 220–230.

20.

Patir

. Effects of surface roughness on partial film lubrication using an average flow model based on numerical simulation[Ph. D. Thesis]. 1978.

21.

Locker

. Use of surface specific flow factors in a multi-physical model of power cylinder components. 2018.

22.

Patir

NJW

. A numerical procedure for random generation of rough surfaces. Wear 1978; 47: 263–277.

23.

W-L

Chien

. Parameters for roughness pattern and directionality . Tribol Lett 2004; 17: 547–551.

24.

Dodds

Robson

. The description of road surface roughness. J Sound Vib 1973; 31: 175–183.