The use of response surface methodology in cryrolling of ultrafine grained Al6061 to improve the mechanical properties

Abstract

In this paper, mechanical properties of Al6061 alloy sheets severely deformed by the cryorolling process are investigated using response surface methodology. Four control parameters including the total thickness reduction, aging temperature, aging time, and short annealing temperature are selected as the influencing parameters. The influence of these parameters on the mechanical behavior of processed samples is studied through the measurement of yield strength, ultimate tensile strength, ductility, and hardness. Analysis of variance showed that the experimental and predicted values are in good agreement and the response surface methodology could be effectively applied in the cryorolling processing for finding an economical and optimum condition to achieve simultaneous improvement in the strength and the ductility of Al6061 alloy. After short annealing of the cryorolling specimens (with 90% total thickness reduction) at 205℃ for 5 min followed by aging at 148℃ for 39 h, the yield strength, the ultimate tensile strength, and the hardness, increased by 24%, 20%, and 40% respectively compared with unprocessed Al6061 alloy and the ductility of 12% was obtained. The results of X-ray diffraction analysis confirm the evolution of precipitates which are consistent with the measured hardness and tensile properties. Also, fractography analyses of fracture surfaces for bulk Al6061, cryorolled and post aging tensile specimens are performed using scanning electron microscopic images.

Keywords

Cryorolling response surface methodology mechanical properties Al6061 alloy aging short annealing

Get full access to this article

View all access options for this article.

References

Valiev

Islamgaliev

Alexandrov

. Bulk nanostructured materials from severe plastic deformation. Prog Mater Sci 2000; 45: 103–189.

Valiev

Krasilnikov

Tsenev

. Plastic deformation of alloys with submicron-grained structure. Mater Sci Eng A 1991; 137: 35–40.

Valiev

Langdon

. Principle of equal channel angular pressing as a processing tool for grain refinement. Prog Mater Sci 2006; 51: 881–981.

Sakai

Horita

Langdon

. Grain refinement and superplasticity in an aluminum alloy processed by high-pressure torsion. Mater Sci Eng A 2005; 393: 344–351.

Harai

Ito

Horita

. High pressure torsion using ring specimens. Scripta Mater 2008; 58: 469–482.

Saito

Utsunomiya

Tsuji

. Novel ultra-high straining process for bulk materials-development of the accumulative roll-bonding process. Acta Mater 1999; 47: 579–583.

Tsuji

Saito

Utsunomiya

. Ultra-fine grained bulk steel produced by accumulative roll bonding (ARB) process. Scripta Mater 1999; 40: 795–800.

Koch

Morris

. Ductility of nanostructured materials. MRS Bull 1999; 24: 54–58.

Koch

. Ductility in nanostructured and ultra fine-grained materials: Recent evidence for optimism. J Metastable Nanocrystal Mater 2003; 18: 9–20.

10.

Wang

Chen

Zhou

. High tensile ductility in a nanostructured metal. Nature Mater 2002; 419.

11.

Humphreys

Hatherly

. Recrystallization and related annealing phenomena, Oxford: Pergamon Press, 1996.

12.

Totten

MacKenzie

. Handbook of aluminium: Physical metallurgy and processes, New York: Marcel Dekker, 2003.

13.

Polmear

. Light alloys: Metallurgy of the light metals, London: Arnold, 1995.

14.

Lloyd

. The scaling of the tensile ductile fracture strain with yield strength in Al alloys. Scripta Mater 2003; 48: 341–344.

15.

Panigrahi

Jayaganthan

. Development of ultrafine grained Al-Mg-Si alloy with enhanced strength and ductility. J Alloy Compd 2009; 470: 285–288.

16.

Angella

Bassani

Tuissi

. Ageing behavior and mechanical properties of a solution treated and ECAP processed 6082 alloy. MaterTrans 2004; 45: 2282–2287.

17.

Rangaraju

Raghuram

Krishna

. Effect of cryorolling and annealing on microstructure and properties of commercially pure aluminum. Mater Sci Eng A 2005; 398: 246–251.

18.

Lee

Shin

Park

. Effect of annealing temperature on microstructure and mechanical properties of a 5083 Al alloy deformed at cryogenic temperature. Scripta Mater 2004; 51: 355–359.

19.

Lee

Chang

Kao

. The tensile behavior and deformation microstructure of cryo-rolled and annealed pure nickel. Mater Sci Eng A 2005; 408: 131–135.

20.

Panigrahi

Jayaganthan

. A study on the mechanical properties of cryorolled Al–Mg–Si alloy. Mater Sci Eng A 2008; 480: 299–305.

21.

Panigrahi

Jayaganthan

Pancholi

. Effect of plastic deformation conditions on microstructural characteristics and mechanical properties of Al 6063 alloy. Mater Design 2009; 30: 1894–1901.

22.

Panigrahi

Jayaganthan

. Influence of solutes and second phase particles on work hardening behavior of Al 6063 alloy processed by cryorolling. Mater Sci Eng A 2011; 528: 3147–3160.

23.

Panigrahi

Devanand

Jayaganthan

. Effect of ageing on strength and ductility of ultrafine grained Al 6061 alloy. Mater Sci Forum 2010; 633–634: 303–309.

24.

Panigrahi

Jayaganthan

. A study on the combined treatment of cryorolling, short-annealing, and aging for the development of ultrafine-grained Al 6063 alloy with enhanced strength and ductility. Metall Mater Trans A 2010; 41A: 2675–2690.

25.

Panigrahi

Jayaganthan

. Development of ultrafine grained Al–Mg–Si alloy with enhanced strength and ductility. J Alloy Compd 2009; 470: 285–288.

26.

Rao

Panigrahi

Jayaganthan

. Effect of annealing and aging treatment on mechanical properties of ultrafine grained Al 6061 alloy. Mater Sci Technol 2010; 26: 371–374.

27.

Montgomery

. Design and analysis of experiments, New York: Wiley, 1997.

28.

Myers

Montgomery

. Response surface methodology: Process and product optimization using designed experiments, New York: Wiley, 2002.

29.

Anderson

Whitcomb

. DOE simplified: Practical tools for effective experimentation, New York: Productivity Inc., 2000.

30.

Kilickap

. Modeling and optimization of burr height in drilling of Al-7075 using Taguchi method and response surface methodology. Int J Adv Manuf Technol 2010; 49: 911–923.

31.

Agarwal

Singh

Kumar

. Optimizing power consumption for CNC turned parts using response surface methodology and Taguchi’s technique - a comparative study. J Mater Process Technol 2008; 200: 373–384.

32.

Konkova

Mironov

Korznikov

. Microstructural response of pure copper to cryogenic rolling. Acta Mater 2010; 58: 5262–5273.

33.

Panigrahi

Jayaganthan

. Development of ultrafine-grained Al6063 alloy by cryorolling with the optimized initial heat treatment conditions. Mater Design 2011; 32: 2172–2180.

34.

Gabriel

. Scanning electron microscopy, ASM Handbooks. Metals Park, OH: ASM International, 1998.