Analysis of electrochemical behavior on micro-drilling of cast hybrid Al/(Al 2 O 3p + SiC p + C p )-MMC using micro-ECM process

Abstract

This paper presents the results of an experimental investigation on machining of micro-hole during electrochemical micromachining (ECMM) of stir-cast hybrid aluminum/(alumina + silicon carbide + carbon particulates) metal matrix composite. An ECMM set-up was developed and utilized for carrying out the experimental investigation. The supply current (Ip), supply voltage (v), pulse-on time (Ton), pulse-off time (Toff), electrolyte concentration (EC), and electrolyte flow rate (FR) were selected as process parameters. The effect of process parameters on material removal rate (MRR), electrode wear rate (EWR), surface roughness height (SR), taper cut (TC), over cut (OC), and micro-spark-affected zone (MSAZ) were analyzed through various graphs. The surface characteristics of the micro-drilled holes were analyzed using energy dispersive X-ray spectroscopy and scanning electron microscope techniques. Experimental results revealed that the MRR, EWR, TC, OC, and MSAZ increase with an increase in supply current, voltage, and pulse-on time. The optimal parametric combination for high MRR with low TC, OC, and MSAZ was found at 1.5 A supply current, 13 V supply voltage, 10 µs pulse-on time, 10 µs pulse-off time, 15 g/L electrolyte concentration, and 0.2 L/min electrolyte flow rate.

Keywords

electrochemical micromachining metal removal rate taper cut over cut

Get full access to this article

View all access options for this article.

References

Suresh

Mortensen

Needleman

. Fundamentals of metal matrix composites, Stoneham, MA: Butterworth-Heinemann, 1993.

Meena

Manna

Banwait

et al.

An analysis of mechanical properties of the developed Al/SiC-MMCs. Am J Mech Eng 2013; 1: 14–19.

Manna

Bhaattacharrya

. A study on machinability of Al/SiC-MMC. Int J Mater Process Technol 2003; 140: 711–716.

Bhattacharyya

Mitra

Boro

. Electrochemical machining: new possibilities for micromachining. Robot CIM Int Manuf 2002; 18: 283–289.

Bhattacharyya

Munda

. Experimental investigation on the influence of electrochemical machining parameters on machining rate and accuracy in micromachining domain. Int J Mach Tools Manuf 2003; 43: 1301–1319.

Zheng

Yang

et al.

Localized electrochemical micromachining with gap control. Sens Actuat 2003; 108: 144–148.

Kurita

Chikamori

Kubota

et al.

A study of three-dimensional shape machining with an ECµM system. Int J Mach Tools Manuf 2006; 46: 1311–1318.

Fan

Z-w

Hourng

L-W

. Electrochemical micro-drilling of deep holes by rotational cathode tools. Int J Adv Manuf Technol 2011; 52: 555–563.

Chiou

Y-C

Lee

R-T

Chen

T-J

et al.

Fabrication of high aspect ratio micro-rod using a novel electrochemical micro-machining method. Precis Eng 2012; 36: 193–202.

10.

Ghoshal

Bhattacharyya

. Influence of vibration on micro-tool fabrication by electrochemical machining. Int J Mach Tools Manuf 2013; 64: 49–59.

11.

Choi

Kim

Shin

et al.

Analysis of the electrochemical behaviors of WC–Co alloy for micro ECM. J Mater Process Technol 2013; 213: 621–630.

12.

Senthilkumar

Ganesan

Karthikeyan

. Study of electrochemical machining characteristics of Al/SiCp composites. Int J Adv Manuf Technol 2009; 43: 256–263.

13.

Sankar

Gnanavelbabu

Rajkumar

. Effect of reinforcement particles on the abrasive assisted electrochemical machining of Aluminium-Boron Carbide-Graphite composite. Procedia Eng 2014; 97: 381–389.

14.

Liu

Yue

Guo

. Grinding-aided electrochemical discharge machining of particulate reinforced metal matrix composites. Int J Adv Manuf Technol 2013; 68: 2349–2357.

15.

Venkatesh

Arun

Venkatesan

. Optimization of micro drilling parameters of B₄C DRMM Al 6063 composite in µECM using Taguchi coupled Fuzzy Logic. Procedia Eng 2014; 97: 975–985.

16.

Rao

Padmanabhan

Mahesh Naidu

et al.

Parametric study for radial over cut in electrochemical drilling of Al-5%B₄C_p composites. Procedia Eng 2014; 97: 1004–1011.

17.

Winkelmann

Lang

. Influence of the electrode distance and metal ion concentration on the resulting structure in electrochemical micromachining with structured counter electrodes. Int J Mach Tools Manuf 2013; 72: 25–31.

18.

Bhattacharyya

Malapati

Munda

et al.

Influence of tool vibration on machining performance in electrochemical micro-machining of copper. Int J Mach Tools Manuf 2007; 47: 335–342.