NiCr–Cr3C2 coatings are widely used for high temperature and tribological applications due to their high hardness, oxidation, and wear resistance properties. In the present investigation, an attempt is made to further enhance the hardness and adhesion strength of NiCr–Cr3C2 coatings by reinforcing them with multi-walled carbon nanotubes. The carbon nanotubes (3–7 wt%) with varying weight percentages were mixed with NiCr–Cr3C2 using a planetary ball rolling mill and sprayed on SA213 T12 (T12 alloy steel tube) using a high-velocity oxy-fuel spraying process. The microstructures of mixed powder, coating cross-section, and fractured coating surface were characterized using a scanning electron microscope while X-ray diffraction was used for phase identification in the fractured coating surface. The coated samples were subjected to microhardness and adhesion strength tests according to ASTM E384 and ASTM D4541-09 standards. Out of all coatings, NiCr–Cr3C2/7% carbon nanotube composite coating showed the lowest porosity of 1.17%, highest microhardness, and adhesion strength of 563.8 HV and 55.8 MPa, respectively. A fracture analysis after a pull-off adhesion test revealed adhesion failure for NiCr–Cr3C2 coating and combined adhesion/cohesion failure for NiCr–Cr3C2/7% carbon nanotube composite coating.
FrenchDN. Failures of boilers and related equipment. In: Failure analysis and prevention (eds. BeckerWTShipleyRJ), 2002, pp. 2604–2654. USA: ASM International, Materials Park, OH 44073-0002. DOI: 10.31399/asm.hb.v11.9781627081801.
2.
RickerbyDSWinstoneMRCoatings for gas turbines. Mater Manuf Process1992; 7: 495–526.
3.
SidhuTSPrakashSAgrawalRD. State of the art of HVOF coating investigations a review. Mar Technol Soc J2005; 39: 53–64.
4.
YilbasBS. HVOF coating of nickel based alloys: Surface and mechanical characteristics. In: Comprehensive Materials Finishing (ed. MSJ Hashmi), 2017, pp. 96–110. UK: Elsevier, Oxford, DOI: 10.1016/B978-0-12-803581-8.09170-0.
5.
ThiyagarajanBSenthilkumarV. Experimental studies on fly-ash erosion behavior of Ni–Cr based nanostructured thermal spray coating in boiler tubes. Mater Manuf Process2017; 32: 1209–1217.
6.
AngASMHowseHWadeSA,et al.Manufacturing of nickel based cermet coatings by the HVOF process. Surf Eng2016; 32: 713–724.
7.
KarbasiMGhavidelMRZSaidiA,et al.Comparison between tribological behaviour of HVOF coatings produced from conventional Ni + TiC powder mixture and Ni–TiC, Ni–(Ti,W)C composite powders. Surf Eng2012; 28: 155–163.
8.
ReddyNCKumarBSARameshMR,et al.Microstructure and adhesion strength of Ni3Ti coating prepared by mechanical alloying and HVOF. Phys Met Metallogr2018; 119: 462–468.
9.
ReddyNCKoppadPGReddappaHN,et al.Hot corrosion behaviour of HVOF sprayed Ni3Ti and Ni3Ti + (Cr3C2 + 20NiCr) coatings in presence of Na2SO4–40%V2O5 at 650°C. Surf Topogr Metrol Prop2019; 7: 025019.
10.
VerdianMM. Characterization and corrosion performance of HVOF sprayed Ni–10 wt% Ti coatings. Surf Eng2014; 30: 670–674.
11.
ShivalingaiahKSridharKSSethuramD,et al.HVOF sprayed Inconel 718/cubic boron nitride composite coatings: microstructure, microhardness and slurry erosive behaviour. Mater Res Exp2019; 6: 1265i8.
12.
BhosaleDGRathodWS. Tribo-behaviour of APS and HVOF sprayed WC–Cr3C2–Ni coatings for gears. Surf Eng2021; 37: 80–90.
13.
DingYHussainTMcCartneyDG. High-temperature oxidation of HVOF thermally sprayed NiCr–Cr3C2 coatings: microstructure and kinetics. J Mater Sci2015; 50: 6808–6821.
14.
YinBLiuGZhouH,et al.Sliding wear behavior of HVOF-sprayed Cr3C2–NiCr/CeO2 composite coatings at elevated temperature up to 800°C. Tribol Lett2010; 37: 463–475.
NagabhushanaNRajannaSMathapatiM,et al.Microstructure and tribological characteristics of APS sprayed NiCrBSi/Flyash cenosphere/Cr2O3 and NiCrBSi/Flyash cenosphere/Mo composite coatings at elevated temperatures. Mater Res Exp2019; 6: 086451.
19.
ShenderovaOAZhirnovVVBrennerDW. Carbon nanostructures. Crit Rev Solid State Mater Sci2002; 27: 227–356.
KoppadPGSinghVKRameshCSKoppadRGKashyapKT. Metal matrix nanocomposites reinforced with carbon nanotubes. In: Advanced carbon materials and technology (eds A Tiwari and SK Shukla), 2014, pp. 331–376. Hoboken: John Wiley & Sons, Inc., DOI: 10.1002/9781118895399.
22.
RaoR, et al.Carbon nanotubes and related nanomaterials: critical advances and challenges for synthesis toward mainstream commercial applications. ACS Nano2018; 12: 11756–11784.
23.
MallikarjunaHMSiddarajuCKumarHSS,et al.Nanohardness and wear behavior of copper–SiC–CNTs nanocomposites. FME Trans2020; 48: 688–692.
24.
SethuramDKeshavamurthyRPaljorS,et al.Effect of multiple reinforcements (CNT/Si3N4) on hardness, electrical conductivity and friction coefficient of aluminium hybrid composites. J Phys Conf Ser2020; 1455: 012011.
25.
GoyalKSinghHBhatiaR. Experimental investigations of carbon nanotubes reinforcement on properties of ceramic-based composite coating. J Aust Ceram Soc2019; 55: 315–322.
DeesomDCharoenrutKMoonngamS,et al.Fabrication and properties of NiCr/CNTs nanocomposite coatings prepared by high velocity oxy-fuel spraying. Surf Coat Technol2016; 306: 240–244.
28.
ThakurLAroraN. An investigation on the development and wear performance of chromium-MWCNTs transformed HVOF sprayed nano-WC–CoCr coatings. Surf Coat Technol2020; 388: 125610.
29.
KumarSBhatiaRSinghH. High-temperature corrosion behaviour of CNT-reinforced zirconium yttrium coatings on boiler tube steel in coal-fired boiler of thermal power plant. J Fail Anal Preven2020; 20: 2029–2039.
30.
KoppadPGKashyapKTShrathinthV,et al.Microstructure and microhardness of carbon nanotube reinforced copper nanocomposites. Mater Sci Technol2013; 29: 605–609.
31.
ManjunathaKGiridharaGJegadeeswaranN. Effect of carbon nanotube (CNT) additions in Cr3C2–25% NiCr coatings on microstructural and mechanical properties. Mater Today Proc2021; 45: 15–20.
32.
Uriza-VegaECarreno-GallardoCLopez-MelendezC, et al.Mechanical behavior of multiwalled carbon nanotube reinforced 7075 aluminum alloy composites prepared by mechanical milling and hot extrusion. Mater Res2019; 22: e20180652.
33.
KeshriAKBalaniKBakshiSR,et al.Structural transformations in carbon nanotubes during thermal spray processing. Surf Coat Technol2009; 203: 2193–2201.
34.
PoirierDLegouxJLimaRS. Engineering HVOF-sprayed Cr3C2–NiCr coatings: the effect of particle morphology and spraying parameters on the microstructure, properties, and high temperature wear performance. J Therm Spray Technol2013; 22: 280–289.
GoyalKSinghHBhatiaR. Hot corrosion behaviour of CNTs reinforced Cr2O3 composite coatings at elevated temperature. Mater Res Express2018; 5: 7347–7358. DOI: 10.1007/s11665-019-04482-5.
38.
KangKPakHKimJLeeC. Role of spray processes on microstructural evolution, and physical and mechanical properties of multi-walled carbon nanotube reinforced cu composite coatings. Appl Surf Sci2015; 356: 1039–1051. DOI: 10.1016/j.apsusc.2015.08.158.
39.
MasoumiHSafaviSMSalehiM.NahviSM. Effect of grinding on the residual stress and adhesion strength of HVOF thermally sprayed WC–10Co–4Cr coating. Mater Manuf Process2014; 29: 1139–1151. DOI: 10.1080/10426914.2014.930893.
40.
JambagiSCBandyopadhyayPP. Improvement in tribological properties of plasma-sprayed alumina coating upon carbon nanotube reinforcement. J Mater Eng Perform2019; 28 (12): 7347–7358. DOI: 10.1007/s11665-019-04482-5.
41.
HongSWuYWangQYingGLiGGaoWWangBGuoW. Microstructure and cavitation-silt erosion behavior of high-velocity oxygen-fuel (HVOF) sprayed Cr3C2-NiCr coating. Surf Coat Technol2013; 225: 85–91. DOI: 10.1016/j.surfcoat.2013.03.020.10.1016/j.surfcoat.2013.03.020.
