The premixed prevaporized engine operation method was used to study the effects of main combustion thermodynamic properties and residence time on soot formation in a spark-ignition engine. Select cases were repeated under early-injection, nearly homogeneous, spark-ignition direct-injection operation to determine if the impact of the investigated parameters was the same or if the impact of in-cylinder liquid fuel injection and the resulting heterogeneous fuel-air mixture alters the trends. The original premixed prevaporized study hypothesized that soot is more likely to form after main combustion than during the main combustion event under completely homogeneous conditions. This hypothesis was tested in this study by performing premixed prevaporized combustion phasing sweeps at equivalence ratios (Φs) of 1.35 and 1.40. Both sweeps showed low sensitivity of the particle size distribution to significant changes in peak temperature and pressure during combustion, providing supporting evidence for the original hypothesis. This information was then used to design experiments to isolate the impacts of pressure (engine load) and residence time (engine speed). A premixed prevaporized load sweep showed that particulate emissions increase as a function of load/pressure. A spark-ignition direct-injection load variation showed similar pressure dependence for cases with in-homogeneous in-cylinder fuel-air distributions. A premixed prevaporized residence time variation (performed by changing engine speed) demonstrated an increase in soot formation with increased residence time. The results for identical spark-ignition direct-injection residence-time variations suggest a trade-off in soot formation between the effects of increased mixing time and increased residence time for spark-ignition direct-injection operation. The premixed prevaporized load and speed points were each investigated using Φ sweeps to determine the critical enrichment threshold for soot formation (ΦC) and the dependence of soot formation for Φ > ΦC. The spark-ignition direct-injection investigations were performed at Φ = 0.98, such that any soot formation above the non-fuel-related baseline particle size distribution could be attributed either to mixture heterogeneity or in-cylinder fuel films.
ChanTWMelocheEKubshJRosenblattDBreznyRRideoutG. Evaluation of a gasoline particulate filter to reduce particle emissions from a gasoline direct injection vehicle. SAE Int J Fuels Lubr2012; 5(3): 1277–1290.
2.
MaikawaCLZimmermanNRaisKShahMHawleyBPantP, et al. Murine precision-cut lung slices exhibit acute responses following exposure to gasoline direct injection engine emissions. Sci Total Environ2016; 568: 1102–1109.
3.
KittelsonDKraftM. Particle formation and models. Hoboken, NJ: Wiley, 2014.
4.
AikawaKJetterJJ. Impact of gasoline composition on particulate matter emissions from a direct-injection gasoline engine: applicability of the particulate matter index. Int J Engine Res2014; 15(3): 298–306.
5.
DavisSCWilliamsSEBoundyRGMooreSA. 2016 vehicle technologies market report. Technical Report, Oak Ridge National Laboratory (ORNL), Oak Ridge, TN, 25May2017.
6.
HarrisSJMaricqMM. Signature size distributions for diesel and gasoline engine exhaust particulate matter. J Aerosol Sci2001; 32(6): 749–764.
7.
BaroneTLStoreyJMEYoungquistADSzybistJP. An analysis of direct-injection spark-ignition (DISI) soot morphology. Atmos Environ2012; 49: 268–274.
8.
DemuynckJFavreCBosteelsDHamjeHAnderssonJ. Real-world emissions measurements of a gasoline direct injection vehicle without and with a gasoline particulate filter. SAE technical paper 2017-01-0985, 2017.
OberdörsterG. Pulmonary effects of inhaled ultrafine particles. Int Arch Occup Environ Health2001; 74(1): 1–8.
11.
OberdörsterGUtellMJ. Ultrafine particles in the urban air: to the respiratory tract–and beyond?Environ Health Perspect2002; 110(8): A440–A441.
12.
Ibald-MulliAWichmannHEKreylingWPetersA. Epidemiological evidence on health effects of ultrafine particles. J Aerosol Med2002; 15(2): 189–201.
13.
PetersAWichmannHETuchTHeinrichJHeyderJ. Respiratory effects are associated with the number of ultrafine particles. Am J Respir Crit Care Med1997; 155(4): 1376–1383.
14.
Benbrahim-TallaaLBaanRAGrosseYLauby-SecretanBEl GhissassiFBouvardV, et al. Carcinogenicity of diesel-engine and gasoline-engine exhausts and some nitroarenes. Lancet Oncol2012; 13(7): 663–664.
15.
HeXRatcliffMAZiglerBT. Effects of gasoline direct injection engine operating parameters on particle number emissions. Energ Fuel2012; 26(4): 2014–2027.
16.
PiockWHoffmannGBerndorferASalemiPFusshoellerB. Strategies towards meeting future particulate matter emission requirements in homogeneous gasoline direct injection engines. SAE Int J Engines2011; 4(1): 1455–1468.
17.
SakaiSHagemanMRothamerDA. Effect of equivalence ratio on the particulate emissions from a spark-ignited, direct-injected gasoline engine. SAE technical paper 2013-01-1560, 2013.
18.
FarronCMatthiasNFosterDAndrieMKriegerRNajtP, et al. Particulate characteristics for varying engine operation in a gasoline spark ignited, direct injection engine. SAE technical paper 2011-01-1220, 2011.
19.
KayesDHochgrebS. Mechanisms of particulate matter formation in spark-ignition engines. 2. Effect of fuel, oil, and catalyst parameters. Environ Sci Technol1999; 33(22): 3968–3977.
20.
MaricqMMPodsiadlikDHBrehobDDHaghgooieM. Particulate emissions from a direct-injection spark-ignition (DISI) engine. SAE technical paper 1999-01-1530, 1999.
21.
PricePTwineyBStoneRKarKWalmsleyH. Particulate and hydrocarbon emissions from a spray guided direct injection spark ignition engine with oxygenate fuel blends. SAE technical paper 2007-01-0472, 2007.
22.
WangBMosbachSSchmutzhardSShuaiSHuangYKraftM. Modelling soot formation from wall films in a gasoline direct injection engine using a detailed population balance model. Appl Energ2016; 163: 154–166.
23.
PillaG. Investigation of particle formation processes in a GDI engine in catalyst heating operation. In: Proceedings of the SIA international conference—the spark ignition engine of the future, Strasbourg, 30 November – 1 December 2011. Société des Ingénieurs de l’Automobile (SIA).
24.
HagemanMDSakaiSSRothamerDA. Determination of soot onset and background particulate levels in a spark-ignition engine. Proc Combust Inst2015; 35(3): 2949–2956.
25.
LeachFStoneRRichardsonDLewisAAkehurstSTurnerJ, et al. Particulate emissions from a highly boosted gasoline direct injection engine. Int J Engine Res2018; 19(3): 347–359.
26.
TanakaDUchidaRNodaTKolbeckAHenkelSHardalupasY, et al. Effects of fuel properties associated with in-cylinder behavior on particulate number from a direct injection gasoline engine. SAE technical paper 2017-01-1002, 2017.
27.
BonatestaFChiappettaELa RoccaA. Part-load particulate matter from a GDI engine and the connection with combustion characteristics. Appl Energ2014; 124: 366–376.
28.
AikawaKSakuraiTJetterJJ. Development of a predictive model for gasoline vehicle particulate matter emissions. SAE technical paper 2010-01-2115, 2010.
29.
BönigMFeldermannCJanderHLüersBRudolphGWagnerH. Soot formation in premixed C2H4 flat flames at elevated pressure. Symp Int Combust1991; 23(1): 1581–1587.
30.
MaussFBockhornH. Soot formation in premixed hydrocarbon flames: prediction of temperature and pressure dependence. Zeitschr Physikal Chem1995; 188(1–2): 45–60.
31.
GlassmanI. Soot formation in combustion processes. Symp Int Combust1989; 22(1): 295–311.
32.
GuCLinHCamachoJLinBShaoCLiR, et al. Particle size distribution of nascent soot in lightly and heavily sooting premixed ethylene flames. Combust Flame2016; 165: 177–187.
33.
CommodoMDe FalcoGMinutoloPD’AnnaA. Structure and size of soot nanoparticles in laminar premixed flames at different equivalence ratios. Fuel2018; 216: 456–462.
34.
DesgrouxPFaccinettoAMercierXMoutonTKarkarDAEl BakaliA. Comparative study of the soot formation process in a “nucleation” and a “sooting” low pressure premixed methane flame. Combust Flame2017; 184: 153–166.
35.
GhiassiHJaramilloICLightyJS. Kinetics of soot oxidation by molecular oxygen in a premixed flame. Energ Fuel2016; 30(4): 3463–3472.
WangH. Formation of nascent soot and other condensed-phase materials in flames. Proc Combust Inst2011; 33: 41–67.
38.
CiajoloAD’AnnaABarbellaRTregrossiAVioliA. The effect of temperature on soot inception in premixed ethylene flames. Symp Int Combust1996; 26(2): 2327–2333.
39.
ZhaoBYangZLiZJohnstonMVWangH. Particle size distribution function of incipient soot in laminar premixed ethylene flames: effect of flame temperature. Proc Combust Inst2005; 30(1): 1441–1448.
GlassmanI. Sooting laminar diffusion flames: effect of dilution, additives, pressure, and microgravity. Symp Int Combust1998; 27(1): 1589–1596.
42.
RadcliffeSWAppletonJP. Shock-tube measurements of carbon to oxygen atom ratios for incipient soot formation with C2H2, C2H4 AND C4H6 fuels. Combust Sci Technol1971; 3(6): 255–262.
43.
BöhmHHesseDJanderHLüersBPietscherJWagnerHGGWeissM. The influence of pressure and temperature on soot formation in premixed flames. Symp Int Combust1989; 22(1): 403–411.
44.
McCrainLLRobertsWL. Measurements of the soot volume field in laminar diffusion flames at elevated pressures. Combust Flame2005; 140(1–2): 60–69.
45.
ThomsonKAGülderÖLWeckmanEJFraserRASmallwoodGJSnellingDR. Soot concentration and temperature measurements in co-annular, nonpremixed CH4/air laminar flames at pressures up to 4 MPa. Combust Flame2005; 140(3): 222–232.
46.
FlowerWLBowmanCT. Soot production in axisymmetric laminar diffusion flames at pressures from one to ten atmospheres. Proc Combust Inst1988; 21(1): 1115–1124.
47.
MandatoriPMGülderÖL. Soot formation in laminar ethane diffusion flames at pressures from 0.2 to 3.3 MPa. Proc Combust Inst2011; 33(1): 577–584.
48.
BentoDSThomsonKAGülderÖL. Soot formation and temperature field structure in laminar propane–air diffusion flames at elevated pressures. Combust Flame2006; 145(4): 765–778.
49.
HanischSJanderHPapeTWagnerH. Soot mass growth and coagulation of soot particles in C2H4/air-flames at 15 bar. Symp Int Combust1994; 25(1): 577–584.
50.
RoySPHaworthDC. A systematic comparison of detailed soot models and gas-phase chemical mechanisms in laminar premixed flames. Combust Sci Technol2016; 188(7): 1021–1053.
51.
HarrisMMKingGBLaurendeauNM. Influence of temperature and hydroxyl concentration on incipient soot formation in premixed flames. Combust Flame1986; 64(1): 99–112.
GhandhiJB. Pressure and heat release analysis. In: David Crolla (ed.) Encyclopedia of automotive engineering. 2014. Wiley.
54.
SalazarVM. Unburned hydrocarbon emission mechanisms in small engines. PhD Thesis, University of Wisconsin–Madison, Madison, WI, 2008.
55.
HagemanMD. Isolation of fundamental parameters contributing to particulate formation in a spark ignition direct injection (SIDI) engine. PhD Thesis, University of Wisconsin–Madison, Madison, WI, 2014.
56.
SakaiSRothamerD. Effect of ethanol blending on particulate formation from premixed combustion in spark-ignition engines. Fuel2017; 196: 154–168.
57.
ViswanathanSRothamerDAFosterDEFanslerTDZelenyukAStewartMLBellDM. Evolution of deep-bed filtration of engine exhaust particulates with trapped mass. Int J Engine Res2016; 18: 543–559.
58.
YilmazETianTWongVWHeywoodJB. The contribution of different oil consumption sources to total oil consumption in a spark ignition engine. SAE technical paper 2004-01-2909, 2004.
59.
OhCChengWK. Assessment of gasoline direct injection engine cold start particulate emission sources. SAE Int J Engines2017; 10: 1556–1565.
60.
BöhmHFeldermannCHeidermannTJanderHLüersBWagnerH. Soot formation in premixed C2H4-air flames for pressures up to 100 bar. Symp Int Combust1992; 24(1): 991–998.
61.
KayesDHochgrebS. Mechanism of particulate matter formation in spark-ignition engines. 3. Model of PM formation. Environ Sci Technol1999; 33(22): 3978–3992.
62.
MätzingHWagnerHG. Measurements about the influence of pressure on carbon formation in premixed laminar C2H4-air flames. Symp Int Combust1988; 21(1): 1047–1055.
63.
RothamerDAGhandhiJB. Determination of flame-front equivalence ratio during stratified combustion. SAE technical paper 2003-01-0069, 2003.
64.
NoyoriT. Experimental study of smoke emission on small-displacement spark-ignition direct-injection engine. SAE technical paper 2006-32-0105, 2006.
