Influence of tumble and TKE on combustion,fuel economy,and emissions of a single cylinder motorcycle engine

Abstract

The impact of gasoline engines on improving fuel consumption and reducing emissions has received increasing attention around the world, and emissions regulations have become stricter. However, complex techniques in engine improvement increase costs. The purpose of this study is to develop or improve the design of the intake geometry without additional cost to improve the engine thermal efficiency, thereby improving fuel economy and emissions. In this study, emissions and fuel consumption of a 125 c.c. commercially available motorcycle was investigated. In addition to modifying the intake and valve angles and maintaining the intake air volume, a software for computational fluid dynamics (CFD) was used for steady-state and transient analysis of the in-cylinder flow field, tumble ratio and turbulence kinetic energy (TKE), and the results were compared with the data of the experimental platform. The burn duration of the engine, indicated mean effective pressure (IMEP), indicated specific total hydrocarbons (ISHC), nitrogen oxide (ISNO_x) and carbon monoxide (ISCO) were measured on the bench. The transient predicted results show that the tumble ratio is a maximum increase of 27.82% at 656 crank angle (CA) degrees near the top dead center (TDC) on the compression stroke. In the ignition area within 5°–20° before top dead center (BTDC), average of the turbulence kinetic energy (TKE) was 120.37 m²/s², distributed hot area was wide and close to the ignition position. In the steady-state measurement, it was verified that the tumble ratio was significantly improved by modifying inlet, the same trend as the analysis result. In the bench test for full load measurement, the average of IMEP increased by 10.92%, indicated specific fuel consumption (ISFC) improved by 11.7%, burn duration increased by 25.27%, ISCO improved by 43.41%, and ISHC improved by 64.33%. For portion load measurement, the average of ISFC improved by 2.16%, burn duration increased by 24.84%, ISCO improved by 43.44%, ISHC improved by 17.7% and ISNO improved by 12.89%. Based on the results, the tumble and TKE were improved by optimizing the angle between the intake valve and the intake port. The ISFC of model B was significantly improved under the two states. The ignition delay time was longer, and the overall burn duration was much improved. When it came to emissions, the ISCO and ISHC were significantly improved, and the ISNO was much higher at full load but lower at partial load due to the engine temperature and engine loads. At partial loads, the high tumble did benefit the combustion, fuel economy and emissions of a single-cylinder motorcycle engine.

Keywords

Tumble TKE combustion motorcycle fuel economy emissions

Get full access to this article

View all access options for this article.

References

Schögl

Edtmayer

Schmidt

, et al. Design of a tumble-orientated intake port layout for a gasoline combustion process used in power sport application. SAE paper 2011-32-0589, 2011.

Floch

Van Frank

Ahmed

. Comparison of the effects of intake-generated swirl and tumble on turbulence characteristics in a 4-valve engine. SAE paper 952457, 1995.

Lee

Bae

Kang

. The effects of tumble and swirl flows on flame propagation in a four-valve S.I. Engine. Appl Therm Eng 2007; 27: 2122–2130.

Urushihara

Murayama

Takagi

, et al. Turbulence and cycle-by-cycle variation of mean velocity generated by swirl and tumble flow and their effects on combustion. SAE paper 950813, 1995.

Zhao

Freeland

Hawley

Xia

. Numerical analysis of a downsized 2-stroke uniflow engine. SAE Int J Engines 2014; 7: 2035–2044.

Zhao

. The modeling and design of a boosted uniflow scavenged direct injection gasoline (BUSDIG) engine. SAE paper 2015-01-1970, 2015.

Masi

Artico

Gobbato

. Measurements of the intake and in-cylinder flow field to investigate the reliability of CFD steady-state simulations for actual engines. SAE paper 2015-24-2404, 2015.

Hoag

Megel

. Methodology development for tumble port evaluation. SAE paper 2016-01-0636, 2016.

Abidin

Hoag

Mckee

, et al. Port design for charge motion improvement within the cylinder. SAE paper 2016-01-0600, 2016.

10.

Cameretti

De Bellis

Romagnuolo

, et al. 3D CFD analyses of intake duct geometry impact on tumble motion and turbulence production in SI engines. SAE paper 2017-01-2199, 2017.

11.

Iyer

. 3D CFD upfront optimization of the in-cylinder flow of the 3.5L V6 ecoboost engine. SAE paper 2009-01-1492, 2009.

12.

Yoshihara

Nakata

Takahashi

, et al. Development of high tumble intake-port for high thermal efficiency engines. SAE paper 2016-01-0692, 2016.

13.

Omura

Nakata

Yoshihara

, et al. Research on the measures for improving cycle-to-cycle variations under high tumble combustion. SAE paper 2016-01-0694, 2016.

14.

Ogink

Babajimopoulos

. Investigating the limits of charge motion and combustion duration in a high-tumble spark-ignited direct-injection engine. SAE Int J Engines 2016; 9: 2129–2141.

15.

Zhang

Wang

Jia

. Effects of tumble combined with EGR (exhaust gas recirculation) on the combustion and emissions in a spark ignition engine at part loads. Energy 2014; 65(1): 18–24.

16.

Bari

Saad

. CFD modelling of the effect of guide vane swirl and tumble device to generate better in-cylinder air flow in a CI engine fuelled by biodiesel. Comput Fluids 2013; 84: 262–269.

17.

Kim

Yan

Nouri

Arcoumanis

. Effects of intake flow and coolant temperature on the spatial fuel distribution in a direct-injection gasoline engine by PLIF technique. Fuel 2013; 106: 737–748.

18.

Brusiani

Falfari

Cazzoli

. Tumble motion generation in small gasoline engines: a new methodological approach for the analysis of the influence of the intake duct geometrical parameters. Energy Proc 2014; 45: 997–1006.

19.

Changming

Sichuan

. The investigation and application of variable tumble intake system on a GDI engine. SAE Int J Engines 2014; 7(4): 2022–2034.

20.

Sureshkumar

GANESAN

Mallikarjuna

, et al. Effect of piston crown shape on in-cylinder flow characteristics in a direct injection engine – a CFD study. SAE paper 2013-01-2797, 2013.

21.

Buhl

Gleiss

Köhler

, et al. A combined numerical and experimental study of the 3D tumble structure and piston boundary layer development during the intake stroke of a gasoline engine. Flow Turbul Combust 2017; 98: 579–600.

22.

Baratta

Misul

Spessa

Viglione

Carpegna

Perna

. Experimental and numerical approaches for the quantification of tumble intensity in high-performance SI engines. Energy Convers Manag 2017; 138: 435–451.

23.

ANSYS Inc. Internal combustion engine in workbench, www.ansys.com (2018, accessed 26 December 2018).

24.

Stone

Ladommatos

. The measurement and analysis of swirl in steady flow. SAE paper 1992; 921642.

25.

Heywood

. Internal Combustion Engine Fundamentals. New York: McGraw Hill, 1988.

26.

Ganesan

. Internal Combustion Engines. 2nd ed. New Delhi: Tata McGraw-Hill, 2003.

27.

Gómez Montoya

Amell Arrieta

. Effect of the turbulence intensity on knocking tendency in a SI engine with high compression ratio using biogas and blends with natural gas, propane and hydrogen. Int J Hydrogen Energy 2019; 44: 18532–18544.

28.

Lee

. Effects of tumble and swirl flows on turbulence scale near top dead centre in a four-valve spark ignition engine. Proc IMechE, Part D: J Automobile Engineering 2003; 217: 607–615.