Structural Health Monitoring of a Metallic Sandwich Panel by the Method of Virtual Forces

Abstract

A structural health monitoring system for assessing thermal damage in a metallic sandwich panel was developed in this article. The method of virtual forces was utilized to detect, locate, and quantify damage. The method assumes that a damaged structural response is a summation of the undamaged response and the response from an effective forcing function, which represents the effects of the material damage. The effective forcing function, or virtual force, is an estimate of the forces that the damage mechanism exerts on the undamaged structure. Virtual forces were shown to detect changes in the mass, stiffness, and damping matrices in a lumped parameter dynamic model. A finite element model of a mechanically attached sandwich metallic panel was used to detect a stiffness loss at different locations between two sensor locations. These results were then compared with experimental results involving thermal debond between the face sheet and core of an Al—Al honeycomb panel. Virtual forces indicated there was damage associated with magnitude and frequency shifts in the frequency response function measurements made on the damaged panel. Damage was located relative to the sensor/actuator measurement locations. Damage that was not adjacent to measurement locations was less accurately located and quantified. Variability in producing localized thermal debond using an acetylene torch was also apparent in the virtual force estimates. The virtual force estimates also indicated that damage was spread over several measurement locations because highly localized thermal debond was difficult to produce.

Keywords

structural health monitoring virtual force vibration based health monitoring thermal debond

Get full access to this article

View all access options for this article.

References

Freeman, D.C. and Talay, T.A. (1997). Reusable launch vehicle technology program. Acta Astronautica, 41(11), 777-779.

Samuel, P.D. and Pines, D.J. (2004). A review of vibration-based techniques for helicopter transmission diagnostics. Journal of Sound and Vibration, 282, 475-508.

Yang, J. and Chang, F. ( 2006). Detection of bolt loosening in C-C composite thermal protection panels: I. diagnostic principle. Smart Materials and Structures, 15, 581-590.

Giurgiutiu, V. (2005). Tuned lamb wave excitation and detection with piezoelectric wafer active sensors for structural health monitoring. Journal of Intelligent Material Systems and Structures , 16, 291-305.

Sundararaman, S. , Adams, D.E. and Rigas, E.J. (2005). Structural damage identification in homogenous and heterogeneous structures using beamforming. Structural Health Monitoring, 4(2), 171-190.

White, J.R. , Adams, D.E. and Jata, K. ( 2005). Modeling and material damage identification of a sandwich plate using MDOF modal parameter estimation and the method of virtual forces . In: ASME International Mechanical Engineering Congress and Exposition Proceedings, Orlando, FL.

White, J.R. , Adams, D.E. and Jata, K. ( 2006). Damage identification in a sandwich plate using the method of virtual force. In: International Modal Analysis Conference Proceedings, St. Louis, MO.

Tsuei, Y.G. and Yee, E.K.L. ( 1989). A method for modifying dynamic properties of undamped mechanical systems. Dynamic System Measurement Control, 111, 403-408.

Elwasia, N. , Sundaresan, M.J. , Schulz, M.J. , Ghoshal, A. , Pai, P.F. and Tu, P.K.C. ( 2006). Damage bounding structural health monitoring. Journal of Intelligent Material Systems and Structures, 17, 629-648.

10.

Hwang, H.Y. and Kim, C. (2004). Damage detection using a few frequency response measurements. Journal of Sound and Vibration, 270, 1-14.

11.

Kaouk, M. and Zimmerman, D.C. ( 1994). Structural damage assessment using a generalized minimum rank perturbation theory. AIAA Journal, 32(4), 836-842.

12.

Doebling, S.W. (1996). Minimum-rank optimal update of elemental stiffness parameters for structural damage identification. AIAA Journal, 34(12), 2615-2621.

13.

Escobar, J.A. , Sosa, J.J. and Gomez, R. (2005). Structural damage detection using the transformation matrix. Computers and Structures , 83, 357-368.