An investigation was performed to develop a sensor placement method to maximize the performance of a structural health monitoring (SHM) system with a minimal number of sensors for detection of impact in structures, particularly for structures made of fiber-reinforced composite materials. The performance of the SHM system is evaluated based on the probability of detection (POD). This optimization problem was formulated to maximize the POD through selection of optimal sensor locations for a given sensor network. A genetic algorithm was adopted and integrated with the SHM system to perform the optimization process. Numerical simulations on two composite panels showed that the selection of sensor network configuration is crucial for the performance of the SHM system. For a targeted POD, the proposed method can be used to configure an SHM system with a minimal number of sensors to identify impact forces that are greater than a pre-defined critical value.
Gunther, M.F. , Wang, A., Fogg, B.R., Starr, S.E., Murphy, K.A. and Claus, R.O. (1993). Fiber optic impact detection and location system embedded in a composite material. In: Smart Structures and Materials, Proceedings of the SPIE, Vol. 1798, pp. 262-269.
2.
Doyle, J.F. ( 1987). Experimentally determining the contact force during the transverse impact of an ortho-tropic plate. Journal of Sound and Vibration, 118, 441-448.
3.
Wu, E., Yeh, J.-C. and Yen, C.-S. ( 1994). Identification of impact forces at multiple locations on laminated plates. AIAA Journal, 32, 2433-2439.
4.
Seydel, R. and Chang, F.K. ( 2001). Impact identification of stiffened composite panelsI. system development, Smart Materials and Structures, 10, 354-369.
5.
Chandrashekara, K., Okafor, A.C. and Jiang, Y.P. (1996). Estimation of contact force on composite plates using impact induced strain and neural network. In: Smart Structures and Materials, Proceedings of the SPIE, Vol. 218, pp. 320-330.
6.
Akhavan, F., Watkins, S.E. and Chandrashekara, K. ( 1996). Recovery of impact contact forces of composite plates using fiber optic sensors and neural networks. In:Smart Structures and Materials, Proceedings of the SPIE, Vol. 2839, pp. 277-288.
7.
Jones, R.T., Sirkis, J.S. and Friebele, E.J. ( 1997). Detection of impact location and magnitude for isotropic plates using neural networks. Journal of Intelligent Material Systems and Structures, 7, 90-99.
8.
Saafi, M. and Romine, P. ( 2003). Health monitoring of concrete structures using embedded MEMS. In: Chang, F.K. (ed.), Proceedings of the 4th International Workshop on Structural Health Monitoring, Stanford University, pp. 952-959.
9.
Gordon, G., Atodaria, J. and Aaseng, G. ( 2005). Designing a structural health monitoring system for the NASA space shuttle. In: Chang, F.K. (ed.), Proceedings of the 5th International Workshop on Structural Health Monitoring, Stanford University, pp. 1659-1666.
10.
Boller, C. ( 2005). Process chain elements for health management of engineering structures. In: Chang, F.K. (ed.), Proceedings of the 5th International Workshop on Structural Health Monitoring, Stanford University, pp. 1463-1470.
11.
Speckmann, H. and Daniel, J. ( 2004). Structural health monitoring for airliner, from research to user requirements, a European view, airbus, Germany. In: AIAA-2004-6742, CANEUS Conference on Micro-nanotechnologies, Monterey, California.
12.
Schmidt, H. ( 2003). Damage tolerant design and analysis of current and future aircraft structures. In: AIAA-2003-2784, AIAA International Air and Space Symposium and Exposition: The Next 100 Years, Dayton, Ohio.
13.
MacConnel, J. (2005). ISHM and design: a new capability perspective. In: Chang, F.K. (ed.), Proceedings of the 5th International Workshop on Structural Health Monitoring, Stanford University, pp. 1293-1300.
14.
Derriso, M., Pratt, D., Homan, D., Schroeder, J. and Bortner, R. ( 2003). Integrated vehicle health management: the key to future aerospace systems. In: Chang, F.K. (ed.), Proceedings of the 4th International Workshop on Structural Health Monitoring, Stanford University, pp. 3-11.
15.
Cawley, P., Fromme, P., Wilcox, P. and Lowe, M. ( 2004). A guided wave array for structural health monitoring . In: 2nd European Workshop on Structural Health Monitoring, Munich, Germany, 2004.
16.
Kessler, S., Spearing, S., Atalla, M., Cesnik, C. and Soutis, C. ( 2001). Damage detection in composite materials using frequency response methods. In: The SPIE Symposium on Smart Structures and Materials, 7 March 2001, Newport Beach, CA.
17.
Staszewski, W. (1998). Structural and mechanical damage detection using wavelets. The Shock and Vibration Digest , 30, 457-472.
18.
Mal, A. , Ricci, F., Banerjee, S. and Shih, F. (2005). A conceptual structural health monitoring system based on vibration and wave propagation. Structural Health Monitoring: An International Journal, 4, 283-293.
19.
Chang, F.-K. and Park, J. ( 2003). Built-in detection of impact damage in multi-layered thick composite structures. In: Chang, F.-K. (ed.), Proceedings of the 4th International Workshop on Structural Health Monitoring, Stanford University , pp. 1391-1398.
20.
Wang, C., Wu, F. and Chang, F.-K. ( 2001). Structural health monitoring from fiber- reinforced composites to steel-reinforced concrete. Journal of Smart Materials and Structures, 10, 548-552.
21.
Beard, S. and Chang, F.-K. ( 1997). Active damage detection in filament wound composite tubes using built-in sensors and actuators. Journal of Intelligent Material System and Structures, 8, 891-897.
22.
Ihn, J.-B. and Chang, F.-K. ( 2004). Detection and monitoring of hidden fatigue crack growth using a built-in piezoelectric sensor/actuator network: Part I- diagnostics . In: Smart Materials and Structures, Proceedings of SPIE, pp. 609-620.
23.
Ihn, J.-B. and Chang, F.-K. (2004). Detection and monitoring of hidden fatigue crack growth using a built-in piezoelectric sensor/actuator network: Part II- validation through riveted joints and repair patches. In: Smart Materials and Structures, Proceedings of SPIE, Vol. 13, pp. 621-630.
24.
Fogg, B.R., Gunther, M.F. and Wang, A. ( 1993). Fiber optic impact detection and location system embedded in a composite material. In: Smart Materials and Structures, Proceedings of the SPIE, Vol. 1798, pp. 262-269.
25.
Yen, C.S. , Wu, E. and Yeh, J.C. (1994). Identification of impact forces at multiple locations on laminated plates. Journal of AIAA, 32, 2433-2439.
26.
Jiang, Y.P. , Chandrashekara, K. and Okafor, A.C. (2000). Estimation of contact force on composite plates using impact induced strain and neural network. In: Smart Materials and Structures, Proceedings of SPIE, Vol. 218, pp. 320-330.
27.
Chandrashekara, K., Akhavan, F. and Watkins, S.E. (2000). Recovery of impact contact forces of composite plates using fiber optic sensors and neural networks . In: Smart Materials and Structures, Proceedings of SPIE , Vol. 2839, pp. 277-288.
28.
Park, J. and Chang, F.-K. ( 2005). System identification method for monitoring impact events . In: Smart Structures and Materials: Modeling, Signal Processing, and Control, Proceedings of SPIE, Vol. 5758, pp. 189-200.
29.
Markmiller, J. and Chang, F.-K.Quantification of a passive sensing impact monitoring system. Journal of Smart Materials and Structures (submitted).
30.
Markmiller, J. and Chang, F.-K.A passive sensing impact detection system for composite structures: Model development. Journal of Smart Materials and Structures (submitted).
31.
Sheng, S., Gao, R.X. and Wang, C. ( 2004). Optimal sensor placement strategy and sensos design for high quality system monitoring, In: Smart Structures and Materials: Sensors and Smart Structures Technologies for Civil, Mechanical, and Aerospace Systems, Proceedings of SPIE, Vol. 5391, pp. 431-440.
32.
Zhang, L.L., Guo, H. and Zhang, L. ( 2004). Optimal placement of sensors for structural health monitoring using improved genetic algorithms. In: Smart Materials and Structures, Proceedings of SPIE, Vol. 13, pp. 528-534.
33.
Abdullah, M.M. and Richardson, A. (2002). Sensor/actuators placement on civil structure using a real coded genetic algorithm. Smart Structures and Materials, Proceedings of SPIE, Vol. 4696, pp. 244-255.
34.
Wardle, R., Staszewski, W.J. and Worden, K. ( 2000). Fail-safe sensor distributions for impact detection in composite materials. In: Smart Material and Structures, Proceedings of SPIE, Vol. 9, pp. 298-303.
35.
Burrows, A.P. and Worden, K. (2001). Optimal sensor placement for fault detection. Engineering Structures, 23(23), 885-890.
36.
Baker, J. ( 1987). Reducing bias and inefficiency in the selection algorithm . In: Grefenstette, J. (ed.), Genetic Algorithms and Their Applications: Proceedings of the 2nd International Conference of LEA, Cambridge, MA, pp. 14-21.
37.
K. DeJong , ‘‘Adaptive system design: a genetic approach,’’ IEEE Transactions on Systems, Man, and Cybernetics, SMC-10(9), 566-574.
38.
Holland, J. ( 1975). Adaptation in Natural and Artificial Systems, Ann Arbor: University of Michigan Press.
39.
Smith, S. ( 1983). Flexible learning of problem solving heuristics through adaptive search. In: Proceedings of the 8th International Joint Conference on Artificial Intelligence (IJCAI), Karlsruhe , Germany, 1983.
