The propagation properties of ultrasonic waves in rebar-reinforced concrete beams were investigated and their ability for damage identification was demonstrated. Rectangular piezoelectric ceramics were attached at the exposed ends of the rebar to monitor the wave transmission along the rebar with and without simulated corrosion, which was introduced in the form of partial removal of material from the rebar. Experimental testing demonstrated that the presence of concrete had a significant influence on the propagation characteristics of guided waves along the rebar. In consideration of the inevitable discrepancies in different concrete beams due to individual specimen preparation and sensor installation, the time-reversal process was applied to identify the damage. A damage index was defined based on the correlation coefficient between the actuated and the reconstructed wave signals. Wavelet transform was applied to overcome the wave conversion difficulty and to reduce the noise in the captured wave signals. Damage of different sizes was introduced and then was correlated with the damage index. Enlarging the damage size resulted in an increase in the level of distortion in the reconstructed wave signals, and consequently, a higher damage index was obtained. The results demonstrate the efficiency of the time-reversal process in identifying damage in rebar-reinforced concrete structures.
ParkGCudneyHHInmanDJ. Impedance-based health monitoring of civil structural components. J Infrastruct Syst2000; 6(4): 153–160.
4.
BonteaD-MChungDDLLeeGC. Damage in carbon fiber-reinforced concrete, monitored by electrical resistance measurement. Cement Concrete Res2000; 30(4): 651–659.
5.
SuZYeLLuY. Guided Lamb waves for identification of damage in composite structures: a review. J Sound Vib2006; 295(3–5): 753–780.
6.
SongFHuangGLKimJHHaranS. On the study of surface wave propagation in concrete structures using a piezoelectric actuator/sensor system. Smart Mater Struct2008; 17: 055024.
7.
SunMStaszewskiWJSwamyRNLiZ. Application of low-profile piezoceramic transducers for health monitoring of concrete structures. NDT&E Int2008; 41: 589–595.
8.
YangYCascanteGPolakaMA. Depth detection of surface-breaking cracks in concrete plates using fundamental Lamb modes. NDT&E Int2009; 42: 501–512.
9.
LinXYuanFG. Detection of multiple damages by prestack reverse-time migration. AIAA J2001; 39(11): 2206–2215.
10.
AndersonBEGuyerRAUlrichTJJohnsonPA. Time reversal of continuous-wave, steady-state signals in elastic media. Appl Phys Lett2009; 94: 111908-1–111908-3.
11.
LarmatCSGuyerRAJohnsonPA. Time-reversal methods in geophysics. Phys Today2010; 63: 31–35.
12.
SutinAMJohnsonPATenCateJ. Development of nonlinear time reversed acoustics (NLTRA) for applications to crack detection in solids. In: Proceedings of the World Congress on Acoustics, Paris, 7–10 September 2003, pp. 121–124. Société française d’acoustique.
13.
SutinAMTenCateJAJohnsonPA. Single-channel time reversal in elastic solids. J Acoust Soc Am2004; 116(5): 2779–2784.
14.
UlrichTJJohnsonPASutinA. Imaging nonlinear scatterers applying the time reversal mirror. J Acoust Soc Am2006; 119(3): 1514–1518.
15.
UlrichTJSutinAMGuyerRAJohnsonPA. Time reversal and non-linear elastic wave spectroscopy (TR NEWS) techniques. Int J Nonlin Mech2008; 43(3): 209–216.
16.
KimSBSohnH. Application of time-reversal guided waves to field bridge testing for baseline-free damage diagnosis. In: Proceedings of the SPIE: health monitoring and smart nondestructive evaluation of structural and biological systems V, San Diego, CA, 26 February 2006, vol. 617706, pp. 50–59. SPIE.
17.
SaengerEHKocurGKJudRTorrilhonM. Application of time reverse modeling on ultrasonic non-destructive testing of concrete. Appl Math Model2011; 35(2): 807–816.
18.
MillerTHKunduTHuangJGrillJY. A new guided wave-based technique for corrosion monitoring in reinforced concrete. Struct Health Monit2013; 12(1): 35–47.
19.
LuYLiJYeLWangD. Guided waves for damage detection in rebar-reinforced concrete beams. Constr Build Mater2013; 47: 370–378.
20.
ZhuXQHaoHFanKQ. Detection of delamination between steel bars and concrete using embedded piezoelectric actuators/sensors. J Civil Struct Health Monit2013; 3(2): 105–115.
21.
SohnHParkHWLawKHFarrarCR. Damage detection in composite plates by using an enhanced time reversal method. J Aerospace Eng2007; 20: 141–151.
22.
MustaphaSYeLWangDLuY. Debonding detection in composite sandwich structures based on guided waves. AIAA J2012; 50(8): 1697–1706.
23.
WangDYeLLuY. A probabilistic diagnostic algorithm for identification of multiple notches using digital damage fingerprints (DDFs). J Intel Mat Syst Str2009; 20(12): 1439–1450.
24.
WooPHBumKSSohnH. Understanding a time reversal process in Lamb wave propagation. Wave Motion2009; 46(7): 451–467.
25.
NaW-BKunduTEhsaniMR. Lamb waves for detecting delamination between steel bars and concrete. Comput-Aided Civ Inf2003; 18: 58–63.
26.
LuoQBungeyJH. Using compression wave ultrasonic transducers to measure the velocity of surface waves and hence determine dynamic modulus of elasticity for concrete. Constr Build Mate1996; 10(4): 237–242.
27.
WuFChangFC. Debond detection using embedded piezoelectric elements for reinforced concrete structures – part II: analysis and algorithm. Struct Health Monit2006; 5(1): 17–28.
28.
ErvinBLReisH. Longitudinal guided waves for monitoring corrosion in reinforced mortar. Meas Sci Technol2008; 19: 055702.
29.
PavlakovicBN. Leaky guided ultrasonic waves in NDT. PhD Thesis, Imperial College of Science, Technology and Medicine, University of London, London, 1998.
30.
BeardMDLoweMJSCawleyP. Ultrasonic guided waves for inspection of grouted tendons and bolts. J Mater Civil Eng2003; 15(3): 212–218.
31.
PavlakovicBNLoweMJSCawleyP. Prediction of reflection coefficients from defects in embedded bars. In: ThompsonDOChimentiDE (eds) Review of progress in quantitative NDE, vol. 18. New York: Plenum Press, 1999, pp. 207–214.
32.
WangYZhuXHaoHOuJ. Guided wave propagation and spectral element method for debonding damage assessment in RC structures. J Sound Vib2009; 324: 751–772.
33.
SharmaSMukherjeeA. Longitudinal guided waves for monitoring chloride corrosion in reinforcing bars in concrete. Struct Health Monit2010; 9(6): 555–567.
34.
LuYYeLSuZYangC. Quantitative assessment of through-thickness crack size based on Lamb wave scattering in aluminium plates. NDT&E Int2008; 41: 59–68.
35.
GangadharanRMurthyCRLGopalakrishnanSBhatMR. Time reversal technique for health monitoring of metallic structure using Lamb waves. Ultrasonics2009; 49(8): 696–705.
36.
StaszewskiWBollerCTomlinsonG. Health monitoring of aerospace structures: smart sensor technologies and signal processing. New York: Wiley, 2004.
37.
WangDYeLSuZLuYLiFMengG. Probabilistic damage identification based on correlation analysis using guided wave signals in aluminum plates. Struct Health Monit2010; 9(2): 133–144.
