Hygrothermal performance of internally insulated brick wall in cold climate: A case study in a historical school building

Abstract

Interior thermal insulation is frequently one of the only possible solutions for thermal upgrade of the building envelope where the external appearance cannot be changed. In this study, four insulation materials were used in a case study in a historical school building in in situ test walls. The indoor climate in the test room was controlled to simulate the typical dwelling with high moisture load. The temperatures, relative humidity, and heat flows were monitored over 9 months to analyze the hygrothermal performance of four different insulation materials. The hygrothermal performance of insulation materials during drying and wetting periods are presented. Moisture test reference year was used in working out possible energy-renovation solutions. The results show that timing of the renovation works is a matter of consideration to avoid the hygrothermal risks inside the renovated wall assemblies. The results show that in all the cases, thermal comfort can be improved by increasing the inner surface temperature and decreasing thermal conductivity. However, in some cases, the risks of mold growth and interstitial condensation were present inside the retrofitted wall assemblies. Computer simulations of the wall assemblies with moisture reference years under different humidity loads concluded that all solutions are suitable for future analysis.

Keywords

interior insulation hygrothermal performance historic building capillary active case study

Get full access to this article

View all access options for this article.

References

Grunewald

(1997) Diffusiver und konvektiver Stoff-und Energietransport in kapillarporösen Baustoffen. PhD Thesis, TU Dresden, Dresden.

Häupl

Fechner

Petzold

(2004) Interior retrofit of masonry wall to reduce energy and eliminate moisture damage: comparison of modeling and field performance. In: Proceedings of the thermal performance of the exterior envelopes of buildings IX, Clearwater Beach, FL, 5–10 December 2004.

Häupl

Jurk

Petzold

(2003) Inside thermal insulation for historical facades. In: Proceedings of the 2nd international conference on building physics, Antwerpen, 14–18 September, pp. 463–469. Antwerpen, Belgium: AA Balkema Publishers.

Hens

(1998) Performance predictions for masonry walls with inside insulation using calculation procedures and laboratory testing. Journal of Thermal Envelope and Building Science 22: 32–48.

Jürgenson

(1942) Elamu soojapidavus. Tartu: Tartu Eesti kirjastus, p. 203.

Kalamees

(2006) Indoor hygrothermal loads in Estonian dwellings. In: Proceedings of the 4th European conference on energy performance and indoor climate in buildings and the 27th conference of the Air Infiltration and Ventilation Centre, Lyon, 20–22 November, pp. 541–546. Lyon, France: Air Infiltration and Ventilation Centre.

Kalamees

Vinha

(2004) Estonian climate analysis for selecting moisture reference years for hygrothermal calculations. Journal of Thermal Envelope and Building Science 27(3): 199–220.

Künzel

(2011) Bauphysik der Innendämmung und Bewertungsverfahren. In: Proceedings of the 1. Internationaler Innendämmkongress, Dresden, 20–21 May, pp. 9–16. Dresden: TU Dresden.

Kuts

Sheiman

(1965) Investigation of the hygroscopic properties of peat insulating slabs. Journal of Engineering Physics 9(5): 394–396.

10.

Maurenbrecher

AHP

Shirtliffe

Rousseau

. (1998) Monitoring the hygrothermal performance of a masonry wall with and without thermal insulation on its interior surface. In: Proceedings of the 8th Canadian masonry symposium, Jasper, AB, Canada, 31 May–3 June.

11.

Mikk

(1977) Soojustehnika käsiraamat. Tallinn: Valgus, p. 85.

12.

Morelli

Scheffler

Nielsen

. (2010) Internal insulation of masonry walls with wooden floor beams in northern humid climate. In: Proceedings of thermal performance of the exterior envelopes of whole buildings XI (U.S. Department of Energy, Oak Ridge National Laboratory), Clearwater Beach, FL, 5–9 December, pp. 89–100. Atlanta, GA: ASHRAE.

13.

Nicolai

Scheffler

Grunewald

. (2008) An efficient numerical solution method and implementation for coupled heat, moisture and salt transport: The Delphin program, (Research Report on Priority Program DFG SPP 1122) (ed Franke

Dekkelmann

Espinosa-Marzal

). Göttingen: Cuilliver Verlag, pp. 85–100.

14.

Nielsen

Möller

Rasmussen

. (2012) Use of sensitivity analysis to evaluate hygrothermal conditions in solid brick walls with interior insulation. In: Proceedings of the 5th international building physics conference (IBPC)—NSB 2011, Kyoto, Japan, 28–31 May, vol. 1, pp. 377–384. Japan: Department of Architecture and Architectural Engineering of Kyoto University.

15.

Scheffler

Grunewald

(2003) Material development and optimisation supported by numerical simulation for capillary-active inside insulation material. In: Proceedings of the 2nd international conference on building physics, Antwerpen, 14–18 September, pp. 77–85. Antwerpen, Belgium: AA Balkema Publishers.

16.

Scheffler

(2011) Hygric performance of internal insulation with light-weight autoclaved aerated concrete. In: Proceedings of 5th International Conference on Autoclaved Aerated Concrete, Bydgoszcz, 15–16 September, pp. 323–335.

17.

Stopp

Strangeld

Fechner

. (2001) The hygrothermal performance of external walls with inside insulation. In: Proceedings of the thermal performance of the exterior envelopes of buildings VIII, Clearwater Beach, FL, 2–7 December.

18.

Toman

Vimmrová

Černý

(2009) Long-term on-site assessment of hygrothermal performance of interior thermal insulation system without water vapour barrier. Energy and Buildings 41(1): 51–55.

19.

Vereecken

Roels

(2011) A numerical study of the hygrothermal performance of capillary active interior insulation systems. In: Proceedings of the 9th Nordic symposium on building physics (NSB 2011), Tampere, 29 May–2 June, vol. 1, pp. 365–372. Tampere: Department of Civil Engineering, Tampere University of Technology.

20.

Vesikari

(1998) Prediction of service life of concrete structures by computer simulation. Licentiate’s Thesis, Helsinki University of Technology, Espoo, 131 pp.

21.

Viitanen

Ojanen

(2007) Improved model to predict mold growth in building materials. In: Proceedings of the thermal performance of the exterior envelopes of buildings X, Clearwater Beach, FL, 2–7 December.

22.

Viitanen

Vinha

Salminen

. (2010) Moisture and bio-deterioration risk of building materials and structures. Journal of Building Physics 33(3): 201–224.

23.

Vinha

Valovirta

Korpi

. (2005) Rakennusmateriaalien rakennusfysikaaliset ominaisuudet lämpötilan ja suhteellisen kosteuden funktiona. Tampere: Tampere University of Technology.

24.

Zhao

Plagge

Grunewald

(2011) Performance assessment of interior insulations by stochastic method. In: Proceedings of the 9th Nordic symposium on building physics (NSB 2011), Tampere, 29 May–2 June, vol. 1, pp. 465–472. Tampere: Department of Civil Engineering, Tampere University of Technology.