In this study, several years of field measurements of indoor hygrothermal loads in 237 dwelling units are analysed. Moisture excess is calculated from hourly values of temperature, and relative humidity measured both indoors and outdoors. Air change rate and moisture production in bedrooms are calculated on the basis of carbon dioxide measurements. It is found that indoor temperature profiles differ depending on whether a building has central heating, a stove or combined heating system. The determined average moisture excess value, 2.8 g/m3 with a standard deviation of 1.6 g/m3 for cold periods, can be used in stochastic calculations. Critical values for moisture excess at the 90th percentile, ranging from 3–8 g/m3, depending upon occupancy rates, can be used in the deterministic analysis. Averages and weekly maxima of moisture excess in the study are reported at different percentiles. Considerable deviations from the EN ISO 13788 standard are discovered, concerning the breaking point depending on outdoor temperature and moisture excess during the summer. The average and critical moisture production in bedroom is presented and insufficient ventilation determined based on measurements. During the heating period, the air change rate is relatively stable while moisture production levels increase along with the dropping outdoor temperature. Two indoor temperatures and three humidity models with different levels of detail and influencing factors are proposed. Temperature and humidity loads derived using the proposed models can be used to determine the indoor hygrothermal boundary conditions for the building envelope of dwellings in cold climates.
ArenaLBlanfordM (2010) Monitoring of internal moisture loads in residential buildings. In: Proceedings of Building Enclosure Scienbce and Technology (BEST2), Portland, OR, 12–14 April 2010, 1–28.
2.
ASHRAE 160P (2009) Criteria for Moisture Control Design Analysis in Buildings. Atlanta, GA: ASHRAE.
3.
ASHRAE 55 (2004) Thermal Environmental Conditions for Human Occupancy. Atlanta, GA: ASHRAE.
BeckerRPaciukM (2009) Thermal comfort in residential buildings – failure to predict by Standard model. Building and Environment44: 948–960.
6.
BeköGLundTNorsFet al. (2010) Ventilation rates in the bedrooms of 500 Danish children. Building and Environment45(10): 2289–2295.
7.
BisharaAHauplPHanselF (2014) Model and program for the prediction of the indoor air temperature and indoor air relative humidity. Journal of Building Physics38(2): 103–120.
8.
BornehagCGSundellJBoniniSet al. (2004) Dampness in buildings as a risk factor for health effects, EUROEXPO: a multidisciplinary review of the literature (1998–2000) on dampness and mite exposure in buildings and health effects. Indoor Air14(4): 243–257.
9.
Construction Products Regulation (CPR) (2011) Construction products regulation (Regulation (EU) No. 305/2011: 39) Annex I. Official Journal of the European Union.
10.
CornickSMKumaranMK (2008) A comparison of empirical indoor relative humidity models with measured data. Journal of Building Physics31(3): 243–268.
11.
CuiSCohenMStabatPet al. (2015) CO2 tracer gas concentration decay method for measuring air change rate. Building and Environment84: 162–169.
12.
DimitroulopoulouC (2012) Ventilation in European dwellings: a review. Building and Environment47: 109–125.
13.
EN 13829 (2000) Thermal Performance of Buildings: Determination of Air Permeability of Buildings: Fan Pressurization Method. Brussels, Belgium.
14.
EN 15026 (2007) Hygrothermal Performance of Building Components and Building Elements: Assessment of Moisture Transfer by Numerical Simulation. Brussels, Belgium.
15.
EN 15251 (2007) Indoor Environmental Input Parameters for Design and Assessment of Energy Performance of Buildings Addressing Indoor Air Quality, Thermal Environment, Lighting and Acoustics. Brussels, Belgium.
16.
EN ISO 13788 (2012) Hygrothermal Performance of Building Components and Building Elements: Internal Surface Temperature to Avoid Critical Surface Humidity and Interstitial Condensation: Calculation Methods. Brussels, Belgium.
17.
FiskWJLei-GomezQMendellMJ (2007) Meta-analyses of the associations of respiratory health effects with dampness and mold in homes. Indoor Air17(4): 284–296.
18.
FranciscoPWRoseWB (2010) Temperature and humidity measurements in 71 homes participating in an IAQ improvement program. In: Proceedings of the Thermal Performance of the Exterior Envelopes of Whole Buildings XI International Conference, 5–9 December 2010, Clearwater, FL. Atlanta, GA: ASHRAE.
19.
GevingSHolmeJ (2011) Mean and diurnal indoor air humidity loads in residential buildings. Journal of Building Physics35(4): 392–421.
20.
GlassSVTenwoldeA (2009) Review of moisture balance models for residential indoor humidity. In: Proceedings of the 12th Canadian Conference on Building Science and Technology, Montreal, QC, Canada, 6–8 May 2009, 231–246.
IEA EBC Annex 55 (2012) Reliability of Energy Efficient Building Retrofitting -Probability Assessment of Performance and Cost (ed HagentoftCE) Gothenburg, Sweden.
23.
IOM (2004) Damp Indoor Spaces and Health: Health San Francisco. Washington, DC: The National Academy of Sciences Press.
24.
JanssensAVandepitteA (2006) Analysis of indoor climate measurements in recently built Belgian dwellings. In: Proceedings of Annex 41 Moist-Eng Working Meeting, Lyon, 25–27 October 2006.
25.
JonesR (1993) Modelling water vapour conditions in buildings. Building Services Engineering Research and Technology14(3): 99–106.
26.
KalameesTVinhaJKurnitskiJ (2006) Indoor humidity loads and moisture production in lightweight timber-frame detached houses. Journal of Building Physics29(3): 219–246.
LabatMWoloszynM (2016) Moisture balance assessment at room scale for four cases based on numerical simulations of heat – air – moisture transfers for a realistic occupancy scenario. Journal of Building Performance Simulation9(5): 487–509.
29.
MikolaAKõivTKalameesT (2013) Quality of ventilation systems in residential buildings: status and perspectives in Estonia. In: Proceedings of the International Workshop Securing the Quality of Ventilation Systems in Residential Buildings: Status and Perspectives, Brussels, 18–19 March.
30.
MikolaAKõivTRehandJ (2017) The usage of CO2 tracer gas methods for ventilation performance evaluation in apartment buildings. In: Proceedings of the 10th International Environmental Engineering Conference, Vilnius, 27–28 April.
31.
MlakarJŠtrancarJ (2013) Temperature and humidity profiles in passive-house building blocks. Building and Environment60: 185–193.
32.
PallinS (2013) Risk assessment of hygrothermal performance: building envelope retrofit. Doctoral Thesis, Chalmers University of Technology, Gothenburg.
33.
PeetersLDearRDe HensenJet al. (2009) Thermal comfort in residential buildings: Comfort values and scales for building energy simulation. Applied Energy86: 772–780.
34.
RousseauMManningMSaidMNet al. (2007) Characterization of indoor hygrothermal conditions in houses in different northern climates. In: Proceedings of the X International Conference on Thermal Performance of Exterior Envelopes of Whole Buildings, Clearwater, Fl, 2 December, 1–14.
35.
SandersC (1996) Heat, Air and Moisture Transfer in Highly Insulated Building Envelopes (HAMTIE): Report, Volume 2, Task 2: Environmental Conditions, Belgium, KU Leuven, 96pp.
36.
TajimaMInoueTOhnishiY (2014) Derivation of equation for personal carbon dioxide in exhaled breath intended to estimation of building ventilation. In: Proceedings of the 35th AIVC Conference ‘Ventilation and Airtightness in Transforming the Building Stock to High Performance’, 24–25 September, Poznań.
37.
TarikuFSimpsonWY (2014) Temperature and humidity distributions in a mid-rise residential building suite. In: Proceedings of the 14th Canadian Conference on Building Science and Technology, 28–30 October 2014, Toronto, ON, Canada, 419–428.
38.
TarikuFKumaranKFazioP (2011) Determination of indoor humidity profile using a whole-building hygrothermal model. Building Simulation4(1): 61–78.
39.
WoloszynMRodeC (2008) Final Report of IEA Annex 41, Subtask 1: Modelling Principles and Common Exercises. Leuven: Department of Civil Engineering Laboratory of Building Physics, KU Leuven.
40.
ZhangHYoshinoHMurakamiSet al. (2007) Investigation of actual humidity conditions in houses and evaluation of indoor environment by fungal index. In: Proceedings of the 6th International Conference on Indoor Air Quality, Ventilation & Energy Conservation in Buildings (IAQVEC), 28–31 October 2007, Sendai, Japan, 6.
