This study investigates the influence of waste tire rubber (WTR) on the liquid-phase moisture transport properties in cement mortar under ambient conditions—an area that is still insufficiently explored in current literature. While most studies have focused on mechanical performance, this work integrates capillary absorption testing with a liquid-phase moisture transfer model calibrated using experimental data to quantify sorptivity and water diffusivity. Seven mortar mixtures were prepared: one control (no WTR), three with WTR powder replacing 7%, 14%, and 21% of sand by volume, and three with rubber aggregates at the same replacement levels. The study systematically compares the effects of WTR in both powder and aggregate forms on key parameters such as sorptivity, water diffusivity, accessible porosity, and compressive strength. Capillary absorption tests provided empirical data for model calibration and analysis of liquid-phase moisture transfer behavior. Results showed that WTR substitutions up to 14% reduced accessible porosity by 18.03% and sorptivity by up to 351%, attributed to the hydrophobic nature of rubber, which impedes capillary flow. However, at a 21% replacement level, both porosity and sorptivity increased, while compressive strength declined—indicating that high WTR content compromises mechanical integrity and limits suitability for structural use. Water diffusivity exhibited two regimes: a low-diffusivity phase (<0.01 mm2/s) under partial saturation, and a higher-diffusivity phase at near-saturation, consistent with dual-regime moisture transfer models. WTR incorporation led to more tortuous pore structures, which reduced water ingress and improved moisture resistance. WTR powder was more effective than rubber aggregates in reducing sorptivity and porosity, particularly at replacement levels up to 14%. WTR powder at replacement levels up to 14% improved moisture resistance, suggesting its potential use in non-structural cement elements such as renders and plaster coatings. The results clarify how WTR particle morphology influences pores connectivity and liquid-phase moisture transfer, supporting its potential for enhancing durability in moisture-sensitive, non-load-bearing cement applications.
AFPC-AFREM (1997) Sur la durabilité des bétons. Méthodes recommandées pour la mesure des grandeurs associées à la durabilité des bétons. INSA-LMDC.
2.
Al-AttarAAHamadaHMTayehBA, et al. (2022) Exploring engineering properties of waste tire rubber for construction applications - a review of recent advances. Materials Today Proceedings53(2): A1–A17.
3.
Alawi Al-SodaniKA (2022) Mix design, mechanical properties and durability of the rubberized geopolymer concrete: A review. Case Studies in Construction Materials17: e01480.
4.
Al-MansourAYangRXuC, et al. (2022) Enhanced recyclability of waste plastics for waterproof cementitious composites with polymer-nanosilica hybrids. Materials & Design224: 111338.
5.
ASTM International (2014) ASTM C136/C136M-14: Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates. ASTM International.
6.
ASTM International (2017) ASTM C29/C29M-17a: Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate. ASTM International.
7.
BaiJWildSSabirBB (2003) Sorptivity and strength of air-cured and water-cured PC–PFA–MK concrete and the influence of binder composition on carbonation depth. Cement and Concrete Research32: 1813–1821.
8.
BajiHYangWLiC-Q, et al. (2019) Analytical models for effective hydraulic sorptivity, diffusivity and conductivity of concrete with interfacial transition zone. Construction and Building Materials225: 555–568.
9.
BenazzoukADouzaneOLangletT, et al. (2007) Physico-mechanical properties and water absorption of cement composite containing shredded rubber wastes. Cement and Concrete Composites29(10): 732–740.
10.
BravoMde BritoJ (2012) Concrete made with used tyre aggregate: Durability-related performance. Journal of Cleaner Production25: 42–50.
11.
British Standards Institution (1995) Methods of testing cement, Part 1: Determination of strength. EN standard No. BS EN 196-1. Available at: http://bsonline.techindex.co.uk
12.
CouasnetY (1986) Les condensations dans les bâtiments. Presses des Ponts et Chaussées, p.319.
13.
DaianJF (1986) Processus de condensation et de transfert d’eau dans un matériau méso et macroporeux. Presses du CNRS, p.560.
14.
De VriesDA (1987) The theory of heat and moisture transfer in porous media revisited. International Journal of Heat and Mass Transfer30(7): 1343–1350.
15.
European Standard (1999) EN 1015-3 - Methods of test for mortar masonry- Part 3: Determination of consistence of fresh mortar (by flow table). European Committee for Standardization (CEN).
16.
FadielAAl RifaieFTaherA-L, et al. (2014) Use of crumb rubber to improve thermal efficiency of cement-based materials. American Journal of Engineering and Applied Sciences7(1): 1–11.
17.
GhizdaveţZStefanBMNastacD, et al. (2016) Sound absorbing materials made by embedding crumb rubber waste in a concrete matrix. Construction and Building Materials124: 755–763. https://dx-doi-org-s.web.bisu.edu.cn/10.1016/j.conbuildmat.2016.07.145
18.
GoualMSBarquinFBenmalekML, et al. (2002) Estimation of the capillary transport coefficient of clayey aerated concrete using a gravimetric technique. Cement and Concrete Research30: 201–207.
19.
GuelmineL (2006) Influence du rapport E/C et du mode de cure sur les propriétés physico-mécaniques et de transfert d’humidité des mortiers de ciment durcis. Mémoire de Magister, Université Amar Telidji de Laghouat, p.86. Available at: https://www.ccdz.cerist.dz/admin/notice.php?id=120310 (accessed June 2025).
20.
GuelmineL (2017) Contribution à l’étude de la durabilité de composite cimentaire incorporant les granulats des pneus usés sous l’effet d’un gel et de hautes températures. Doctorat: Construction et Matériaux. Faculté de Génie Civil, Université des sciences et de la technologie Houari Boumediène, Alger, p.134. Available at: https://www.ccdz.cerist.dz/admin/notice.php?id=00000000000000837924000104 (accessed June 2025).
21.
GuelmineL (2022) The freeze-thaw durability of concrete containing the rubber aggregate of tire waste. Research on Engineering Structures and Materials8(2): 253–264.
22.
GuelmineLHadjabH (2021) Effect of recycled rubber particles on the deicing salt-scaling durability of concrete. Recent Progress in Materials03: 1.
23.
GuelmineLHadjabHBenazzoukA (2016) Effect of elevated temperatures on physical and mechanical properties of recycled rubber mortar. Construction and Building Materials126: 77–85.
GuelmineLSadekDHadjabH, et al. (2022) Effect of recycled rubber powder on the compatibility of rubber-cement paste. Annales de Chimie - Science des Matériaux46: 135–139.
26.
HallCTseTKM (1986) Water movement in the porous building materials-VII. The sorptivity of mortar. Building and Environment21(2): 113–118.
27.
HanžičLIlićR (2003) Relationship between liquid sorptivity and capillarity in concrete. Cement and Concrete Research33(9): 1385–1388.
28.
HossainMMKarimMRA ElahiMM, et al. (2020) Water absorption and sorptivity of alkali-activated ternary blended composite binder. Journal of Building Engineering31: 101370.
29.
IbroMAVerdierJGeoffroyS, et al. (2021). Prediction of moisture transfer in cement-based materials: Use of a porous network model to access transfer parameters. Cement and Concrete Research, 142, 106310. https://doi.org/10.1016/j.cemconres.2020.106310
30.
JiangJWangFGuoW, et al. (2021) Hydraulic transport properties of unsaturated cementitious composites with spheroidal aggregates. International Journal of Mechanical Sciences212: 106845.
31.
KarahanOÖzbayEHossainKMA, et al. (2012) Fresh, mechanical, transport, and durability properties of self-consolidating rubberized concrete. ACI Materials Journal109: 413–420.
32.
KashaniANgoTDHemachandraP, et al. (2018) Effects of surface treatments of recycled tyre crumb on cement-rubber bonding in concrete composite foam. Construction and Building Materials171: 467–473.
33.
KaushikAPrakashGRajputA (2022) Influence of crumb rubber on the response of concrete beams against low velocity impact. Construction and Building Materials347: 128614.
34.
KevernJTSchaeferVR (2013) Mixture proportioning considerations for improved freeze-thaw durability of pervious concrete. In: Proceedings of ISCORD 2013: Planning for Sustainable Communities, American Society of Civil Engineers, Reston, VA. pp.471–482. https://doi.org/10.1061/9780784412978.046
35.
KubissaWJaskulskiRGrzelakM (2021) Torrent air permeability and sorptivity of concrete made with the use of air entraining agent and citric acid as setting retardant. Construction and Building Materials268: 121703. https://doi.org/10.1016/j.conbuildmat.2020.121703
36.
LianCZhugeYBeechamS (2011) The relationship between porosity and strength for porous concrete. Construction and Building Materials25(11): 4294–4298.
37.
LiMQingLChenH, et al. (2025) Insights into pore tortuosity and diffusivity of cement paste via hydration model with superovoidal cement particles. Journal of Building Engineering99: 111654.
38.
MarquesACAkasakiJLTrigoAPM, et al. (2008) Influence of the surface treatment of tire rubber residues added in mortars. Revista IBRACON de Estruturas e Materiais1(2): 113–120.
39.
McGlinnPJde BeerFCAldridgeLP, et al. (2010) Appraisal of a cementitious material for waste disposal: Neutron imaging studies of pore structure and sorptivity. Cement and Concrete Research40(8): 1320–1326.
40.
MezidiAMerabtiSGuelmineL, et al. (2025) Effect of crumb rubber on the fresh and hardened properties of dune sand concrete. Advanced Material Science25(2): 5–16.
41.
NisticòRLavagnaLBootEA, et al. (2021) Improving rubber concrete strength and toughness by plasma-induced end-of-life tire rubber surface modification. Plasma Processes and Polymers18: e2100081.
42.
OzbayELachemiMSevimUK (2011) Compressive strength, abrasion resistance and energy absorption capacity of rubberized concretes with and without slag. Materials and Structures44: 1297–1307.
43.
PedroDde BritoJVeigaR (2013) Mortars made with fine granulate from shredded tires. Journal of Materials in Civil Engineering25(4): 519–529.
44.
PelisserFBarcelosASantosD, et al. (2012) Lightweight concrete production with low Portland cement consumption. Journal of Cleaner Production23(1): 68–74.
45.
PhilipJRDe VriesDA (1957) Moisture movement in porous materials under temperature gradients. Transactions American Geophysical Union38(2): 222–232.
46.
QaidiSMAMohammedASAhmedHU, et al. (2022) Rubberized geopolymer composites: A comprehensive review. Ceramics International48(17): 24234–24259.
47.
RashadAM (2016) A comprehensive overview about recycling rubber as fine aggregate replacement in traditional cementitious materials. International Journal of Sustainable Built Environment5(1): 46–82.
48.
RenFZhouCLiL, et al. (2023) Modeling the dependence of capillary sorptivity on initial water content for cement-based materials in view of water sensitivity. Cement and Concrete Research168: 107158.
49.
RöβlerMOdlerI (1985) Investigations on the relationship between porosity, structure and strength of hydrated Portland cement pastes I: Effect of porosity. Cement and Concrete Research15(2): 320–330.
50.
SaadAGSakrMAKhalifaTM, et al. (2024) Structural performance of concrete reinforced with crumb rubber: A review of current research. Iranian Journal of Science and Technology: Transactions of Civil Engineering49: 3211–3254. https://doi.org/10.1007/s40996-024-01629-w
51.
SinghPSinghDNDebbarmaS (2023) Macro- and micro-mechanisms associated with valorization of waste rubber in cement-based concrete and thermoplastic polymer composites: A critical review. Construction and Building Materials371: 130807.
52.
SiRGuoSDaiQ (2017) Durability performance of rubberized mortar and concrete with NaOH-solution treated rubber particles. Construction and Building Materials153: 496–505. http://doi.org/10.1016/j.conbuildmat.2017.07.085
53.
SukontasukkulP (2009) Use of crumb rubber to improve thermal and sound properties of pre-cast concrete panel. Construction and Building Materials23(2): 1084–1092.
54.
SukontasukkulPTiamlomK (2012) Expansion under water and drying shrinkage of rubberized concrete mixed with crumb rubber with different size. Construction and Building Materials29: 520–526.
55.
ThomasBSGuptaRCKallaP, et al. (2014) Strength, abrasion and permeation characteristics of cement concrete containing discarded rubber fine aggregates. Construction and Building Materials59: 204–212.
56.
TurkiMBretagneERouisMJ, et al. (2009) Microstructure, physical and mechanical properties of mortar–rubber aggregates mixtures. Construction and Building Materials23: 2715–2722.
57.
UygunoğluTTopçuİB (2010) The role of scrap rubber particles on the drying shrinkage and mechanical properties of self-consolidating mortars. Construction and Building Materials24(7): 1141–1150.
58.
ValentiniFPegorettiA (2022) End-of-life options of tyres. A review. Advanced Industrial and Engineering Polymer Research5(4): 203–213.
59.
XiongQXTongLYZhangZ, et al. (2023) A new analytical method to predict permeability properties of cementitious mortars: The impacts of pore structure evolutions and relative humidity variations. Cement and Concrete Composites137: 104912.
60.
YuJWangHSunX, et al. (2024) Characterizing connectivity and tortuosity of pore network based on LF-NMR method to assess the water permeability of white cement mortar. Journal of Building Engineering93: 109862.
61.
ZhangSPZongL (2014) Evaluation of relationship between water absorption and durability of concrete materials. Advances in Materials Science and Engineering2014: 1–8.
62.
ZhangZThieryMBaroghel-BounyV (2016) Investigation of moisture transport properties of cementitious materials. Cement and Concrete Research89: 257–268.
63.
ZhouCChenWWangW, et al. (2016) Indirect assessment of hydraulic diffusivity and permeability for unsaturated cement-based material from sorptivity. Cement and Concrete Research82: 117–129.
