The primary objective of this research paper is to control the material and process defects in polymer melt extrusion film casting (EFC) process for linear chain architecture polyethylene (PE) resins through polymer blending methodology. Extrusion film casting is a well-known industrially important manufacturing process that is used to manufacture thousands of tons of polymer/plastic films/sheets and coated products. In this research, the necking defect in an EFC process has been studied experimentally for a linear low density polyethylene (LLDPE) resin and attempts have been made to control its necking by blending in a long chain branched (LCB) low density polyethylene (LDPE) resin. The blending methodology is based on the understanding that a LDPE resin displays enhanced resistance to necking as compared to the LLDPE resin. It is found that added LDPE resin enhances necking resistance for the primary LLDPE resin. Further, as the LDPE concentration increases in the blend formulation, the necking is further reduced as compared to pure LLDPE. Analogous to past studies on EFC of linear and long chain branched architecture containing PEs, it is observed that as the LDPE is increased in the blend formulations, the formulations displayed enhanced melt elasticity and extensional strain hardening in rheological studies. It is concluded from this study that polyethylene resins having linear chain architecture can be made amenable to enhanced resistance to necking using appropriate amount of a long chain branched resins. Finally, process defects such as the draw resonance onset could be shifted to higher draw ratios as the LDPE level is increased in the LLDPE-LDPE blend formulation.
PolHBanikSAzadLB, et al.Nonisothermal analysis of extrusion film casting process using molecular constitutive equations. Rheol Acta2014; 53: 85–101. DOI: 10.1007/s00397-013-0739-x (accessed 6 January 2001).
3.
ChikhalikarKBanikSAzadLB, et al.Extrusion film casting of long chain branched polypropylene. Polym Eng Sci2015; 55: 1977–1987. DOI: 10.1002/pen.24039 (accessed 22 December 2001).
4.
VaggaAAherraoSPolH, et al.Flow visualization by Matlab® based image analysis of high-speed polymer melt extrusion film casting process for determining necking defect and quantifying surface velocity profiles. Adv Ind Eng Polym Res2021; 5: 1–11. https://linkinghub-elsevier-com-s.web.bisu.edu.cn/retrieve/pii/S2542504821000117
5.
D’HalewynSAgassantJ-FDemayY. Numerical simulation of the cast film process. Polym Eng Sci1990; 30: 335–340.
6.
BarqPHaudinJMAgassantJF, et al.Instability phenomena in film casting process. Int Polym Process1990; 5: 264–271. DOI: 10.3139/217.900264
7.
BarqPHaudinJAgassantJ-F. Isothermal and anisothermal models for cast film extrusion. Int Polym Process1992; 4: 334–349. DOI: 10.3139/217.920334 (accessed 28 January 2001).
8.
BarqPHaudinJMAgassantJF, et al.Stationary and dynamic analysis of film casting process. Int Polym Process1994; 9: 350–358. DOI: 10.3139/217.940350
9.
SilagyDDemayYAgassantJ-F. Study of the stability of the film casting process. Polym Eng Sci1996; 36: 2614–2625. DOI: 10.1002/pen.10661
10.
SilagyDDemayYAgassantJF. Stationary and stability analysis of the film casting process. J Non-Newton Fluid Mech1998; 79: 563–583. DOI: 10.1016/S0377-0257(98)00119-0
11.
SilagyDDemayYAgassantJ-F. Numerical simulation of the film casting process. Int J Numer Methods Fluids1999; 30: 1–18.
12.
SollogoubCDemayYAgassantJF. Technological solutions to reduce the geometrical defects during the cast film process. In: Proceedings of 22nd Annual Meeting of the Polymer Processing Society. Yamagata, Japan, 2006, pp. 2–3.
13.
AgassantJ-FBouamraRPeitiC, et al.Cast film extrusion, geometrical defects and stability. In: Proceedings of 22nd Annual Meeting of the Polymer Processing Society. Japan, Yamagata, 2–6 July 2006.
14.
DemayYAgassantJ. An overview of molten polymer drawing instabilities. Int Polym Process2014; 29: 1–24. DOI: 10.3139/217.2832 (accessed 13 August 2001).
15.
SeayCWBairdDG. Sparse long-chain branching’s effect on the film-casting behavior of PE. Int Polym Process2009; 24: 41–50. DOI: 10.3139/217.2184
16.
McGradyCDSeayCWBairdDG. Effect of sparse long-chain branching on the film-casting behavior for a series of well-defined HDPEs. Int Polym Process2009; 24: 428–438. DOI: 10.3139/217.2291
17.
IyengarRCoA. Film casting of a modified Giesekus fluid: a steady-state analysis. J Non-Newton Fluid Mech1993; 48: 1–20.
18.
IyengarVRCoA. Film casting of a modified giesekus fluid: stability analysis. Chem Eng Sci1996; 51: 1417–1430.
19.
AnturkarNRCoA. Draw resonance in film casting of viscoelastic fluids: a linear stability analysis. J Non-Newton Fluid Mech1988; 28: 287–307. DOI: 10.1016/0377-0257(88)87002-2
20.
CanningKCoA. Edge effects in film casting of molten polymers. J Plast Film Sheeting2000; 16: 188–203. DOI: 10.1106/G0MF-N3HC-3DJ1-WLJ1
21.
CanningKBianBCoA. Film casting of a low density polyethylene melt. J Reinf Plast Compos2001; 20: 366–376. DOI: 10.1177/073168401772678698
22.
ItoHDoiMIsakiT, et al.A model of neck-in phenomenon in film casting process. J Soc Rheol Japan2003; 31: 157–163.
23.
ItoHDoiMIsakiT, et al.2D flow analysis of film casting process. J Soc Rheol Japan2003; 31: 149–155.
24.
MorikawaMMasutaniYShiromotoS. Development and simulation of extrusion lamination process, 2009.
25.
ShiromotoSMasutaniYTsutsubuchiM, et al.A neck-in model in extrusion lamination process. Polym Eng Sci2010; 50: 22–31.
26.
ShiromotoSMasutaniYTsutsubuchiM, et al.The effect of viscoelasticity on the extrusion drawing in film-casting process. Rheol Acta2010; 49: 757–767. DOI: 10.1007/s00397-010-0454-9 (accessed 13 August 2001).
27.
PolHVTheteSS. Necking in extrusion film casting: numerical predictions of the maxwell model and comparison with experiments. J Macromol Sci B Phys2016; 55: 984–1006. DOI: 10.1080/00222348.2016.1225556
28.
DhadwalRBanikSDoshiP, et al.Effect of viscoelastic relaxation modes on stability of extrusion film casting process modeled using multi-mode Phan-Thien-Tanner constitutive equation. Appl Math Model2017; 47: 487–500. DOI: 10.1016/j.apm.2017.03.010
29.
TheteSSDoshiPPolHV. New insights into the use of multi-mode phenomenological constitutive equations to model extrusion film casting process. J Plast Film Sheeting2017; 33: 35–71. DOI: 10.1177/8756087915627843
30.
ChougaleSRokadeDBhattacharjeeT, et al.Non-isothermal analysis of extrusion film casting using multi-mode Phan-Thien Tanner constitutive equation and comparison with experiments. Rheol Acta2018; 57: 493–503. DOI: 10.1007/s00397-018-1095-7
31.
RokadeDAzadLBPoddarS, et al.Controlling necking in extrusion film casting using polymer nanocomposites. J Macromol Sci Part B: Phys2017; 56: 213–233. DOI: 10.1080/00222348.2017.1289797
32.
RokadeDChougaleSPatilP, et al.Controlling draw resonance during extrusion film casting of nanoclay filled linear low-density polyethylene: an experimental study and numerical linear stability analysis. J Plast Film Sheeting2021; 37: 367–396. DOI: 10.1177/8756087920978443
33.
AbrahamDGeorgeKEFrancisD. Flow behavior of LDPE and its blends with LLDPE I and II: a comparative study. J Appl Polym Sci1996; 62: 59–65. DOI: 10.1002/(SICI)1097-4628(19961003)62:1%3C59::AID-APP8%3E3.0.CO;2-R (accessed 8 July 2001).
34.
WongASyA. Effects of temperature and load on the melt index of LDPE/LLDPE blends of different blend ratios. J Mater Sci1995; 30: 5672–5680. DOI: 10.1007/BF00356704 (accessed 8 July 2001).
35.
AjjiASammutPHuneaultM. Elongational rheology of LLDPE/LDPE blends. J Appl Polym Sci2003; 88: 3070–3077. DOI: 10.1002/app.11931 (accessed 1 July 2001).
36.
LiangJ. The elastic behaviour during capillary extrusion of LDPE/LLDPE blend melts. Polym Test2002; 21: 69–74.
37.
HusseinIWilliamsMC. Rheological study of the miscibility of LLDPE/LDPE blends and the influence of T mix. Polym Eng Sci2001; 41: 696–701.
38.
CranMJBiggerSWScheirsJ. Characterizing blends of linear low-density and low-density polyethylene by DSC. J Therm Anal Calorim2005; 81: 321–327. DOI: 10.1007/s10973-005-0786-3
39.
SrivastavaD. Studies on mechanical and thermal properties of ternary blends of polyethylenes having fixed percentage of high-density polyethylene—II. Polym Plast Technol Eng, 2006; 45: 879–883. DOI: 10.1080/03602550600611784 (accessed 8 July 2001).
40.
HusseinIWilliamsMC. Rheological study of heterogeneities in melt blends of ZN-LLDPE and LDPE: influence of Mw and comonomer type, and implications for miscibility. Rheol Acta2004; 43: 602–614.
41.
Delgadillo-VelázquezOHatzikiriakosSGSentmanatM. Thermorheological properties of LLDPE/LDPE blends: effects of production technology of LLDPE. J Polym Sci Part B Polym Phys2008; 46: 1669–1683. DOI: 10.1002/polb.21504 (accessed 8 July 2001).
42.
Delgadillo-VelázquezOHatzikiriakosSG. Processability of LLDPE/LDPE blends: capillary extrusion studies. Polym Eng Sci2007; 47: 1317–1326. DOI: 10.1002/pen.20811 (accessed 8 July 2001).
43.
ChangACTauLHiltnerA, et al.Structure of blown film from blends of polyethylene and high melt strength polypropylene. Polymer2002; 43: 4923–4933. DOI: 10.1016/S0032-3861(02)00304-X
44.
ZhaoYZhangWYangD. Morphology and mechanical properties of melt-drawn films of blend of high-density polyethylene and ultrahigh-molecular-weight polyethylene. J Mater Sci Lett1993; 12: 1309–1312.
45.
ConradJ. The rheology, degradation, processing, and characterization of renewable resource polymers, 2009.
46.
SawatariCMatsuoM. Morphological and mechanical properties of ultrahigh-molecular-weight polyethylene/low-molecular-weight polyethylene blend films produced by gelation/crystallization from solutions. Polymer1989; 30: 1603–1614.
47.
OgitaTKawaharaYSawatariC, et al.Morphological properties of ultrahigh molecular weight polyethylene and low molecular weight polypropylene blend gel films. Polym J1991; 23: 871–884.
48.
NiaounakisMKontouE. Effect of LDPE on the thermomechanical properties of LLDPE‐based films. J Polym Sci B2005; 43: 1712–1727. DOI: 10.1002/polb.20473 (accessed 8 July 2001).
49.
FangYCarreauPJLafleurPG. Thermal and rheological properties of mLLDPE/LDPE blends. Polym Eng Sci2005; 45: 1254–1264. DOI: 10.1002/pen.20401 (accessed 8 July 2001).
50.
van GurpMPalmenJ. Time-temperature superposition for polymeric blends. Rheol Bull1998; 6: 5–8.
51.
TrinkleSFriedrichC. Van Gurp-Palmen-plot: a way to characterize polydispersity of linear polymers. Rheol Acta2001; 40: 322–328. DOI: 10.1007/s003970000137
52.
Delgadillo-VelázquezOHatzikiriakosSGSentmanatM. Thermorheological properties of LLDPE/LDPE blends. Rheol Acta2007; 47: 19–31. DOI: 10.1007/s00397-007-0193-8 (accessed 13 August 2001).
53.
GraessleyWW. Effect of long branches on the temperature dependence of viscoelastic properties in polymer melts. Macromolecules1982; 15: 1164–1167. DOI: 10.1021/ar50117a004
54.
ColbyR. Breakdown of time-temperature superposition in miscible polymer blends. Polymer1989; 30: 1275–1278. DOI: 10.1016/0032-3861(89)90048-7
55.
CoxWPMerzEH. Correlation of dynamic and steady flow viscosities. J Polym Sci1958; 28: 619–622.
56.
WangJPorterRS. On the viscosity-temperature behavior of polymer melts. Rheol Acta1995; 34: 496–503. DOI: 10.1007/BF00396562
57.
GraessleyWW. Effect of long branches on the temperature dependence of viscoelastic properties in polymer melts. Acc Chem Res1977; 10: 332–339.
58.
YamaguchiMAbeS. LLDPE/LDPE blends. I. rheological, thermal, and mechanical properties. J Appl Polym Sci1999; 74: 3153–3159.
59.
WagnerMHKheirandishSYamaguchiM. Quantitative analysis of melt elongational behavior of LLDPE/LDPE blends. Rheol Acta2004; 44: 198–218. DOI: 10.1007/s00397-004-0400-9
60.
PadmanabhanMKasehagenLJMacoskoCW. Transient extensional viscosity from a rotational shear rheometer using fiber‐windup technique. J Rheol1996; 40: 473–481. DOI: 10.1122/1.550792
61.
HusseinI. Melt miscibility and mechanical properties of metallocene linear low-density polyethylene blends with high-density polyethylene: influence of comonomer type. Polym Int2005; 54: 1330–1336. DOI: 10.1002/pi.1860 (accessed 8 July 2001).
WagnerMBastianHHachmannP, et al.The strain-hardening behaviour of linear and long-chain-branched polyolefin melts in extensional flows. Rheol Acta2000; 39: 97–109. DOI: 10.1007/s003970050010 (accessed 24 June 2001).
64.
Rolón-GarridoVHWagnerMH. The MSF model: relation of nonlinear parameters to molecular structure of long-chain branched polymer melts. Rheol Acta2006; 46: 583–593. DOI: 10.1007/s00397-006-0136-9 (accessed 13 August 2001).
65.
NarimissaERolonn-GarridoVHWagnerMH. A hierarchical multi-mode MSF model for long-chain branched polymer melts part I: elongational flow. Rheol Acta2015; 54: 779–791. DOI: 10.1007/s00397-016-0922-y
66.
LagendijkRPHogtAHBuijtenhuijsA, et al.Peroxydicarbonate modification of polypropylene and extensional flow properties. Polymer2001; 42: 10035–10043.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
