This paper investigates a trailing heat sink, which was designed and applied to friction stir welding (FSW) in order to control the residual stresses and welding distortion. Residual stresses, residual plastic strains and welding distortion of 2024-T3 and 5083-H321 Al sheets welded by FSW with and without the trailing heat sink were compared. The optimal placement of the heat sink was discussed. The results revealed that the reductions in peak tensile stresses were 66% for 2024-T3 and 58% for 5083-H321 by application of the trailing heat sink in FSW. In addition, the welding distortion could be reduced drastically by this method. The 5083-H321 sheet with a size of 1000×100×3·5 mm welded by this method was very flat and had almost no distortion. This method achieved in-process control of stresses and welding distortion, without additional complicated work before or after welding operation.
AmancioST, SheikhiS, dos SantosJF, BolfariniC: ‘Preliminary study on the microstructure and mechanical properties of dissimilar friction stir welds in aircraft aluminium alloys 2024-T351 and 6056-T4’, J. Mater. Process. Technol., 2008, 206, 132–142.
PeelM, SteuwerA, PreussM, WithersPJ: ‘Microstructure, mechanical properties and residual stresses as a function of welding speed in aluminium AA5083 friction stir welds’, Acta Mater., 2003, 51, 4791–4801.
4.
StaronP, KocakM, WilliamsS: ‘Residual stress distributions in friction stir welded Al sheets determined by neutron strain scanning’, Proc. 6th Int. Conf. on ‘Trends in welding research’, Phoenix, AZ, USA, April 2002, ASM International, 253–256.
5.
StaronP, KocakM, WilliamsS: ‘Residual stresses in friction stir welded Al sheets, neutrons in science and industry’, Proc. Int. Conf. on ‘Neutron scattering’, Munich, Germany, September 2001, Springer-Verlag, Vol. A74, 1161–1162.
AliA, AnX, RodopoulosCA, BrownMW, O'HaraP, LeversA, GardinerS: ‘The effect of controlled shot peening on the fatigue behaviour of 2024-T3 aluminium friction stir welds’, Int. J. Fatigue, 2007, 29, 1531–1545.
8.
WithersPJ: ‘Residual stress and its role in failure’, Rep. Prog. Phys., 2007, 70, 2211–2264.
9.
LombardH, HattinghDG, SteuwerA, JamesMN: ‘Effect of process parameters on the residual stresses in AA5083-H321 friction stir welds’, Mater. Sci. Eng. A, 2009, A501, 119–124.
10.
RichardsDG, PrangnellPB, WithersPJ, WilliamsSW, WescottA, OliverEC: ‘Geometry effects when controlling residual stresses in friction stir welds by mechanical tensioning’, Mater. Sci. Forum, 2006, 524–525, 71–76.
11.
RichardsDG, PrangnellPB, WilliamsSW, WithersPJ: ‘Global mechanical tensioning for the management of residual stresses in welds’, Mater. Sci. Eng. A, 2008, A489, 351–362.
12.
RichardsDG, PrangnellPB, WithersPJ, WilliamsSW, NagyT, MorganS: ‘Efficacy of active cooling for controlling residual stresses in friction stir welds’, Sci. Technol. Weld. Join., 2010, 15, (2), 156–165.
13.
GabzdylJ, ColeM, WilliamsSW, PriceD: ‘Control of laser weld distortion by thermal tensioning’, Proc. Int. Cong. on ‘Applications of lasers and electro-optics’, Orlando, FL, USA, October 2001, Laser Institute of America, 1236–1245.
14.
GabzdylJ, JohnsonA, WilliamsS, PriceD: ‘Laser weld distortion control by cryogenic cooling’, Proc. 1st Int. Symp. on ‘High-power laser macroprocessing’, Vol. 4831, Osaka, Japan, May 2002, SPIE-International Society for Optical Engineering, 269–274.
15.
SoulFA, ZhangYH: ‘Study of residual stresses and strains field during arc welding with trailing heat sink on titanium alloy sheet’, Rare. Met. Mater. Eng., 2006, 35, 256–260.
16.
LiJ, GuanQ, ShiY, GuoD, DuY, SunY: ‘Studies on characteristics of temperature field during GTAW with a trailing heat sink for titanium sheet’, J. Mater. Process. Technol., 2004, 147, 328–335.
LiJ, GuanQ, GuoD, SunY, DuY, ShiY: ‘Influence of heat sink position on welding residual stress of titanium alloy thin plate’, J. Mech. Strength, 2003, 25, 637–641.
19.
LiJ, GuanQ, GuoD.-L, DuY.-X, SunY.-C, ShiY.-W: ‘Experimental study on effect of heat sink on welding residual stress of titanium alloy thin plate’, Hanjie Xuebao/Trans. China Weld. Inst., 2003, 24, 29–32.
20.
MolliconeP, CamilleriD, GrayTGF, ComlekciT: ‘Simple thermo-elastic-plastic models for welding distortion simulation’, J. Mater. Process. Technol., 2006, 176, 77–86.
21.
ZhangH, ZhangG, CaiC, GaoH, WuL: ‘Fundamental studies on in-process controlling angular distortion in asymmetrical double-sided double arc welding’, J. Mater. Process. Technol., 2008, 205, 214–223.
22.
DengD, WeiL, MurakawaH: ‘Determination of welding deformation in fillet-welded joint by means of numerical simulation and comparison with experimental measurements’, J. Mater. Process. Technol., 2007, 183, 219–225.
23.
OzcatalbasY, VuralHI: ‘Determination of optimum welding sequence and distortion forces in steel lattice beams’, J. Mater. Process. Technol., 2009, 209, 599–604.
24.
BastierA, MaitournamMH, RogerF, Dang VanK: ‘Modelling of the residual state of friction stir welded plates’, J. Mater. Process. Technol., 2008, 200, 25–37.
25.
KimD, BadarinarayanH, KimJH, KimC, OkamotoK, WagonerRH, ChungK: ‘Numerical simulation of friction stir butt welding process for AA5083-H18 sheets’, Eur. J. Mech. A/Solids, 2010, 29A, 204–215.
26.
LiJ, PetersonGP, ChengP: ‘Three-dimensional analysis of heat transfer in a micro-heat sink with single phase flow’, Int. J. Heat Mass Transfer, 2004, 47, 4215–4231.
27.
JangSP, Sung JinK: ‘Fluid flow and thermal characteristics of a microchannel heat sink subject to an impinging air jet’, J. Heat Transfer, 2005, 127, 770–779.
28.
LouZQ, YapC, MujumdarAS: ‘A numerical study of a heat sink fin under a laminar impinging jet’, J. Electron. Packag., 2008, 130, 0345011–0345015.
29.
ZumbrunnenDA, AzizM: ‘Convective heat transfer enhancement due to intermittency in an impinging jet’,
J. Heat Transfer, 199, 115, 91–98.
30.
SibaEA, Ganesa-PillaiM, HarrisKT, Haji-SheikhA: ‘Heat transfer in a high turbulence air jet impinging over a flat circular disk’, J. Heat Transfer, 2003, 125, 257–265.
31.
Seok PilJ, Sung JinK, Kyung WookP: ‘Experimental investigation of thermal characteristics for a microchannel heat sink subject to an impinging jet, using a micro-thermal sensor array’, Sens. Actuators A, 2003, 105A, 211–224.
32.
CanM, EtemogluAB, AvciA: ‘Experimental study of convective heat transfer under arrays of impinging air jets from slots and circular holes’, Heat Mass Transfer, 2002, 38, 251–259.
33.
van der AaEM, HermansMJM, RichardsonIM, van der PersNM, DelhezR: ‘Experimental study of the influence of a trailing heat sink on the welding residual stress distribution’, Mater. Sci. Forum, 2006, 524, 479–484.
34.
DavisJR: ‘Aluminium and aluminium alloys’, 247–248; 1993, Materials Park, OH, ASM Information Society.
