Friction stir welding of co-cast aluminium clad sheet

Abstract

The effects of welding parameters on material consolidation are examined during friction stir butt welding of 2 mm Al 5083 alloy aluminium sheet with a surface cladding of Al 3025 alloy, which was co-cast from the melt. The influence of welding parameters on joint consolidation is investigated when tool revolutions per minute, travel speed and penetration depth were varied. It was found that modifying the pin of the welding tool to have a two-flat profile improves material consolidation and avoids defect formation during welding, and optimum welding parameters involve a combination of high tool rotation speed and travel speed. Optical and electron microscopy revealed that the integrity of the surface cladding layer could be maintained during friction stir welding while avoiding defect formation within the stir zone of the weld. The tensile strength of the joint was ∼58% of the base material due to softening within the stir zone.

Keywords

Friction stir welding Aluminum Clad Co-cast

Get full access to this article

View all access options for this article.

References

Mishra,

R. S.

and Ma,

Z. Y.

: ‘Friction stir welding and processing’, Mater. Sci. Eng. R, 2005, R50, 1–78.

Nandan,

, DebRoy,

and Bhadeshia,

H. K. D. H.

: ‘Recent advances in friction-stir welding—process, weldment structure and properties’, Prog. Mater. Sci., 2008, 53, 980–1023.

Threadgill,

P. L.

, Leonard,

A. J.

, Shercliff,

H. R.

and Withers,

P. J.

: ‘Friction stir welding of aluminum alloys’, Int. Mater. Rev., 2009, 54, (2), 49–93.

Nandan,

, Roy,

G. G.

and Debroy,

: ‘Numerical simulation of three dimensional heat transfer and plastic flow during friction stir welding’, Metall. Mater. Trans. A, 2006, 37A, (4), 1247–1259.

da Silva,

A. A. M.

, Arruti,

, Janeiro,

, Aldanondo,

, Alvarez,

and Echeverria,

: ‘Material flow and mechanical behaviour of dissimilar AA2024-T3 and AA7075-T6 aluminium alloys friction stir welds’, Mater. Des., 2011, 32, (4), 2021–2027.

Leal,

R. M.

, Leitao,

, Loureiro,

, Rodrigues,

D. M.

and Vilaca,

: ‘Material flow in heterogeneous friction stir welding of thin aluminium sheets: effect of shoulder geometry’, Mater. Sci. Eng. A, 2008, A498, (1–2), 384–391.

Zhao,

Y. H.

, Lin,

S. B.

, Qu,

F. X.

and Wu,

: ‘Influence of pin geometry on material flow in friction stir welding process’, Mater. Sci. Technol., 2006, 22, (1), 45–50.

Foroozmehr,

, Esmaeili,

, Lloyd,

D. J.

and Gallerneault,

: ‘Modeling of solutionizing and solute re-distribution in a co-cast bi-layer Al alloy system’, Metall. Mater. Trans. A, 2012, 43A, 1770–1780.

Izadi,

, Fallu,

, Abdel-Gwad,

, Liyanage,

and Gerlich,

A. P.

: ‘Analysis of tool geometry in dissimilar Al alloy friction stir welds using optical microscopy and serial sectioning’, Sci. Technol. Weld. Join., 2013, 18, (4), 307–313.

10.

Shukla,

A. K.

and Baeslack,

W. A.

: ‘Effect of process conditions on microstructure evolution and mechanical properties of friction stir welded thin sheet 2024-T3’, Proc. Int. Symp. on ‘Friction stir welding’, Saint Sauveur, Que., Canada, October 2006, TWI, Session 09A, Paper 43.

11.

Karlsson,

, Berqvist,

E. L.

and Larsson,

: ‘Application of friction stir welding to dissimilar welding’, Weld. World, 2002, 46, (1/2), 10–14.

12.

Xiao,

B. L.

, Wang,

, Bi,

Zhang,

and Ma,

Z. Y.

: ‘Friction stir welding of SiCp/Al composite and 2024 Al alloy’, Mater. Sci. Forum, 2010, 638–642, 1500–1505.

13.

Gerlich,

P. Su.

, Yamamoto,

and North,

T. H.

: ‘Material flow and intermixing during dissimilar friction stir welding’, Sci. Technol. Weld. Join., 2008, 13, (3), 254–264.

14.

Colegrove,

P. A.

and Shercliff,

H. R.

: ‘CFD modelling of friction stir welding of thick plate 7449 aluminium alloy’, Sci. Technol. Weld. Join., 2006, 11, 429–441.

15.

Su,

, Gerlich,

, North,

T. H.

and Bendzsak,

G. J.

: ‘Energy generation and stir zone dimensions in friction stir spot welds’, SAE Technical Paper 2006-01-0971, 2006.

16.

Mahoney,

M. W.

, Rhodes,

C. G.

, Flintoff,

J. G.

, Spurling,

R. A.

and Bingel,

W. H.

: ‘Properties of friction-stir-welded 7075 T651 aluminum’, Metall. Mater. Trans. A, 1998, 29A, 1955–1964.

17.

Lin,

S.-B.

, Yan-Hua,

, Zi-Qiu,

and Lin,

: ‘Modeling of friction stir welding process for tools design’, Front. Mater. Sci., 2011, 5, (2), 236–245.

18.

Kumar,

, Kailas,

S. V.

and Srivatsan,

T. S.

: ‘The role of tool design in influencing the mechanism for the formation of friction stir welds in aluminum alloy 7020’, Mater. Manuf. Processes, 2011, 26, (7), 915–921.