The microstructure and mechanical properties of the deposited metals of five metal cored wires for welding 600–900 MPa ultralow carbon bainitic steels were investigated. It was found that lowering the C content and optimising the Mn, Ni, Mo and Cr contents of the deposited metal significantly improved the strength and toughness. At the lowest strength level (627 MPa), ferrite dominated, mainly acicular ferrite and proeutectoid ferrite. However, at the highest strength level (>800 MPa), bainite dominated, mainly degenerate upper bainite and granular bainite. Good strength toughness match was achieved by a deposited metal having an interlaced multiphase microstructure with degenerate upper bainite and martensite acting as main strengthening phases, and granular bainite and acicular ferrite acting as toughening phases.
YangJ. R., HuangC. Y. and WangS. C.: ‘The development of ultra-low-carbon bainitic steels’, Mater. Des., 1992, 13, 335–338. doi: 10.1016/0261-3069(92)90003-Z
2.
LiJ. W. and LiuQ. S.: ‘The research status on ULCB steel’, J. Tianjin Univ. Technol., 2008, 24, (1), 56–59.
3.
MohrbacherH.: ‘Combined effects of Nb and B micro alloying in molybdenum based ultra low carbon bainitic (ULCB) steels’, J. Iron Steel Res. Int., 2011, 18, 785–791.
4.
BhadeshiaH. K. D. H.: ‘Bainite in steels: transformations, microstructure and properties’, 2nd edn; 2001, London, IOM Communications.
5.
KangJ. S., SeolJ. B. and ParkC. G.: ‘Three-dimensional characterization of bainitic microstructures in low-carbon high-strength low-alloy steel studied by electron backscatter diffraction’, Mater. Charact., 2013, 79, 110–121. doi: 10.1016/j.matchar.2013.02.009
6.
ZhangZ. M., CaiQ. W., YuW., LiX. L. and WangL. D.: ‘Continuous cooling transformation behavior and kinetic models of transformations for an ultra-low carbon bainitic steel’, J. Iron Steel Res. Int., 2012, 19, 73–78.
7.
Lambert-PerladeA., GourguesA. F. and PineauA.: ‘Austenite to bainite phase transformation in the heat-affected zone of a high strength low alloy steel’, Acta Mater., 2004, 52, 2337–2348. doi: 10.1016/j.actamat.2004.01.025
8.
ZhaoW. G., WangW., ChenS. H. and QuJ. B.: ‘Effect of simulated welding thermal cycle on microstructure and mechanical properties of X90 pipeline steel’, Mater. Sci. Eng. A, 2011, A528, 7417–7422. doi: 10.1016/j.msea.2011.06.046
9.
WangH. H., WuK. M., LeiX. W. and QianY.: ‘Effect of fast cooling process on the microstructure and toughness of heat-affected zone in a high strength pipeline steel X120’, Sci. Technol. Weld. Join., 2012, 17, 309–313. doi: 10.1179/1362171812Y.0000000009
10.
LiuH., XueX. H. and LiJ. H.: ‘Research progress on microstructure and properties of ULCB weld metal’, Hot. Work. Technol., 2012, 41, 138–140.
11.
‘Specification for low-alloy steel electrodes and rods for gas shielded arc welding’, A5.28/A5.28M2005, Miami, FL, AWS.
12.
‘Standard methods for mechanical testing of welds’, B4.02007, Miami, FL, AWS.
13.
‘Metal-inspection method of microstructure’, 132981991, Beijing, GB/T.
14.
ItoY. and BessyoK.: ‘Cracking parameter of high strength steels related to HAZ cracking’, J. Jpn Weld. Soc., 1968, 37, 983–991. doi: 10.2207/qjjws1943.37.983
15.
OzakiH., NaimanJ. and MasubuchiK.: ‘A study of hydrogen cracking in underwater steel welds’, Weld. J., 1977, 56, 231s–237s.
16.
RicksR. A., HowellP. R. and BarritteG. S.: ‘The nature of acicular ferrite in HSLA steel weld metals’, J. Mater. Sci., 1982, 17, 732–740. doi: 10.1007/BF00540369
17.
EasterlingK.: ‘Introduction to the physical metallurgy of welding’, 2nd edn; 1992, Oxford, Butterworth-Heinemann.
18.
KouS.: ‘Welding metallurgy’, 2nd edn; 2003, Hoboken, NJ, John Wiley and Sons.
19.
PorterD. A., EasterlingK. E. and SherifM. Y.: ‘Phase transformations in metals and alloys’, 3rd edn; 2009, Boca Raton, FL, Taylor and Francis.
20.
FairchildD., MaciaM., BangaruN., KooJ., OzekcinA. and JinH.: ‘Welding development for the world's strongest pipeline: X120’. Proc. 7th Int. Conf. on ‘Trends in welding research’, Georgia, USA, May 2005, Callaway Gardens Resort, Pine Mountain, 749–754.
21.
ZajacS., SchwinnV. and TackeK. H.: ‘Characterisation and quantification of complex bainitic microstructures in high and ultra-high strength linepipe steels’, Mater. Sci. Forum, 2005, 500-501, 387–394. doi:
10.4028/www.scientific.net/MSF.500-501.387
22.
YamadaT., TerasakiH. and KomizoY.: ‘Microscopic observation of inclusions contributing to formation of acicular ferrite in steel weld metal’, Sci. Technol. Weld. Join., 2008, 13, 118–125. doi: 10.1179/174329308X271797
23.
TakadaA., TerasakiH. and KomizoY.: ‘Effect of aluminium content on acicular ferrite formation in low carbon steel weld metals’, Sci. Technol. Weld. Join., 2013, 18, 91–97. doi: 10.1179/1362171812Y.0000000086
24.
ZhangT. L., LiZ. X., YoungF., KimH. J., LiH., JingH. Y. and TillmannW.: ‘Global progress on welding consumables for HSLA steel’, ISIJ Int., 2014, 54, 1472–1484. doi: 10.2355/isijinternational.54.1472
25.
ZhangT. L., LiZ. X., KouS., JingH. Y., LiG. D., LiH. and KimH. J.: ‘Effect of inclusions on microstructure and toughness of deposited metals of self-shielded flux cored wires’. Mater. Sci. Eng. A, 2015, A628, 332–339.
