Melt flow velocity in high pressure die casting: Its effect on microstructure and mechanical properties in an Al

Abstract

Analysis of as cast tensile specimens of Australian alloy CA313 (an equivalent of A380) made using the high pressure die casting process at three different melt flow velocities has revealed that increasing melt velocity resulted in a finer microstructure and a reduced pore volume fraction and, consequently, better mechanical properties. Mechanical properties are shown to increase more than proportionately with reducing pore volume fraction and the reason for this is demonstrated to be the contribution from the more refined microstructure. The gate used in the investigation was unusual in that its geometry encouraged and prolonged the shearing of the melt. It is proposed that the microstructure was refined by flow shear, the rate of which increased with melt velocity and consequently enhanced the fragmentation of the externally solidified α-Al grains and inclusions such as oxides, cold flakes and gas bubbles.

Keywords

AL-SI ALLOY HIGH PRESSURE DIE CASTING MECHANICAL PROPERTIES MELT FLOW VELOCITY MICROSTRUCTURE POROSITY

Get full access to this article

View all access options for this article.

References

Wang

Q. G.

, Apelian

and Lados

D. A.

: J. Light Met., 2001, 1, 73–84.

Wang

Q. G.

, Crepeau

P. N.

, Griffiths

J. R.

and Davidson

C. J.

: in ‘Shape casting: the John Campbell Symposium’, (ed. Tiryakioglu

and Crepeau

P. N.

), 205-214; 2005, San Francisco, CA, The Minerals, Metals and Materials Society.

Vinarcik

E. J.

: ‘High integrity die casting processes’, 5-11; 2003, Hoboken, NJ, John Wiley and Sons.

Apelian

and Makhlouf

M. M.

: ‘High integrity aluminium die casting: alloys, processes, and melt preparation’, 1-14; 2004, Rosemont, IL, North American Die Casting Association.

, Zhen

and Fan

: Mater. Sci. Technol., 2005, 21, 1019–1024.

Fan

: Proc. 9th Int. Conf. on ‘Aluminium alloys’, Brisbane, Australia, August 2004, Institute of Materials Engineering Australasia Ltd,1092–1097.

Karban

: ‘The effects of intensification pressure, gate velocity, and intermediate shot velocity on the internal quality of aluminum die castings’, PhD thesis, Purdue University, West Lafayette, IN, USA, 2000.

Ghomashchi

M. R.

: J. Mater. Proc. Technol., 1995, 52, 193–206.

Ghomashchi

: in ‘Materials forum’, (ed. Nie

J. F.

.), Vol. 28, 1290-1296; 2004, Melbourne, Institute of Materials Engineering Australasia Ltd.

10.

Niu

X. P.

, Tong

K. K.

, Hu

B. H.

and Pinwill

: Int. J. Cast Met. Res., 1998, 11, 105–112.

11.

Davis

A. J.

and Robinson

P. M.

: Proc. Conf., Detroit, MI, USA, March 1975, Society of Die Casting Engineers, Paper No. G-T75-122.

12.

Herman

E. A.

: ‘Gating die casting dies’, 1-3 and 73-93; 1995, Rosemont, IL, North American Die Casting Association.

13.

Pitsaris

, Savage

and Abbott

: Proc. 22nd NADCA International Die Casting Cong., Indianapolis, IN, USA, September 2003, North American Die Casting Association,195–203.

14.

Kittel-Sherri

: ‘High pressure die cast alloy AZ91D — the effect of casting parameters on quality’, Masters thesis, The University of Queensland, Brisbane, Australia, 2001.

15.

Klein

: Proc. 51st Annual World Magnesium Conf., Berlin, Germany, May 1994, International Magnesium Association (USA),35–43.

16.

Robinson

P. M.

and Murray

M. T.

: Metall Forum, 1978, 1, 26–34.

17.

O'Donnell

: Die Cast. Eng., 2005, 49, 43–47.

18.

Gunasegaram

D. R.

, Givord

, O'Donnell

R. G.

and Polivka

F. B.

: Proc. 13th Conf. on ‘Die casting’, (ed. Gulizia

), Melbourne, Vic., Australia, October 2006, Australian Die Casting Association, Paper No. P09.

19.

Sully

L. J. D.

: in ‘Metals handbook’, (ed.

Davis

J. R.

et al),Vol. 15, 286-295; 1988, Materials Park, OH, American Society for Metals.

20.

Rogers

and Savage

: Proc. 21st NADCA International Die Casting Cong., Indianapolis, IN, USA, October—November 2001, North American Die Casting Association,293–297.

21.

Wang

, Nguyen

, Savage

and Davidson

: Int. J. Cast Met. Res., 2003, 16, 409–417.

22.

Anon.: ‘Aluminium standards and data — ingots and castings’, 35; 1997, Canberra, Australian Die Casting Association.

23.

In ‘Annual Book of ASTM Standards’, Vol. 02.02, ‘Standard methods of tension testing wrought and cast aluminum and magnesium alloy products’, ASTM Standard B 557M-02a, West Conshohocken, PA, USA, (Appendix) 448, 2003.

24.

Caceres

C. H.

and Selling

B. I.

: Mater. Sci. Eng. A, 1996, A220, 109–116.

25.

Kaufman

J. G

and Rooy

E. L.

: ‘Aluminium alloy castings — properties, processes and applications’, 29-31, 35 and 51-52; 2005, Materials Park, OH, ASM International.

26.

Chen

Z. W.

and Jahedi

M. Z.

: Int. J. Cast Met. Res., 1998, 11, 129–138.

Melt flow velocity in high pressure die casting: Its effect on microstructure and mechanical properties in an Al–Si alloy

Abstract

Keywords

Get full access to this article

References