Titanium aluminide alloys offer considerable promise for use in high temperature applications, such as gas turbines. In this study an extruded Ti–46Al–5Nb–1W alloy has been examined, in terms of its tensile and creep behaviour. A reasonably fine and uniform microstructure was found in this bar product. This gave excellent properties, with tensile strengths up to ∼950 MPa at room temperature, along with 1 elongation. These properties were accompanied by a very good creep behaviour, with low primary strains at the lower stresses and very low secondary creep rates. Comparison of the creep properties of this titanium aluminide alloy with other similar compositions and some typical nickel alloys shows that it is significantly superior to first generation titanium aluminides but also nickel alloys, such as IN718 and Udimet 720Li. However, the strain controlled fatigue performance of the titanium aluminide alloy was significantly poorer than these same wrought nickel alloys.
LupincV, MarchionniM, NazmyM, OnofrioG, RemyL, StaubliM, YinWM:‘High temperature mechanical properties evaluation of a γ-TiAl base industrially developed intermetallic alloy’Proc. Conf. on ‘Structural intermetallics’(, NathalM V, et al..), 515–522; 1997, Warrendale, PA, TMS.
5.
LupincV, MarchionniM, NazmyM, OnofrioG, StaubliM, ZhouLZ: ‘Creep, fatigue and crack propagation of a new industrially developed γ-TiAl’, Proc. Conf. Int. Symp. on ‘Structural intermetallics’, 709–716; 2001, Warrendale, PA, TMS.
MartinPL, JainSK, StuckeMA:‘Microstructure and mechanical properties of wrought near-γ-TiAl alloys’Proc. Conf. on ‘Gamma titanium aluminides’(, KimY-W, et al..), 727–736; 1995, Warrendale, PA, TMS.
8.
ThomasM, NakaS, KhanT:‘On the very high room temperature ductility obtained in B2 and/or O-base titanium aluminides’Proc. Conf. Titanium ’95(, BlenkinsopP A, et al..), 388–395; 1996, London, Institute of Material.
9.
FuchsGE: ‘Effect of W additions to Ti–48Al–2Nb–2Cr alloys’,Mater. Sci. Eng. A, 1995, A192/A193, 707–715.
10.
KimY.-W, DimidukDM:‘Designing gamma TiAl alloys: fundamentals, strategy and production’Proc. Conf. Structural Intermetallics 1997(, NathalM V, et al..), 531–543; 1997, Warrendale, PA, TMS.
11.
ColvinJJ, HardyMC, KerryS, PartridgeA: ‘Microstructure and mechanical properties of T–48Al–2Mn–2Nb and Ti–47Al–2Mn–2Nb–XD alloys’, DRA Report DRA/SMC/WP972035, 1997.
12.
ZhangWJ, DeeviSC: ‘Analysis of the minimum creep rate of TiAl alloy’,Mater. Sci. Eng. A, 2003, A362, 280–291.
13.
‘High temperature, high strength nickel base alloys’; 1997, London, The Nickel Development Institute.
14.
WilcockIM, ColeDG, BrooksJW, HardyMC: ‘Creep/fatigue behaviour of P/M nickel disc alloy’, Proc. Conf. 6th Int. Charles Parsons Turbine Conf. 2003, 749–764; 2003, London, The Institute of Materials, Minerals and Mining.
15.
ZhangWJ, DeeviSC: ‘The controlling factors in primary creep of TiAl-base alloys’,Intermetallics, 2003, 11, 177–185.
16.
Es-SainiM, BartlesA, WagnerR: Acta Metall. Mater., 1995, 43, 153.
17.
DraperSL, DasG, LocciI, WhittenbergerJD, LerchBA, KestlerH:‘Microstructure and mechanical properties of extruded Gamma Met PX’Proc. Conf. on ‘Gamma titanium aluminides’(, KimY-W, et al..), San Diego, CA, 207–212; 2003, Warrendale, PA,TMS.
18.
EvansRW, WilshireB: ‘Creep of metals’, 121; 1985, London, Institute of Metals.
MonkmanFC, GrantNJ: ‘An empirical relationship between rupture life and minimum creep rate in creep rupture tests’, Proc. 59th Annual Meeting of ASTM, Philadelphia, PA, USA, 1956, ASTM, 593–605.
21.
PatherR, MittenWA, HoldwayP, UbhiHS, WisbeyA, BrooksJW: ‘The effect of high temperature exposure on the tensile properties of γ-TiAl alloys’,Intermetallics, 2003, 11, 1015–1027.
22.
ReedPAS, EverittS, WisbeyA, Di MartinoI, BrooksJW: ‘High temperature fatigue and creep performance of N18 alloy’, Proc. Conf. Parsons 2007, Glasgow, UK, September 2007, Strathclyde University, 309–319.
23.
GloanecAL, JouiadM, BertheauD, GrangeM, HenaffG: ‘Low-cycle fatigue and deformation substructures in an engineering TiAl alloy’,Intermetallics, 2007, 15, 520–531.
24.
RecinaV: ‘High temperature low cycle fatigue properties of two cast gamma titanium aluminide alloys with refined microstructure’,Mater. Sci. Technol., 2000, 16, 333–340.
