Development of recycled polymer composites for structural applications

Abstract

This paper is concerned with the formulation of composite materials for structural or semistructural applications using thermoplastic polymer waste. The mechanical and thermal properties of a proprietary blend of recycled polymers with a range of different fillers were investigated. The effect varied with the aspect ratio of the filler and the mode of loading. Spherical calcium carbonate gave a marginal improvement in modulus. Plate-like mica produced a significant increase in modulus without reduction in strength. Glass fibres caused a significant increase in modulus and strength while decreasing the linear coefficient of thermal expansion. Hybrid systems containing glass fibre and a lower aspect ratio filler were also investigated to obtain a material system which combines high properties and reasonably low cost. It was found that addition of small quantities of mica to glass fibre reinforced blends exhibited a significant synergy in tensile strength and modulus.

Keywords

Recycled Thermoplastic Mica Glass fibre Polymer blend Composites

Get full access to this article

View all access options for this article.

References

Goodship

: ‘Introduction to plastic recycling’, 2nd edn; 2007, Shrewsbury, SmithersRapra Technology Limited.

‘Domestic mixed plastics packaging. Waste management options’, Technical report, WRAP, Banbury, UK, 2008.

Brandrup

, ed (ed.): ‘Recycling and recovery of plastics’; 1996, Munich, HanserVerlag.

Morrow

, Nosker

, VanNess

, Renfree

: ‘Method of deriving polystyrene and polyolefin plastics composite from recycled plastics’, US patent 5,298,214, 1994.

Tolinski

: ‘Additives for polyolefins: getting the most out of polypropylene, polyethylene and TPO’; 2009, Oxford, Elsevier Science Ltd.

Technology Plastics Omya AG : ‘Review technical information plastics R4-04 omyalene 102 M in PO pipes’, 2003, http://www.omya.com

Pritchard

: ‘Plastics additives’, Rapra market report, Rapra Technology Ltd, Shrewsbury, UK, 2005.

Pritchard

: ‘Plastics additives: an A–Z reference’; 1998, London, Chapman & Hall.

Hartikainen

, Hine

, Szabo

, Lindner

, Harmia

, Duckett

, Friedrich

: Compos. Sci. Technol ., 2005, 65, 257–267.

10.

Zhao

, Huang

, Sun

, Dai

: J. Appl. Polym. Sci ., 2001, 82, 2719–2728.

11.

Scelsi

, Hodzic

, Soutis

, Hayes

, Rajendran

, AlMa'adeed

, Kahraman

: Plast. Rubber Compos ., 2011, 40, (1), 1–10.

12.

Nurdina

, Mariatti

, Samayamutthirian

: J. Vinyl Add. Technol ., 2009, 15, (1), 20–28.

13.

Wypych

: ‘Handbook of fillers’; 1999, Toronto, ChemTec Publishing.

14.

‘Tests for flammability of plastic materials for parts in devices and appliances’, UL 94, Underwriters Laboratories Inc., Northbrook, IL, USA, 1996.

15.

Z.-L

, Gao

J.-G

, Bai

L.-G

: J. Appl. Polym. Sci ., 2004, 92, 1388–1391

16.

Z.-L

, Gao

J.-G

, Niu

H.-J

, Ding

H.-T

, Zhang

: J. Appl. Polym. Sci ., 2002, 85, 257–262.

17.

Jackson

, Nosker

: Proc. DoD Corrosion Conf., Washington, DC, USA, August 2009, Department of Defense (DoD), Paper 15259.

18.

Nairn

, Zoller

: J. Mater. Sci ., 1985, 20, (1), 355–367.

19.

Robert

: ‘Structural adhesive joints in engineering’; 1997, London, Chapman & Hall.

20.

Hayward

: ‘Steel detailers’ manual’; 2002, Oxford, Wiley-Blackwell.

21.

‘Guidelines for early-opening-to-traffic Portland cement concrete for pavement rehabilitation’, NCHRP report no. 540, Transportation Research Board of the National Academies, Washington, DC, USA, 2005.