A thin monolayer and multilayer physical vapour deposition film was prepared on tool steel substrates using an unbalanced magnetron sputtering technique. Characteristics of multilayer (Mo/MoN, Ti/TiN, Cr/CrN, W/W2N; A/B = 0·6∶0·3 μm) and monolayer (MoN, TiN, CrN, W2N; 0·6 μm) coatings were investigated concerning the phase composition and coating adhesion. The multilayer film sliding against alumina (Al2O3) and steel balls (100Cr6) had good wear resistance and very long service life at room temperature compared to monolayer analogues. In order to evaluate the drilling performance in wet condition four surfactants, i.e. zinc dithiodiphosphate, sodium dodecyl sulphate, sodium hexametaphosphate and cetyl trimethylammonium bromide as 1 wt-% were used with polyalphaolefin base oil. A significant reduction in flank wear rate was measured under wet condition.
KathreinM, MichotteC, PenoyMPolcikP and MittererC: ‘Multifunctional multi-component PVD coatings for cutting tools’, Surf. Coat. Technol., 2005, 200, 1867–1871.
2.
DeySP and DeeviSC: ‘Single layer and multilayer wear resistant coatings of (Ti,Al)N: a review’, Mater. Sci. Eng. A, 2003, A342, 58–79.
3.
KothariDC and KaleAN: ‘Recent trends in surface engineering using cathodic arc technique’, Surf. Coat. Technol., 2002, 158–159, 174–179.
4.
KulkarniAP, JoshiGG and SargadeVG: ‘Performance of PVD AlTiCrN coating during machining of austenitic stainless steel’, Surf. Eng., 2013, 29, (5), 402–407.
5.
McIntyreD, GreeneJE, HåkanssonG, SundgrenJE and MünzWD: ‘Oxidation of metastable single-phase polycrystalline Ti0·5Al0·5N films: kinetics and mechanisms’, J. Appl. Phys., 1990, 67, 1542–1543.
6.
SmithIJ, MünzWD, DonohueLA, PetrovI and GreeneJE: ‘Improved Ti1–xAlxN PVD coatings for dry high speed cutting operations’, Surf. Eng., 1998, 14, (1), 37–42.
7.
HarrisSG, DoyleED, VlasveldAC and J DolderP: ‘Dry cutting performance of partially filtered arc deposited titanium aluminium nitride coatings with various metal nitride base coatings’, Surf. Coat. Technol., 2001, 146–147, 305–311.
8.
HelmerssonU, TodorovaS, BarnettSA, SundgrenJE, MarkertLC and GreeneJE: ‘Growth of single-crystal TiN/VN strained-layer superlattices with extremely high mechanical hardness’, J. Appl. Phys., 1987, 62, 481–484.
9.
YasharPC and SproulWD: ‘Nanometer scale multilayered hard coatings’, Vacuum, 1999, 55, 179–190.
10.
BasuA, MajumdarJD and MannaI: ‘Structure and properties of CrxN coating’, Surf. Eng., 2012, 28, (3), 199–204.
11.
KhlifiK, BenC and LarbiA: ‘Investigation of adhesion of PVD coatings using various approaches’, Surf. Eng., 2013, 29, (7), 555–560.
12.
JiJ, NiuY, WuJ and YuZ: ‘Improvement of properties of TiN coating by optimising microstructural design’, Surf. Eng., 2014, 30, (1), 36–40.
13.
DesmaisonJ, LefortP and BillyM: ‘Oxidation of titanium nitride in oxygen: Behavior of TiN0·83 and TiN0·79 plates’, Oxid. Met., 1979, 13, (3), 203–222.
14.
WahlströmU, HultmanL, SundgrenJE, AdibiF, PetrovI and GreeneJE: ‘Crystal growth and microstructure of polycrystalline Ti1−x
Al
x
N alloy films deposited by ultra-high-vacuum dual-target magnetron sputtering’, Thin Solid Films, 1993, 235, 62–70.
15.
UpadhyayRK and KumaraswamidhasLA: ‘Surface modification by multilayered W/W2N coating’, Surf. Eng., 2014, 30, (7), 475–482.
16.
KıvakT, SamtaşG and ÇiçekA: ‘Taguchi method based optimisation of drilling parameters in drilling of AISI 316 steel with PVD monolayer and multilayer coated HSS drills’, Measurement, 2012, 45, 1547–1557.
17.
BraicV, ZoitCN, BalaceanuMKissA, VladescuA, PopescuA and BraicM: ‘TiAlN/TiAlZrN multilayered hard coatings for enhanced performance of HSS drilling tools’, Surf. Coat. Technol., 2010, 204, 1925–1928.
18.
AubertA. DanrocJ, GauchcrA and TerratJP: ‘Hard chrome and molybdenum coatings produced by physical vapour deposition’, Thin Solid Films, 1985, 126, 61–67.
19.
RudnikPJ, GrahamME and SproulWD: ‘High rate reactive sputtering of MoNx coatings’, Surf. Coat. Technol., 1991, 49, 293–297.
20.
BabaK and HatadaR: ‘Corrosion-resistant titanium nitride coatings formed on stainless steel by ion-beam-assisted deposition’, Surf. Coat. Technol., 1994, 66, 368–372.
21.
AnithaVP, BhattacharyaA, PatilNitinG and MajorS: ‘Study of sputtered molybdenum nitride as a diffusion barrier’, Thin Solid Films, 1993, 236, 306–310.
22.
KacsichT and LiebKP: ‘Oxidation of thin CrN and Cr2N films analyzed via nuclear reaction analysis and Rutherford backscattering spectrometry’, Thin Solid Films, 1994, 245, 4–6.
23.
WilsonA, MatthewsA, HousdenJ, TurnerR and GarsideB: ‘A comparison of the wear and fatigue properties of plasma-assisted physical vapour deposition TiN, CrN and duplex coatings on Ti–6Al–4V’, Surf. Coat. Technol., 1993, 62, 600–607.
24.
HollekH: ‘Material selection for hard coatings’, J. Vac. Sci. Technol. A, 1986, 4A, (6), 2661–2669.
25.
AubertA, GilletR, GaucherA and TerratJP: ‘Hard chrome coatings deposited by physical vapour deposition’, Thin Solid Films, 1983, 108, 165–172.
26.
GuruvenketS and RaoGM: ‘Bias induced structural changes in tungsten nitride films deposited by unbalanced magnetron sputtering’, Mater. Sci. Eng. B, 2004, B106, 172–176.
27.
TliliB, NouveauC, WalockMJ, NasriM and GhribT: ‘Effect of layer thickness on thermal properties of multilayer thin films produced by PVD’, Vacuum, 2012, 86, 1048–1056.
28.
BouzakisKD, MakrimallakisS, KatirtzoglouG, SkordarisG, GerardisS, BouzakisE, LeyendeckerT, BolzS and KoelkerW: ‘Adaption of graded Cr/CrN-interlayer thickness to cemented carbide substrates’ roughness for improving the adhesion of HPPMS PVD films and the cutting performance’, Surf. Coat. Technol., 2010, 205, 1564–1570.
29.
JosephMC, TsotsosC, BakerMA, KenchPJ, RebholzC, MatthewsA and LeylandA: ‘Characterisation and tribological evaluation of nitrogen-containing molybdenum–copper PVD metallic nanocomposite films’, Surf. Coat. Technol., 2005, 190, 345–356.
30.
ZhaoF, SongZX, ZhangGF, HouXD and DengDW: ‘Effects of substrate bias on structure and mechanical properties of AlCrTiWNbTa coatings’, Surf. Eng., 2013, 29, (10), 778–782.
31.
PangJ, BaiY, QinF, PanL, ZhaoY and KangR: ‘Deposition of Ti–Si–N films on Al substrates by magnetron sputtering’, Surf. Eng., 2013, 29, (10), 749–754.
32.
PriyadarshiniBG, GuptaMK, GhoshS, ChakrabortyM and AichS: ‘Role of substrate bias during deposition of magnetron sputtered Ni, Ti and Ni–Ti thin films’, Surf. Eng., 2013, 29, (9), 689–694.
33.
KottferD, FerdinandyM, KaczmarekL, MaňkováI and BeňoJ: ‘Investigation of Ti and Cr based PVD coatings deposited onto HSS Co 5 twist drills’, Appl. Surf. Sci., 2013, 282, 770–776.
34.
ThaiwatthanaS, JantapingN and LimthongkulP: ‘Residual stress measurement of low temperature plasma surface alloyed layer using X-ray diffraction techniques’, Surf. Eng., 2012, 28, (4), 273–276.
35.
GhribT, TliliB, NouveauC, BenlatrecheY, LambertinM, YacoubiN and EnnasriM: ‘Experimental investigation of the mechanical micro structural and thermal properties of thin CrAIN layers deposited by PVD technique for various aluminum percentages’, Phys. Proc., 2009, 2, 1327–1336.
36.
ShenYG, MaiYW, McKenzieDR, ZhangQC, McFallWD and McBrideWE: ‘Composition, residual stress, and structural properties of thin tungsten nitride films deposited by reactive magnetron sputtering’, J. Appl. Phys., 2000, 88, 1380–1388.
37.
GassnerG, MayrhoferPH, KutschejK, MittererC and KathreinM: ‘Magnéli phase formation of PVD Mo–N and W–N coatings’, Surf. Coat. Technol., 2006, 201, 3335–3341.
38.
RybiakR, FouvryS, LiskiewiczT and WendlerB: ‘Fretting wear of a TiN PVD coating under variable relative humidity conditions – development of a ‘composite’ wear law’, Surf. Coat. Technol., 2008, 202, 1753–1763.
39.
HsuCH, LinCK, HuangKH and OuKL: ‘Improvement on hardness and corrosion resistance of ferritic stainless steel via PVD-(Ti,Cr)N coatings’, Surf. Coat. Technol., 2013, 231, 380–384.
40.
HolmbergK and Matthews (eds.)A: ‘Coating tribology: properties, techniques and applications in surface engineering’; 1994, Amsterdam, Elsevier.
41.
UpadhyayRK and KumaraswamidhasLA: ‘Tungsten/tungsten nitride performance at elevated temperature’, Mater. High Temp., 2014, 31, (2), 102–108.
42.
LarssonM, BromarkM, HedenqvistP and HogmarkS: ‘Deposition and mechanical properties of multilayered PVD Ti–TiN coatings’, Surf. Coat. Technol., 1995, 76–77, 202–205.
43.
ShenYG, MaiYW, ZhangQC, McKenzieDR, McFallWD and McBrideWE: ‘Residual stress, microstructure, and structure of tungsten thin films deposited by magnetron sputtering’, J. Appl. Phys., 2000, 87, 177–187.
44.
LiuC, BiQ and MatthewsA: ‘EIS comparison on corrosion performance of PVD TiN and CrN coated mild steel in 0·5 N NaCl aqueous solution’, Corros. Sci., 2001, 43, 1953–1961.
45.
ÜrgenM, EryilmazOL, ÇakirAF, KayaliES, NilüferB and IşikY: ‘Characterization of molybdenum nitride coatings produced by arc-PVD technique’, Surf. Coat. Technol., 1997, 95, 501–506.
46.
PerryAJ, BaouchiAW, PetersenJH and PozderSD: ‘Crystal structure of molybdenum nitride films made by reactive cathodic arc evaporation’, Surf. Coat. Technol., 1992, 54–55, 261–265.
47.
TianB, YueW, FuZ, GuY, WangC and LiuJ: ‘Microstructure and tribological properties of W-implanted PVD TiN coatings on 316L stainless steel’, Vacuum, 2014, 99, 68–75.
48.
PolcarT, ParreiraNMG and CavaleiroA: ‘Structural and tribological characterization of tungsten nitride coatings at elevated temperature’, Wear, 2008, 265, 319–326.
49.
PolcarT, ParreiraNMG and CavaleiroA: ‘Tribological characterization of tungsten nitride coatings deposited by reactive magnetron sputtering’, Wear, 2007, 262, 655–665.
50.
AouadiSM, LusterB, KohliP, MuratoreC and VoevodinAA: ‘Progress in the development of adaptive nitride-based coatings for high temperature tribological applications’, Surf. Coat. Technol., 2009, 204, 962–968.
51.
DengJX and LiuA: ‘Dry sliding wear behavior of PVD TiN, Ti55Al45N, and Ti35Al65N coatings at temperatures up to 600°C’, Int. J. Refract. Met. Hard Mater., 2013, 41, 241–249.
52.
BarnesAM, BartleKD and ThibonVRA: ‘A review of zinc dialkyldithiophosphates (ZDDPS): characterisation and role in the lubricating oil’, Tribol. Int., 2001, 34, 389–395.
53.
BlancoD, GonzálezR, BattezAH, ViescaJL and GonzálezAF: ‘Use of ethyl-dimethyl-2-methoxyethylammonium tris(pentafluoroethyl)trifluorophosphate as base oil additive in the lubrication of TiN PVD coating’, Tribol. Int., 2011, 44, 645–650.
54.
BattezAH, GonzálezR, ViescaJL, GonzálezAF and HadfieldM: ‘Lubrication of PVD coatings with ethyl-dimethyl-2-methoxyethylammonium tris(pentafluoroethyl)trifluorophosphate’, Tribol Int., 2013, 58, 71–78.
55.
GuJ, TungS and BarberG: ‘Wear process in manufacturing’, ASTM STP 1362, ASTM, West Conshohocken, PA, USA, 31–47, 1999.
56.
UpadhyayRK, KumaraswamidhasLA: ‘On the influence of surfactant over friction properties of steel’, Chem. Phys. Lett., 2014, 608, 167–172.
57.
BielemanJ (Ed.): ‘Additives for coatings’; 200, Weinheim, Wiley-VCH.
58.
MillerCA and NeogiP: ‘Interfacial phenomena equilibrium and dynamic effects’; 2008, Boca Raton, FL, CRC Press.
